Fabritec designs Sonesse (Ultra Quiet) 506 Motor User manual

page 1 of 4
SONESSE (Ultra Quiet)
506 MOTOR
INSTALLATION INSTRUCTIONS
SONESSE (Ultra Quiet) 506
MOTORS
INSTALLATION INSTRUCTIONS
Thank you for purchasing your new Sonesse (Ultra
Quiet) 506 Motor. They have been custom-made from
the highest quality materials to the dimensions you
specied. With the proper installation and care, it will
provide you with many years of beauty and trouble-
free use.
Please read all instructions before you start so you will
be familiar with the overall process.
Make sure you measure your window to ensure the
motors and shades will t properly before beginning.
Getting Started
Remove the motor and shade from the packaging.
Keep the packaging until you have successfully installed the
motorized shade.
PLEASE NOTE:
This is a very powerful heavy motor and the brackets have
to be secured and attached to wood studs.
FASTENERS CANNOT BE USED!
Often, wood headers are found above the windows. If this
is not possible, and you can’t secure the shade brackets to
the wood studs, then plan on using a Headbox.
Headbox brackets can be located and attached to the
wood studs.
• Pencil • Power Drill with the following bits:
• Awl - ¹⁄₁₆” Drill Bit
• Tape Measure - ¹⁄₄” Hex Driver
• Level - Standard Screwdriver
• Ladder or Stepstool - Masonry Drill Bit (if drilling into concrete
or brick)

page 2 of 4
BEFORE YOU BEGIN, VERIFY THAT YOU HAVE ALL THE NECESSARY
PARTS AND PIECES:
• PACKAGE - Contains an idler end bracket and a motor end
bracket, one retainer clip, one idler ring spacer and four
installation screws.
Mounting the Brackets and Shade
STEP 1 - INSTALLING THE BRACKETS.
Note: There are two different brackets.
One for the idler end and one for the motor end. The idler
end bracket and motor end bracket can be used for wall,
ceiling, outside mount or inside mount installations.
The bracket to bracket dimension is the shade cloth width
plus 1⁷⁄₈”.
Use a level to ensure a horizontal position.
a) Install the idler end bracket rst.
STEP 1 - INSTALLING THE BRACKETS (continued).
b) Next, install and mount the motor end bracket.
See illustration below.
STEP 2 - INSTALLING THE IDLER END OF SHADE.
a) Begin by slipping the idler end spacer over the idler shaft
on the roller shade.
Make sure the spacer is snug and butted up against the
spring on the shaft.
Illustrations, clockwise from top left:
Motor end bracket, Idler end bracket, idler ring spacer
with plastic bag, installation screws and a retainer clip.
Idler End Bracket
Idler End Spacer inserted
properly and butted up
against spring on shaft
Motor End Bracket

page 3 of 4
STEP 2 - INSTALLING THE IDLER END OF SHADE (continued).
a) Place the idler end into the idler end bracket.
b) Push the shaft until it is completely collapsed and snug
against the idler end bracket.
STEP 3 - INSERT THE MOTOR END.
a) Slip the motor end into the bracket. Make sure the cord is
positioned toward the back of the bracket.
While keeping the idler end in position, lift the shade up
into the bracket easing the motor head into the motor
end bracket.
b) After installing the motor end, slip the retainer clip onto
the motor end. This prevents the motor from slippping out
of its bracket.
Make sure the retainer clip sits in the bracket channel.
See illustrations below.
Motor End
of shade
Retainer Clip
Retainer Clip
Seated Properly

page 4 of 4
Caring for your Sonesse (Ultra Quiet) 506
Motors & Roller shades
Your Sonesse (Ultra Quiet) 506 motors and roller shades will
provide you with years of beauty and pleasure with minimal
care and cleaning.
• Vacuum using a brush or dust head attachment.
• Dust lightly using a soft, clean cloth.
• Never immerse the motors or shades in water or liquids
of any type.
Note:
Call us at 800.828.2500 if you have any questions.
STEP 4 - CONNECT YOUR POWER SOURCE AND TEST THE
SHADE.
Please note, your shades are preset at the factory.
If limit adjustments are required, refer to the programming
instructions. These can be found in the remote controller
shipping box.
STEP 5 - MOUNT REMOTE CONTROLLER HOLDER.
a) Mount your remote controller holder to the wall.
b) Insert your remote contoller into the holder.
c) Congratulations, you are done!
AP1608S506MII© 2016 Fabritec, LLC.
Fabritec, LLC.
7531 Coldwater Canyon Avenue
North Hollywood, CA 91605
t) 818.503.8300
f) 818.503.8360
www.castec.com
www.fabritecdesigns.com