Faber Velvet Operating and safety instructions

For recirculating installations, high
quality, heavy duty filters ensure
the removal of smoke and odors
from the kitchen. Some ductwork is
required to exhaust the unit out of
the cabinet.
Charcoal Filters FILTER1
For a streamlined look in the kitchen, the Glass and Stainless
Steel Velvet is your high end integrated solution. The Velvet
has a sleek glass pull-out visor which slides in, flush with your
cabinets, neatly tucking the hood away. The rangehood turns
on and off automatically when the visor is pulled in and out.
glass & stainless slideout rangehood
slim styling
microswitch turns motor/lights
on when pulled out
closes flush with cabinets
easily replaces existing hoods
600 cfm PRO motor
2 halogen lights + dimmer light
4 speed electronic controls
intensive boost mode
perimetric suction system
silent kit sound reduction
dishwasher safe grease filters
top or direct rear venting
convertible to recirculating
grease filter alarm
built-in mounting system
sone range: 3.5 - 6.5
6” round duct
Size/Color/Model #
30 Glass & Stainless
36 Glass & Stainless
°
°
°
°
°
°
°
°
°
°
°
°
°
°
°
°
°
°
VELV30SS
VELV36SS
a
c
c
e
s
s
o
r
i
e
s
p.o. box 435 • Wayland, MA 01778 • tel: [phone] • fax: [phone] • e-mail: [email protected] • www.faberonline.com
Velvet
sleek undercabinet glass slide out hood
Integrated Collection
For use in make up air environments where
an under 300 cfm hood is required. This
kit reduces the ducting to 5” round and
reduces the cfm to under 300
CFMRED
CFM Reducer Kit
LED Electronic touch controls

Dimensional Diagrams
Rev.07/11
WARNING! Product specifications are subject to change without notification. Consult the installation instructions
before you begin installing this rangehood.
Make your ductrun as straight and
short as possible. The ductrun
should not exceed 35 equivalent feet
if ducted with the required minimum
of 6” round duct. Count 45º angles
as 3 feet, 90º elbows as 5 feet, and
90º flat elbows as 12 feet.
For best results, use no more
than three 90° elbows. Make sure
that there is a minimum of 24”
of straight duct between elbows
if more than one is used. Do not
install two elbows together. If you
must elbow right away, do it as
far away from the hood’s exhaust
opening as possible.
For more efficient airflow when
venting to the rear: Rotate the
Cristal HC blower housing so that
the 6” round exhaust outlet faces the
back, rather than running ductwork
up and elbowing back.
Pre-Planning Your Ductwork - Important: Consult the installation instructions before you begin installing this rangehood.
Recirculating Installations
Some ductwork must
be installed to exhaust
the rangehood back
into the kitchen, either
atthetopofthe cabinet
or at the face of the
soffit. Use a plastic
vent grate to cover
the duct opening. This
duct work must not
terminate into a dead
air space.
Front View
For installations where ductwork to the outside of your home is impossible or highly impractical
Charcoal Filters, which attach to the blower assembly, absorb smoke and odors.
cabinet
ceiling
6” round
duct
hood
cabinet
ceiling
6” round
duct
hood
soft
vent grate
vent grate
Pre-Planning Your Installation - Important: Consult the installation instructions before you begin installing
this rangehood. The recommended height to install this hood off the cooktop is a minimum of 24” and a maximum of 30”
for maximum effectiveness. Also consult the cooktop manufacturer’s recommendation.
Cut-Out
9 3/4”
25 1/4” - 31 1/4”