Faber FCB 1030 User manual

FOOD PROCESSOR
INSTRUCTION MANUAL
FCB 1030
Read this booklet thoroughly before using and save it for future reference

1
IMPORTANT SAFETY INSTRUCTIONS
·Read all instructions before using.
·Do not open until blades stop.
·The attached motor unit can not be used for other than intended use.
·Unplug from the outlet when not in use and before cleaning. Allow to cool before
putting on or taking off parts, and before cleaning the appliance.
·Do not let the cord hang over the edge of a table or counter or touch a hot surface.
·Do not place on or near a hot gas or electric burner or in a heated oven.
·keep hands and utensils away from the cutting blade while chopping food to
reduce the risk of severe injury to persons or damage to the food chopper. A
scraper may be used but only when the food chopper is not running.
·To protect against a fire, electric shock or personal injury, do not immersecord,
electric plugs, or motor unit in water or other liquids.
·Close supervision is necessary when any appliance is used by or near children.
·The appliance is not a toy. Do not let the children play it.
·Avoid contacting moving parts.
·The use of attachments not recommended or sold by manufacturer may cause
fire, electric shock or injury.
·Do not operate any appliance with a damaged cord or plug or after the appliance
malfunctions, or is dropped or damaged in any manner, Return appliance to the
nearest authorized service facility for examination,repair or electrical or
mechanical adjustment.
·Do not use the appliance for other than intended use.
·Be sure motor unit is locked securely in place before operating appliance.
·Do not attempt to defeat the lid interlock mechanism.
·Do not use outdoors.
·If the supply cord is damaged, it must be replaced by the manufacturer, its
service agent or similarly qualified persons in order to avoid a hazard.
·Always disconnect the appliance from the supply if it is left unattended and
before assembling, disassembling or cleaning.
·Appliance can be used by persons with reduced physical, sensory or mental
capabilities or lack of experience and knowledge if they have been given
supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved.
·Children shall not play with the appliance.

2
·Appliance shall warn of potential injury from misuse.
·This appliance shall not be used by children.Keep the appliance and its cord out
of reach of children.
·Care shall be taken when handling the sharp cutting blades, emptying the bowl
and during cleaning.
·SAVE THESE INSTRUCTION.
DO NOT OPEN UNTIL BLADES STOP.
HOUSEHOLD USE ONLY
KNOW YOUR FOOD CHOPPER
Switch button
Motor unit
Bowl cover
Sblade
Blade sheath
Bowl
Bowl mat

BEFORE THE FIRST USE
Before using this appliance for the first time, wash the bowl and blade assembly in
sudsy water and dry thoroughly, all of these parts are safe in dishwasher, wipe the
motor unit with a damp cloth, do not immerse the motor unit in water.
HOW TO CHOP OR MINCE FOOD
1. Place the bowl on a counter or other flat surface, then slide the blade down
over the shaft in the bowl. Be careful not to touch the blade as it is extremely
sharp.
2. Place food in the bowl, the desired food refers to the chopping guide.
3. Place the bowl cover onto the bowl then position the motor unit onto the bowl,
the embossment on the bowl cover is linked up to the hole on the motor unit,
lining up the motor unit locking tabs to the bowl locking slots till the motorunit
locks.
4. Pulg the power cord, the left hand hold the motor unit, then the right hand
depress and hold the pulse button to process.
Note: This product has a pulse button. Avoid running the motor continuouslyin
this mode for period over 30s. the longer the continuous pulse, the finer the
texture. For coarsely chopped foods, use short pulses.
5. Be sure the blade stops rotating completely before removing the bowl cover.
Unplug the unit. Remove the motor unit and grasp the plastic blade hub.
carefully pull the blade assembly out. Remove the bowl and empty the
processed food. Do not use bowl for storing food.
CLEANING AND MAINTENANCE
Always disconnect the appliance from the power outlet before cleaning.
Wash the bowl, blade assembly immediately after use either with warm/sudsy
water or in the dishwasher. Wipe off the motor unit with a damp cloth- do not
immerse in water.
NOTE: Do not use chemical, steel, wooden or abrasive cleaners to clean the unit
to prevent the gloss loss.
3

4
CHOPPING GUIDE
Food type Operation guide
Bread
Shred proper amount of bread into small pieces, it is
recommended to use speed2 pulse to chop, work for 10
seconds, rest for 1 minute for one cycle, and perform
several cycles of operation until a satisfactorychopping
effect is achieved;
Fruits and Vegetables
(canned, cooked)
Put up to 120g of food, it is recommended to use
speed2 pulse to chop, work for 10 seconds, rest for 1
minute for one cycle, and perform several cycles of
operation until a satisfactory thick slurry effect is
achieved;
Fresh celery and
other leafy plants
Put a proper amount of food to be thoroughly cleaned
and dry, it is recommended to use speed2 pulse to chop,
work for 10 seconds, rest for 1 minute for one cycle, and
perform several cycles of operation until a satisfactory
chopping effect is achieved;
Nut
Cookies, cookies
Put up to 120g of food, it is recommended to use
speed2 pulse to chop, work for 10 seconds, rest for 1
minute for one cycle, and perform several cycles of
operation until a satisfactory thick slurry effect is
achieved;
Put up to 120g of food, it is recommended to use
speed2 pulse to chop, work for 10 seconds, rest for 1
minute for one cycle, and perform several cycles of
operation until a satisfactory thick slurry effect is
achieved;
Fresh beef
Honey,maltose
60mm*20mm*20mm
size block
Put up to 120g of food, it is recommended to use
Put in 50 grams of honey and 50 grams of maltose, it
is recommended to use speed 2 pulse to chop, work for 5
seconds,rest for 1 minute for one cycle, and perform
several cycles of operation until a satisfactory thick slurry
effect is achieved;
speed2 pulse to chop, work for 10 seconds, rest for 1
minute for one cycle, and perform several cycles of
operation until a satisfactory thick slurry effect is
achieved;

5