EZTRUNK 1900 0057 User manual

Page 1 1900 0057-M400-Ver. A
08/09/21
CUSTOMER SERVICE: [email protected]
Text & Call : 203-901-0055 / Call 203-591-9060
PO#
:
Print the latest manual &
Watch the EZTRUNK Video
Part # 1900 0057
Scan QR CODE for Video &
PDF MANUALS
MAKE IT
#1900 0057
M400
EZTRUNK GUN HOLDER
MANUAL
ASSEMBLY
WE ARE HERE TO HELP YOU!
Customer Service
Any question call
EMAIL US: [email protected]
Call 203-901-0055 / 203-591-9060
7 day a week 8:30 am EST

Please read instructions fully before beginning assembly
Page 2
#2 Phillips Screw Driver
NO Illustration Description Part # QTY.
Driver Side Gun Holder
Passenger Side Gun Holder
195706 1
195707 1
1
2
83
RECOMMENDED TOOLS
DO NOT USE ELECTRIC TOOLS! THIS WILL CAUSE SCREWS TO STRIP!
USE SCREW DRIVER, DO NOT OVER TIGHTEN.
1900 0057-M400-Ver. A
08/09/21
CUSTOMER SERVICE: [email protected]
Text & Call : 203-901-0055 / Call 203-591-9060
BEFORE BEGINNING,SEE THE ASSEMBLY INSTRUCTION VIDEO ON EZTRUNK.NETBEFORE BEGINNING,SEE THE ASSEMBLY INSTRUCTION VIDEO ON EZTRUNK.NET
M400
Bolt M6x8mm 66081
Metal Washer - Black 1806012 8
Bolt With Plastic Final 06081 4
Allen Wrench For Wing Clamp 60472 1
Alcohol Pad For Plastic Block 10075 1
Alcohol
Velcro With Loop #251 2
Wrench 1
#10
Drill Bit 1
#7
Rubber Pad insulator
This is for Noise Suppression
where needed
11203 6
4
5
6
7
8
9
10
11

Lay down your EZTRUNK
Page 3
BEFORE BEGINNING,SEE THE ASSEMBLY INSTRUCTION VIDEO ON EZTRUNK.NET
1900 0057-M400-Ver. A
08/09/21
CUSTOMER SERVICE: [email protected]
Text & Call : 203-901-0055 / Call 203-591-9060
BEFORE BEGINNING,SEE THE ASSEMBLY INSTRUCTION VIDEO ON EZTRUNK.NET
Make sure the gun holder location is enable to fold the
top panel of EZTRUNK when doesn’t use it.
Make sure enough space from top panel to reach your
gun.
Do not install gun holder on inside door of EZTRUNK if
you have JLU and JKU EZTRUNK
1. Loose 4 screws and slid the L shape bracket adjust slot
to make enough space to store the gun.
2. Tighten screws after adjusted slot
Slot L shape
bracket
JLU 2018 & UP 4 DOOR EZTRUNK
or JKU 2011 - 2018 4 DOOR EZTRUNK
Adjust Slot On Gun Holder
195706
Drive side
195707
Passenger side
1. Put the gun and gun holder on back panel of EZTRUNK to check your
prefer location
2. Use a pen to make a mark on back panel of EZTRUNK, Use 2 screws
for 1 gun holder
2
3
2A 2B
2C
1

Page 4 1900 0057-M400-Ver. A
08/09/21
CUSTOMER SERVICE: [email protected]
Text & Call : 203-901-0055 / Call 203-591-9060
BEFORE BEGINNING,SEE THE ASSEMBLY INSTRUCTION VIDEO ON EZTRUNK.NET
Customer Service
Any question call
EMAIL US: [email protected]
Call 203-901-0055 / 203-591-9060
7 Day a week 8:30 am EST
66081
1806012
06081
Adjust Bungee Tension
HOW TO USE GUN HOLDER
GUN HOLDER FOLDED
Locked nut
Bottom screw
Velcro Loop
Top screw
Loosen locked nut a little, Pull the bungee to hook the ring
to the screw with right tension to hold the gun. You can
hook Bottom screw or Top screw.
1. Use Drill bit to make the hole on back panel
2. Use 2 blots and 2 washers assemble gun holder to the
EZTRUNK
1. Use the alcohol wipe to clean the Velcro go area on
back panel. Make sure it is dry after applying the Velcro
Loop side on the panel.
2. Make sure it is right location for Velcro Loop side when
gun holder folded.
1. Fold the gun holder up, use Bolt #06081 to fix in place
2. Unclip the bungee
1. Hook the gun on both side holder
2. Clip the ring to the screw
1. Take out the gun
2. Unfold the gun holders
and screw back Bolt
#06081 to same hole.
66081
1806012
Back Panel of EZTRUNK
4 5
6 7
89