Ezviz Rc3 User manual

Robot Vacuum Cleaner

1

PRODUCT SAFETY PRECAUTIONS

Before using this product, please read all the contents of this user

manual carefully, install the device accordingly and save this manual for

future reference properly. To lower the risk of fire, electric shock or other

injuries, please observe the following operation requirements:

• This appliance is not intended for use by people (including children) with

reduced physical, sensory or mental capabilities, or lack of experience

and knowledge, unless they have been given supervision or instruction

concerning use of the appliance by a person responsible for their safety.

Children should be supervised to ensure that they do not play with the

appliance.

• ForEuropean,thisappliancecanbeusedbychildrenagedfrom8years

and above and people with reduced physical, sensory or mental

capabilities or lack of experience and knowledge if they have been given

supervision or instruction concerning use of the appliance in a safe way

and understand the hazards involved. Cleaning and user maintenance

shall not be made by children without supervision. Children should not

play with the appliance.

• Please don’t suction high-temperature substances (unextinguished

cigarettebutts,matches,hotashesandetc.),supernesubstances(like

lime, cement, sawdust, gesso, ashes and toner), large sharp fragments

(notphysicallydenitematterslikeglass).

• No action needed to shift the product between 50 and 60Hz, product can

adapt itself for both 50 and 60Hz.

• If the supply cord is damaged, it must be replaced by the manufacturer,

itsserviceagentorsimilarlyqualiedpersonsinordertoavoidahazard.

• When charging, please use the Charging Base CS-RE5-CB offered by

EZVIZ.

• WARNING: To Reduce The Risk Of Electric Shock - Do not use outdoors

or on wet surfaces, commercial or industrial environments.

• WARNING: To Reduce The Risk Of Electric Shock - Use indoors only.

SAFETY WARNING

2

• WARNING: To Reduce The Risk Of Electric Shock – Unplug Before

Servicing.

• The charging base can only charge lithium-ion batteries containing no

more than 8 cells with a rated capacity of no more than 2600mAh.

• The charging base can not be charged to non-rechargeable batteries.

PROPER USE OF THE DEVICE

• Thedeviceisonlyusedforcleaningtheoorofthehomeenvironment,

and should not be used in outdoor environment (such as open balconies),

non-ground environment (such as stairs), and industrial environment.

• Don’t use the device in suspended environment (such as duplexes, open

balconies and the top of furniture) without protective facilities.

• Children are not allowed to use the device as a toy. Please keep children

and pets away from the device when using it. Don’t put accessories

such as side brush in the place where children can reach, so as to

prevent children from eating by mistake. Don’t place children and pets

on the device body.

• Don’tusethedeviceinanenvironmentwithopenreorfragileobjects.

• Don’tusethedeviceonwaterloggedoorsorwetground.

• Don’t use the device in an environment higher than 40°C or lower than

0°C.

• Don’tusethedevicetocleananyammablematerials(suchasgasoline,

toner).Don’tusethedeviceintheareawithammablematerials.

• Don’t use the device to clean burning items, such as matches, cigarettes

andotheritemsthatmaycausere.

• Don’t use the product to absorb large stones, waste paper and other

items that may block the product. When the suction port is blocked,

please clean the product in time and remove the dust, cotton, hair, etc.

at the suction port.

• Use only the accessories recommended or sold by the manufacturer.

Don’t use the batteries or docking station of any third party, and don’t

use damaged batteries or docking station.

• Dispose of used batteries in accordance with local laws and regulations.

3

• Don’t burn the device under any circumstances, as the battery may

cause explosion.

• After the RGB camera is contaminated with dust during use, it is

recommended to use the air blower to clean the camera, or use a paper

towel and soft dry cloth to wipe and clean, don’t use rough or hard

materials, so as to avoid scratches on the glass surface of the vision

module.

• If the rear surface of the robot is too dusty, it will affect the recharging of

the robot. It is recommended to clean it regularly or as needed. It is also

recommended to use a paper towel or soft dry cloth to clean it.

