FAAFTECH FT-RC-AUD10 User manual

Installation Manual
FT-RC-AUD10
REV 080617

1
• Congratulations for purchasing the video interface FT-RC-AUD10.
• Please, read this manual with attention before installing your new device.
• Keep this manual with you to check the functioning procedures and the
security information.
• We recommend that a professional, with experience in the field of installation
of vehicle devices, is the one to install this interface.
• The car ignition must be off during the entire installation process.
CHARACTERISTICS
• Enables 1 rear camera input
• Enables 1 front camera input
• Enables 1 auxiliary video input
• Dynamic parking lines
• 12V output to power the accessories
• Plug and Play Connections
• 1-year warranty against manufacturer defect
• Compatible vehicles: www.faaftech.com/produtos/interface-de-vid-
eo/ft-rc-aud10
PRESENTATION

INSTALLING
2
Follow the steps below to install the FT-RC-AUD10 interface:
1st Remove the original radio and the steering wheel’s column finish to install
the interface;
2nd Setup the interface’s DIP Switches according to the chart on “DIP SWITCH-
ES” section;
3rd Connect the whips according to the “CONNECTIONS” section;
4th Install the rear camera(s) and/or front camera according to the chart on the
“VIDEO CONNECTIONS” section.
Setup the interface’s DIP Switches while the device is disconnected from the
whip and the car ignition is off.
DIP SWITCHES
ON
1 2
DIP 1
SETUP DIP SWITCHES
UP for cars with a 7”or an 8” screen
DOWN for cars with a 5,8”screen
UP enables front camera
DOWN disables front camera
DIP 2

CONNECTIONS
3
Bridge on the radio’s
LVDS PINK or GREY
plug
Modelo: FT-RC-AUD10
Versão: xx
S/N: xxxxxxxxxx
VIDEO
IN/POWER
LVDS
IN/OUT
CAN/POWER
IN
DIP
SELECT
UPDATE
Connect to the steering
wheel’s column connector
*Remove the steering wheel
column’s finish to find the location
for installing
Note: on the FT-RC-AUD10
kit, there are 2 whips with
dierent connectors. Check
on the car connector which
one of the whips will plug in
the right way.
Connect to the
original whip
Connect to the nega-
tive
Connect to the 12V
Straight
Amarelo
Preto
Chicote A

*Cameras sold separately.
VIDEO CONNECTIONS
4
Connect a video source, such as a TV
or a screen mirroring
ONote: the audio must be connected
directly to the multimedia auxiliary entry
*Front Camera
*Rear Camera
Modelo: FT-RC-AUD10
Versão: xx
S/N: xxxxxxxxxx
VIDEO
IN/POWER
LVDS
IN/OUT
CAN/POWER
IN
DIP
SELECT
UPDATE
Camera Traseira
Rear Camera
Entrada de Vídeo
Vídeo Input
Camera Frontal
Front Camera
Saída GND
GND Output
Saída ACC
ACC Output
Use the ACC output and the GND output to power
the cameras, and the TV or the mirroring, if those are installed.

The parking lines do not offer 100% precision on the track they show. Use
them only as an auxiliary resource as you park your vehicle.
Important Notice:
5
Rear Camera
Once you put your vehicle on reverse, the rear camera will automatically show
on the screen.
As you spin the steering wheel, the parking lines will move, showing the vehi-
cle’s approximate direction as you keep going.
FUNCTIONING
Front Camera
When you put the car on reverse,
then switch the gear to N or D, the
front camera will automatically
appear on the screen. The camera
will remain turned on for 30
seconds, or until the car reaches the
speed of 15 km/h (9.32 mph) or if
you press the OK button on the
steering wheel (see image of the OK
button on the next page).

ACCESSING THE AV INPUTS
Follow the steps bellow to access the interface’s AV entry:
• Select the AUX audio source from the multimedia;
• Press and hold the OK button on the steering wheel to gain access to the inter-
face’s AV mode;
• If you have installed a front camera, simply click the OK button to alter between
the AV input view and the front camera;
• Press and hold the OK button on the steering wheel to return to the original
menu.
6
FUNCTIONING
OK button
on the steering wheel

[phone] or [phone]
[email protected]
www.faaftech.com.br
Available from Monday to Friday, from 8 a.m. to 6 p.m. Brasilia time
TECHNICAL SUPPORT Follow us on social media