Faber LI_991.0426.991 User manual

Instructions Manual
Manuel d’Instructions
Bedienungsanleitung
Manual de instrucciones
Εγχειρίδιο οδηγιών
Руководство по эксплуатации
Kullanim Kilavuzu

2
2
INDEX
RECOMMENDATIONS AND SUGGESTIONS ..................................................................................................................... 4
CHARACTERISTICS ............................................................................................................................................................. 7
INSTALLATION...................................................................................................................................................................... 9
USE ...................................................................................................................................................................................... 19
MAINTENANCE................................................................................................................................................................... 21
SOMMAIRE
CONSEILS ET SUGGESTIONS.......................................................................................................................................... 23
CARACTERISTIQUES......................................................................................................................................................... 26
INSTALLATION.................................................................................................................................................................... 28
UTILISATION ....................................................................................................................................................................... 38
ENTRETIEN......................................................................................................................................................................... 40
INHALTSVERZEICHNIS
EMPFEHLUNGEN UND HINWEISE ................................................................................................................................... 42
CHARAKTERISTIKEN......................................................................................................................................................... 45
MONTAGE ........................................................................................................................................................................... 47
BEDIENUNG........................................................................................................................................................................ 57
WARTUNG........................................................................................................................................................................... 59
INDICE
CONSEJOS Y SUGERENCIAS........................................................................................................................................... 61
CARACTERÍSTICAS ........................................................................................................................................................... 64
INSTALACIÓN ..................................................................................................................................................................... 66
USO...................................................................................................................................................................................... 76
MANTENIMIENTO............................................................................................................................................................... 78
ΠΕΡΙΕΧΟΜΕΝΑ
ΣΥΜΒΟΥΛΕΣ ΚΑΙ ΣΥΣΤΑΣΕΙΣ............................................................................................................................................ 80
ΧΑΡΑΚΤΗΡΙΣΤΙΚΑ............................................................................................................................................................... 83
ΕΓΚΑΤΑΣΤΑΣΗ.................................................................................................................................................................... 85
ΧΡΗΣΗ ................................................................................................................................................................................. 95
ΣΥΝΤΗΡΗΣΗ........................................................................................................................................................................ 97
УКАЗАТЕЛЬ
СОВЕТЫ ИРЕКОМЕНДАЦИИ .......................................................................................................................................... 99
ХАРАКТЕРИСТИКИ.......................................................................................................................................................... 102
УСТАНОВКА...................................................................................................................................................................... 104
ЭКСПЛУАТАЦИЯ.............................................................................................................................................................. 114
УХОД.................................................................................................................................................................................. 116
EN
FR
DE
ES
GR
RU

3
3
IÇERIKLER
TAVSIYELER VE ÖNERILER............................................................................................................................................ 118
ÖZELLIKLER...................................................................................................................................................................... 121
MONTAJ............................................................................................................................................................................. 123
KULLANIM ......................................................................................................................................................................... 133
BAKIM ................................................................................................................................................................................ 135
TR

EN 4
4
RECOMMENDATIONS AND SUGGESTIONS
The Instructions for Use apply to several versions of this appliance.
Accordingly, you may find descriptions of individual features that do not
apply to your specific appliance.
INSTALLATION
• The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation.
• The minimum safety distance between the cooker top
and the extractor hood is 650 mm (some models can
be installed at a lower height, please refer to the
paragraphs on working dimensions and installation).
• Check that the mains voltage corresponds to that
indicated on the rating plate fixed to the inside of the
hood.
• For Class I appliances, check that the domestic
power supply guarantees adequate earthing.
Connect the extractor to the exhaust flue through a pipe of minimum
diameter 120 mm. The route of the flue must be as short as possible.
• Do not connect the extractor hood to exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction with non-
electrical appliances (e.g. gas burning
appliances), a sufficient degree of aeration must
be guaranteed in the room in order to prevent the
backflow of exhaust gas. The kitchen must have
an opening communicating directly with the open
air in order to guarantee the entry of clean air.
When the cooker hood is used in conjunction with
appliances supplied with energy other than electric, the negative pressure in
the room must not exceed 0,04 mbar to prevent fumes being drawn back
into the room by the cooker hood.
• In the event of damage to the power cable, it must be replaced by the
manufacturer or by the technical service department, in order to prevent any
risks.
2°