• If the surface of the edge sensor on the side of the robot is contaminated

with lots of dust, it will affect the posture and mapping positioning effect

of the robot when walking along the wall. It is recommended to clean it

regularly or as needed. Since the sensor is located inside the body, it is

recommended to use the air blowing tool/paper towel/soft dry cloth for

cleaningthecameratowipethesensor.Don’tputyourngersintoitfor

cleaning.

• The bottom of the robot is easy to be contaminated with lots of dust, so

it is recommended to clean it regularly or as needed.

• Please use the device according to the instructions in the manual. Any

loss and injury caused by improper use shall be borne by the user.

• Please don’t touch the plug or any electrified part of the product with

your wet hands in case of electric shock hazard.

• If you will not use the product for a long time, please turn off the power

and unplug the charging plug.

4

Regulatory Information

This product and - if applicable - the supplied accessories too are marked with “CE” and comply therefore with

the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the RoHS Directive

2011/65/EU, the ErP Directive 2009/125/EC.

2012/19/EU (WEEE directive): Products marked with this symbol cannot be disposed of as unsorted municipal

waste in the European Union. For proper recycling, return this product to your local supplier upon the purchase

of equivalent new equipment, or dispose of it at designated collection points. For more information see: www.

recyclethis.info

2006/66/EC and its amendment 2013/56/EU (battery directive): This product contains a battery that cannot be

disposed of as unsorted municipal waste in the European Union. See the product documentation for specific

battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd),

lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection

point. For more information see:

www.recyclethis.info

Technical Parameters

Direct current

Alternating current

For indoor use.

Before charging, read the instructions.

Robot

Model CS-RC3-TWT2, CS-RC3-TWT5

Overall Dimension 345×345×78.5 mm

Weight Approx. 2.83kg

Battery Capacity 2,600 mAh

Battery Rated Voltage 14.4 V

Rated Input 24V 1A

Rated Power 30W

Charging Base

Model CS-RE5-CB

Rated Input Voltage (Power Adapter) 220-240V~, 50/60Hz

Rated Output 24V 1A

5

Any and all information, including, among others, wordings, pictures, graphs are the properties of

Hangzhou EZVIZ Software Co., Ltd. (hereinafter referred to as “EZVIZ”). This user manual (hereinafter

referred to as “the Manual”) cannot be reproduced, changed, translated, or distributed, partially or

wholly, by any means, without the prior written permission of EZVIZ. Unless otherwise stipulated,

EZVIZ does not make any warranties, guarantees or representations, express or implied, regarding

to the Manual.

About this Manual

The Manual includes instructions for using and managing the product. Pictures, charts, images and

all other information hereinafter are for description and explanation only. The information contained

intheManualissubjecttochange,withoutnotice,duetormwareupdatesorotherreasons.Please

ndthelatestversioninthe ™ website (http://www.ezviz.com).

Revision Record

New release – January 2023

Trademarks Acknowledgement

™, ™, and other EZVIZ’s trademarks and logos are the properties of EZVIZ in various

jurisdictions. Other trademarks and logos mentioned below are the properties of their respective

owners.

Legal Disclaimer

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THE PRODUCT DESCRIBED, WITH

ITS HARDWARE, SOFTWARE AND FIRMWARE, IS PROVIDED “AS IS”, WITH ALL FAULTS AND ERRORS,

AND EZVIZ MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,

MERCHANTABILITY, SATISFACTORY QUALITY, FITNESS FOR A PARTICULAR PURPOSE, AND

NON-INFRINGEMENT OF THIRD PARTY. IN NO EVENT WILL EZVIZ, ITS DIRECTORS, OFFICERS,

EMPLOYEES, OR AGENTS BE LIABLE TO YOU FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR

INDIRECT DAMAGES, INCLUDING, AMONG OTHERS, DAMAGES FOR LOSS OF BUSINESS PROFITS,

BUSINESS INTERRUPTION, OR LOSS OF DATA OR DOCUMENTATION, IN CONNECTION WITH

THE USE OF THIS PRODUCT, EVEN IF EZVIZ HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH

DAMAGES.

TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, IN NO EVENT SHALL EZVIZ’S TOTAL

LIABILITY FOR ALL DAMAGES EXCEED THE ORIGINAL PURCHASE PRICE OF THE PRODUCT.

EZVIZ DOES NOT UNDERTAKE ANY LIABILITY FOR PERSONAL INJURY OR PROPERTY DAMAGE AS

THE RESULT OF PRODUCT INTERRUPTION OR SERVICE TERMINATION CAUSED BY: A) IMPROPER

INSTALLATION OR USAGE OTHER THAN AS REQUESTED; B) THE PROTECTION OF NATIONAL

OR PUBLIC INTERESTS; C) FORCE MAJEURE; D) YOURSELF OR THE THIRD PARTY, INCLUDING

WITHOUT LIMITATION, USING ANY THIRD PARTY’S PRODUCTS, SOFTWARE, APPLICATIONS, AND

AMONG OTHERS.

REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE

WHOLLY AT YOUR OWN RISKS. EZVIZ SHALL NOT TAKE ANY RESPONSIBILITES FOR ABNORMAL

OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK,

HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, EZVIZ

WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS AND DATA

PROTECTION LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR

JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS

TO THE APPLICABLE LAW. EZVIZ SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS

USED WITH ILLEGITIMATE PURPOSES.

IN THE EVENT OF ANY CONFLICTS BETWEEN THE ABOVE AND THE APPLICABLE LAW, THE LATTER

PREVAILS.

6

Table of Contents

Overview ��7

Package Contents�� 7

Basis �� 8

Quick Start Guide ��12

Preparation�� 12

Install the Charging Base�� 12

Connect the Power Supply to the Charging Base �� 13

Place the Robot �� 14

Charging�� 14

Power On/off �� 15

Start Cleaning�� 15

Pause Cleaning�� 16

Sleep�� 16

System Resetting �� 16

Routine Maintenance��16

Dump the Dust Box�� 17

Clean the Main Brush�� 18

Clean/Replace the Side Brush�� 19

Clean Universal Wheel �� 20

Clean Sensors �� 20

Clean the Charging Electrode �� 21

Environmental Precautions��22

FAQ ��23

List of Faults ��25

Appendix ��26

Rechargeable Lithium ion Battery �� 26

INFORMATION FOR PRIVATE HOUSEHOLDS �� 26

7

Overview

Package Contents

Robot Vacuum Cleaner *1

(hereinafter referred as to “Robot”)

Charging Base*1

Side Brush *2

(One has pre-installed in the Robot)

High-performance Filter *2

(One has pre-installed in the Robot)

Power Adapter *1 Cleaning Tool *1

Remote Control *1

(AAA battery *2 included)

Quick Start Guide *2 Regulatory Information *1

• Ahigh-performancelterhavebeeninstalledintheRobot.

• The device’s appearance is subject to the actual one you have bought.

8

Basis

Robot

Microphone

Recharge Sensor

Front Bumper

* Cleaning/On-off Button

Side Brush

* Recharge Button

*Recharge Button

Front Bumper

Side Brush

Microphone

Recharge Sensor

*Cleaning/On-off Button

Button

Recharge Button Press once: Back to charge

Cleaning/On-off Button

• Press once: Start cleaning

• Presstwice:Startxed-pointcleaning

• Press and hold for 4s:Turn on/off the Robot

+ Cleaning/On-off Button +

Recharge Button Press and hold for 15s: Restore to factory settings

Power Indicator

+

Power Indicator

(on Cleaning/On-off Button &

Recharge Button)

