FA Parkes 60129 User manual

Instruction Manual
Digital Electronic Combination Lock
Locking/Unlocking
To Unlock
1. Enter factory default passcode 1234 + OK or enter factory default Management Passcode 4321 + OK.
2. Long beep will sound.
3. Green indicator light will come on
4. Rotate the knob 90°within 3 seconds to open the lock. If the wrong passcode is entered, a beep will sound 3 times.
5. If lock shows red light this indicates low battery level.
NOTE: When entering Management Passcode to unlock, user passcode will be changed back to default 1234.
To Lock
1. Rotate the knob back to lock position.
1. Change passcode
1. Enter current User Passcode + OK, or Management Passcode + OK . Long beep will sound and will be
displayed.
2. Press OK for at least 2 seconds, then will flash.
3. Input new passcode, press OK. When you hear a long beep passcode has been changed.
NOTE: Passcode can consist of 4-15 digits. Management Passcode and User Passcode can not be the same code.
2. Turn on public mode, set temporary password
1. Enter current Management Passcode +OK , a long beep will sound and Unlocking indicator light will be
displayed
2. Press OK for at least 2 seconds, Unlocking indicator light will flash. Press OK again.
3. Input “4 4” and press OK. When you hear a long beep public mode has been set.
‘Unlocked’ indicator light
KEYPAD
BATTERY COMPARTMENT
USB KEY INTERFACE
‘Low power’ indicator light
HOW TO OPERATE
Page 1
SETTINGS
Part No. 60129

Set temporary password
1. Press OK . Unlocking indicator light will flash.
2. Enter the new passcode consisting of between 4-15 digits.
3. Press OK to unlock and a long beep will sound to indicate temporary passcode has been set.
NOTE: If Unlocking indicator light flashes once every 3 seconds indicates the passcode has already be taken.
Temporary passcodes can only be used once.
3.
1. Enter current Management Passcode +OK, a long beep will sound and Unlocking indicator light will be
displayed
2. Press OK for at least 2 seconds, Unlocking indicator light will flash. Press OK again.
3. Input “4 3” and press OK. When you hear a long beep public mode has been set.
4.
1. Enter current Management Passcode + OK, a long beep will sound and Unlocking indicator light will be
displayed.
2. Press OK for at least 2 seconds, Unlocking indicator light will flash. Press OK again.
3. Enter “4 2” then press OK, If you hear a long beep sound, Fake Pin code mode has been turned on.
Enter “4 1” then press OK
Page 2
Order online at
www.faparkes.co.uk
Your One-Stop-Shop for all your hardware requirements!
1. If the passcode has been forgotten, you can get the decode number by providing the code on the lock body to the
distributor to decode.
The passcode will be changed back to the original management passcode 4321 , user passcode 1234.
When the user passcode been forgotten, you can input the master passcode.
The user passcode will be changed back to the original user passcode.
2. Introduced with Anti-Theft Technology and Fake PIN passcode function; you can input any code(s) before or after
the real passcode to prevent the real passcode being peeped. Maximum 16 digits
3. Auto-alarm will be activated when input wrong password 4 times and the lock will be died for 60 seconds.
4. Automatic power shortage prompts (When lock show this signal The lock cannot be operated when the voltage is
very low
5. Equipped with 3V Cr2032 batteries, last password will not be lost after changing the battery.
Featuring Anti-Theft Technology and Fake PIN passcode function you can input any code(s) (maximum of 16 digits)
before or after the real password to prevent the real password being seen.
TROUBLESHOOTING
FEATURES
Problem Primary cause Resolution
When entering the passcode, alarm beeps twice while flashes once. Power is too low. Replace batteries.
When entering the passcode, alarm beeps while is displayed and lock
cannot be opened.
Knob is in incorrect
position.
Turn knob to correct
position.
Pressing keypad but no sound. Lock can be opened. Buzzer is damaged/
broken.
Replace buzzer.