EN 5
5
• If the instructions for installation for the gas hob specify a greater distance
specified above, this has to be taken into account. Regulations concerning
the discharge of air have to be fulfilled.
• Use only screws and small parts in support of the hood.
Warning: Failure to install the screws or fixing device in accordance with
these instructions may result in electrical hazards.
• Connect the hood to the mains through a two-pole switch having a contact
gap of at least 3 mm.
USE
• The extractor hood has been designed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes other than for which it has been designed.
• Never leave high naked flames under the hood when it is in operation.
• Adjust the flame intensity to direct it onto the bottom of the pan only, making
sure that it does not engulf the sides.
• Deep fat fryers must be continuously monitored
during use: overheated oil can burst into flames.
• Do not flambè under the range hood; risk of fire.
• This appliance can be used by children aged from
8 years and above and persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.

EN 6
6
• “CAUTION: Accessible parts may become hot when used with cooking
appliances.”
MAINTENANCE
•Switch off or unplug the appliance from the mains supply before carrying out
any maintenance work.
• Clean and/or replace the Filters after the specified time period (Fire hazard).
• The Grease filters must be cleaned every 2 months of operation, or more
frequently for particularly heavy usage, and can be washed in a dishwasher.
• The Activated charcoal filter is not washable and cannot be regenerated,
and must be replaced approximately every 4 months of operation, or more
frequently for particularly heavy usage.
• "Failure to carry out cleaning as indicated will result in a fire hazard".
• Clean the hood using a damp cloth and a neutral liquid detergent.
The symbol on the product or on its packaging indicates that this product
may not be treated as household waste. Instead it shall be handed over to the
applicable collection point for the recycling of electrical and electronic
equipment. By ensuring this product is disposed of correctly, you will help
prevent potential negative consequences for the environment and human
health, which could otherwise be caused by inappropriate waste handling of
this product. For more detailed information about recycling of this product,
please contact your local city office, your household waste disposal service or
the shop where you purchased the product.

EN 7
7
CHARACTERISTICS
Components
Ref. Q.ty Product Components
11 Hood Canopy complete with: Controls, Light, Filters,
Motor.
21 Intermediate Hood Canopy
31 Ceiling mounted Hood Canopy
41 Hood support plate + Flange
51 Upper Hood canopy panel
61 Pipe
73 Clamps to fix the Power Cable
Ref. Q.ty Installation Components
11 7 Wall plugs ø 10
12a 7 Screws 4.2 x 44.4
12b 3 Fixing knobs
12c 4 Screws 3.5 x 9.5
Q.ty Documentation
1 Instruction Manual
6
7

EN 8
8
Dimensions

EN 9
9
INSTALLATION
This hood is designed to be mounted on the ceiling/on a shelf, above a free-standing Hob (min. 650
mm), in:
• Ducting version: Evacuation to the outside.
Sequence of operations - Installation
• Preparing for installation
• Drilling the Ceiling/Shelf and Fixing the support plate
• Connections
• Fitting the hood body
• Functional Check
• Disposal of Packaging
Preparing to fit the Plate
• Take the Plate and position it the right way round, as shown in the figure.
The pawl must face towards the installer.

EN 1
10
Ceiling/Shelf drilling and Plate Fixing
CEILING/SHELF DRILLING
• Use a plumb-line and mark the centre of the cooking hob on the Support Ceiling/Shelf
• Rest the Plate against the Ceiling/Shelf, making sure it is the right way up, as shown in the
figure.
• Mark the centres of the holes in the plate.
• Drill the following points:
• Ceilings in solid concrete: As per concrete plugs used.
• Ceilings in hollow bricks with 20 mm resistance thickness: Drill a hole ø 10 mm (insert
Plugs 11 supplied immediately).
• Ceilings with Wood Beams: As per Wood Screws used (not supplied).
• Wooden shelf, with a resistant thickness of 15 mm: drill a hole ø 7 mm.
• Feeding the electric supply cable: drill a hole ø 10 mm.
• Insert two screws, crossing them and leaving 4-5 mm from the ceiling:
• for solid concrete, concrete plugs, not provided.
• for hollow bricks with approx. 20 mm resistance thickness, screws 12h, provided.
• for wooden beams, wood screws, not provided.
• for wooden shelves, screws with washers and nuts, not provided.