• White:batterylevel≥20%

• Pink:batterylevel<20%

• Red: fault or exceptions

• Slow-asheswhite:Incharging

9

Edge Sensor *3

Main Brush

Main Brush Cover

Charging Electrode *2

Universal Wheel

Side Brush

Drive Wheel *2

Side Brush

Universal Wheel

Charging Electrode*2

Edge Sensor*3

Main Brush

Main Brush Cover

Drive Wheel *2

Dust Box

Taking-out Button

Cleaning Tool

Filter Box

Infrared Receiving Terminal

Filter Box

Infrared Receiving Terminal

Cleaning Tool

Dust Box Taking-out Button

Suction Inlet

High-performance Filter

Filter Cover

High-performance Filter

Suction Inlet

10

Charging Base

Charging Base Indicator

Name Description

Charging Base

Indicator

On: Connected to a power supply

Off: Powered off/correctly connected with the Charging Base

Remote Control

Power

Recharge

Time Settings

Appointment Settings

Fixed-point Vacuum

Start/pause

Suction Regulation

Sweep Along the Wall

Power

Recharge

Time Settings

Fixed-point Vacuum

Start/pause

Suction Regulation

Sweep Along the Wall Appointment Settings

11

Please ensure that the Robot will response with a beep after you operate the remote control.

Name Description

Power

Press once when the Robot is standby, it will sleep.

* Under the Sleep Mode, the Robot will enter a low energy-comsumption state, you can still use the remote control to

operate it.

Press once when the Robot is operating, it will become standby.

* Under the Standby Mode, the Robot will stop the current task.

Sweep At Fixed

Points

Press to enter Fixed-point Cleaning Mode, it will perform vacuum spirally with a 1.5m in diameter

around the current Robot location.

* Under this mode, the Robot will vacuum with a increasing radius and then a decreasing radius till back to the original

starting point.

Recharge Press once, enter Recharge Mode.

Start/Pause

Press once in Standby Mode, enter the Auto-vacuum Mode.

(clean in Zigzagging way rst and then along the wall)

Press once in any clean mode, enter the Standby Mode.

Suction Regulation Press to adjust the suction level.

Standard: Max:

Time Settings

Press when the Robot is powered on, the time on the display screen will blink, and then you can

select the time you want by pressing .

Press or to switch the time for minute adjustment.

Press or to save your settings.

Sweep Along the

Wall

Press once, enter the Along-wall Clean Mode, the Robot will clean along the wall.

* After along-wall cleaning is nished, the Robot will enter the Recharge Mode automaticaly.

Appointment

Settings

Press with the Robot on, icon and the time on the display screen will blink, and you can press

for hour adjustment.

Press or to switch the time for minute adjustment.

After settings are completed, press or to save it.

Press and hold to cancel the appointment settings.

• When controlling the Robot remotely with its Remote Control, stay within the infrared signal range of 7m or the Remote

Control may fail.

• When the Recharge Button is pressed, search may fail due to too complicated surrounding obstacles or the exhaustion of

the Robot's battery.

• As the infrared ray cannot surpass the wall, please operate the remote control within a visible scope.

12

Quick Start Guide

Preparation

Try to avoid using in the environment with stairs (if must, please set up a guardrail), and try to

remove the obstacles on the ground before use.

Install the Charging Base

Connect the supply cord into the power socket on the Charging Base. Please be careful to

organize the supply cord.

13

Connect the Power Supply to the Charging Base

Install the Charging Base in a location that the Robot can easily access. It is recommended

to place the Charging Base against a wall, and on a hard-level surface rather than on rugs or

carpets.

No obstacles 1.5m(4.92’) ahead

>0.5m(1.64′)

>0.5m(1.64’)

No obstacles 1.5m(4.92’) ahead

• In order to avoid external heat damage to the Charging Base, please do not place it next

toradiators,heaters,replaces,etc.

• Keep the Charging Base powered, or the Robot will not automatically returned.

Remove Shields

Beforeuse,removetheshieldsonbothsidesoftheFrontBumperandallprotectivelmson

both of the Robot and the Charging Base.

14

Place the Robot

Place the Robot on the Charging Base and align it with the Charging Electrodes. When the

chargingbaseindicatorontheChargingBasegoesoutandthepowerindicatorslow-ashes,

charging will begin.

Charging

You have two ways to charge the Robot.

Automatic recharging: the Robot will automatically return for recharging after the cleaning

task is completed.

Manual recharging:

Short press when pausing

to begin automatic recharging.

Short press

Short press when pausing

to begin automatic recharging.

when pausing to

begin automatic recharging.

• The Robot needs to be fully charged (approximately 5 hours) to ensure a normal

operation.

• IftheRobotisstuckedorcannotndtheChargingBase,pleasemanuallyputtheRobot

back to the the Charging Base.

15

Power On/off

Power on: • Press and hold the button for 4s on the operation panel.

• After the Robot is docking to the Charging Base, it will be powered on

automatically.

Power off: When the Robot is not in the Charging Base, press and hold the button for 4s

on the operation panel.

After power the Robot off, you cannot use the remote control to operate it.

Start Cleaning

Short press the button to start the Full-house Cleaning Mode.

Recommended start the Full-house Cleaning Mode when the Robot is on the Charging Base.

The Robot will leave the Charging Base and clean in Zigzagging way, and then clean the area

along the wall.

• Ifthebatterylevelistoolowtostartcleaning,pleasechargeitrst.

• Do not move the Charging Base during cleaning, and make sure that the Charging

Base is powered on, otherwise the Robot may not be able to return for charging.

16

Pause Cleaning

Pressing will pause the Robot while cleaning.

Pressing will stop the Robot while cleaning.

Sleep

Automatically switch to Sleep Mode:

• The Robot is inactive and the Charging Base is not connected for 10 minutes.

• There is no operation within 10 minutes after the Robot is fully charged.

Manually switch to Sleep Mode:

Press the button on remote control.

System Resetting

In Standby Mode, press and hold the + button for 15s to reset the system.

After resetting the system, the Robot will restore to factory settings.

Routine Maintenance

To maintain the best condition of the Robot, please maintain the Robot and replace parts with following frequencies:

Robot Part Maintenance Frequency Replacement Frequency

Side Brush Once every 2 weeks Every 3-6 months

Main Brush Once per week Every 6-12 months

High-performance Filter Once per week Every 3-6 months

Edge Sensor

Recharge Sensor

Cliff Sensor

Infrared Receiving Terminal

Front Bumper

Charging Electrode

Universal Wheel/Drive Wheel

Once per week /

• Before performing cleaning and maintenance tasks on the Robot, turn the Robot OFF and unplug the supply cord.

• A multi-function Cleaning Tool is provided for easy maintenance.Handle with care, this Cleaning Tool has sharp edges.

• EZVIZ manufactures various replacement parts and fittings. Please visit www.ezviz.com for more information on

replacement parts.

17

Dump the Dust Box

Press the Dust Box Taking-out Button to pull out the Dust Box, and then pour the dirt into dust

bin.

1

RemovetheFilteroutofthelterbox.

2

CleantheFilterwithCleaningToolandushtheFilterandDustBoxthroughlywithwateras

necessary, and then all cleaned elements shall be thoroughly dried.

Do not clean with hot water or detergent.

3

24H

18

Clean the Main Brush

Press the buckles to take out the Main Brush cover and the Main Brush.

1

Use the blade of the Cleaning Tool to cut off the hair entangled on the Main Brush and remove

the roller at one end of the Main Brush to clean it, and then re-install the Main Brush into

place.

2

19

Clean/Replace the Side Brush

Pull the side brush out and then clean the foreign matters like hairs.

Pull out the old side brush and then press the new one into the position.

Ezviz RC3 User manual

Popular Vacuum Cleaner manuals by other brands