EN 1
11
FIXING (HOOD CANOPY + INTERMEDIATE HOOD CANOPY)
• Insert the Hood Canopy
1into the Intermediate
Hood Canopy 2.
• Take the upper Hood Canopy Panel 5and
insert it as shown in the figure.
Warning!
the upper Hood Canopy Panel 5must be
inserted first on one side and then on the other,
using the rounded edges and taking care not to
damage the Cables that have to pass through
the slots provided.
• Lower the panel until it rests
on the Hood Canopy 1, then
fasten it in place with the 4
screws 12c provided.
1
2
12c
ab
1
2
5

EN 1
12
FIXING THE PLATE
• Lift up the Fixing plate and fit the slots onto the two
screws previously inserted in the ceiling, and turn un-
til they are at the centre of the adjustment slot.
Warning: The plate must be facing in the direction
shown in the figure
• Tighten the two screws completely and screw in the
other two provided; before locking the screws
completely it is possible to make adjustments by
turning the piece, making sure that the screws do not
come out of the adjustment slot.
• The unit must be securely fastened both due to the
weight of the Hood and the stress caused by
occasional sideways pressure on the Appliance when
in position. Once the unit has been fixed, make sure
that the plate is stable.
• In all cases where the Ceiling is not sufficiently
strong at the point of suspension, the Installation
technician must strengthen it with suitable plates and
counterplates, anchored to structurally sound
elements.
• Check that the plate is level on the ceiling.
• Should it be considered advisable, the hood can be
fixed to the wall using 3 more screws and wall plugs.

EN 1
13
CONNECTING HOOD-PLATE CABLES
N.B.Before proceeding with installation the Hood must be raised to a height of at
least 650 mm above the cooker hob by means of a support or with the assistance
of another person.
This operation is essential, as the Hood Cables are to be connected to the Plate mounted
on the ceiling, and this must be done without the weight of the Hood bearing down on
the structure.
The system used to fix the 4 Cables comprises 3 components:
• Threaded pawl (a) already mounted on the ceiling Plate.
• Cable locking screw (b), provided.
• Safety knob (c), provided.
• Insert the safety knobs (c) into the respective
cables, with the thread to the top.
• Insert the cable locking screws (b) into the
respective cables.
• Pay attention to the direction in which the Plate is fixed to the
ceiling (the Plate limit pawl has a corresponding hole on the
Hood canopy).
Warning: The
maximum
extension for
movement of
the Hood
must not
exceed
645mm.
a
b
c

EN 1
14
• Pass the Cables into the slots on the threaded pawls (a) and
tighten the cable locking screws (b) into the pawls
themselves.
• When the operation has been
completed, the result should be as
shown in the figure for all 4
cables.
• At this point, all 4 cables are now
connected to the Plate.
Tension the Cables by pushing them
upwards, so that they slide inside the
cable locking screw and out through the
slot in the threaded pawl.
This is possible because the cable
locking screw involves a system that
allows the Cable to slide in one direction
only, preventing it from sliding in the
other direction.
Make sure that the Cables are all the
same length, to facilitate final levelling
operations. The left front cable must not
be slacker than the others.

EN 1
15
LEVELLING THE HOOD
• The hood canopy must be levelled.
• The Hood is levelled by adjusting the
safety pawls C.
• Rest a spirit level on the hood.
• Exerting an upwards pressure on the safety knobs
“unlocks” movement of the Cable. By inserting or
extracting the cable from the cable locking screw
it is possible to make adjustments to level the
mobile hood canopy.
• Once the hood has been set level, the safety knobs
must be tightened.
Warning:
• Make sure that all 4 of the support cables are taut.
• Make sure that none of the 4 support cables have been damaged during installation.
• Remember that there must be a minimum distance of 650mm between the Hood and the cooker
hob and the maximum extension of movement must not exceed 645mm.

EN 1
16
FIXING THE POWER SUPPLY CABLE
• Take the Power Cable coming from the wiring
box and clamp it with the cable clamps 7first to
the right rear cable (A) and then to the left cable
(B) as shown in the figure.
• Run the power cable up to the
plate on the ceiling.
• Slot the rubber cable raceway
already threaded onto the power
cable into the slot to prevent
future damage.
• Fix it to the bracket on the
ceiling plate, using the tongue
already fitted.
• Connect the Hood to the Mains
Power Supply, inserting a
bipolar switch with a contact
aperture of at least 3 mm.
Finally, check that the power supply cable is properly locked, checking that when the mobile
unit rises up towards the ceiling, it positions itself over the mobile unit and does not come out
from the edge of the hood.
7
A
B

EN 1
17
Connections
AIR OUTLET - DUCTING VERSION
To install in Ducting Version, connect the hood to the
outlet pipe by means of an extending pipe ø150.
• Fix the pipe both to the Hood Canopy and to the
Flange on the Ceiling plate, using suitable pipe
clamps. The materials required to do so are provided.

EN 1
18
FIXING (Intermediate Hood Canopy + ceiling
mounted Hood Canopy)
• Carry out tests to check that the Hood works (see
paragraph on Use).
• From below, insert the ceiling mounted Hood
Canopy 3into the part of the Hood Canopy hanging
from the ceiling, making sure the direction is as
shown in the figure.
• Using the 3 Screws 12b provided, fix the ceiling
mounted Hood Canopy 3to the Plate on the ceiling.
3
12b

EN 1
19
USE
Control panel
L T1
Button Function Display
L Turns the lights On/Off. -
T1 Hood Down
Press for 2 seconds to raise the Hood.
Press briefly to turn the Motor On/Off.
On/Off
Hood Up
Press once: The Hood lowers.
Press a second time: The Hood Stops.
When the movement has been completed
the motor turns on at Speed two.
Off/Off
The electronic control system recognises and signals two types of fault.
Led T1
Slow flashing
Current absorption threshold exceeded:
If an overload condition occurs, the fault is signalled by LED T1 on the
keyboard flashing once every 2 seconds. Check that nothing is blocking
normal hood movements.
The signal remains active until a new hood open/close command is given.
Rapid flashing
Hood opening safety microswitch tripped:
If the safety microswitch trips, the fault is signalled by LED T1 on the
keyboard flashing quickly (once every 250 ms). This means that the hood
has passed the microswitch…….. Call Technical Assistance!
You can continue to use the hood’s light and motor functions while this
fault is active. Whenever the motor is on, LED T1 will continue to flash,
indicating that the fault is still present.

EN 2
20
REMOTE CONTROL
The appliance can be controlled using a remote control powered by
a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA
type (not included).
• Do not place the remote control near to heat sources.
• Used batteries must be disposed of in the proper manner.
Control panel
Button Function Display
Turns the Motor On/Off. -
Hood Closed:
- Press the button briefly to start lowering the hood
- It will stop when the button is pressed again.
When the movement has been completed the motor will start at speed 2.
-
Hood Open:
- Press and hold for 2 seconds to activate raising of the hood, which stops when it reaches the stop.
- Press (briefly) to stop the movement (before the stop is reached).
- Press again briefly to turn the motor on/off.
- Press and hold for 2 seconds to start raising of the hood.
- If the motor is on, it will first stop the motor and then start the movement.
-
Decreases the speed of the Motor. -
Increases the speed of the Motor. -
INTENSIVE
- This can only be activated with the hood lowered and when the delay or 24h functions are not active.
- Activates Intensive speed from any other speed.
To disable it, simply press the same button again or turn the motor off.
- Intensive speed is timed to run for 10 minutes. At the end of the 10 minutes the system will automati
cally return to the speed that was set before.
The led on the motor
button (on the hood
controls) will flash
once a second.
Press briefly for the Delay Function:
Can only be activated if the Intensive or 24h function is not active.
Activates and deactivates total shutdown of the hood (motor+lights) after 30 minutes:
To disable the Delay, simply press the button again or turn the motor off.
The led on the motor
button (on the hood
controls) will flash
once every 0.5 sec-
onds.
Press and hold for 2 sec. for the 24H Function:
Can only be activated if the Intensive or Delay function is not active.
Activates and deactivates the 24H function for 10 minutes every hour, for 24 hours. After this time it is
deactivated.
The led on the motor
button (on the hood
controls) will flash
once every 2 seconds.
Turns the Hood lights On/Off.