FAFREES FM9 User manual

Smart EV/Moped
User Manual
(Model: FM9)
EN DE FR IT ES

1-21
22-42
43-63
64-84
85-105

*Before your first operation,
please read the user manual carefully!
1. Note
Before your first ride, it is important for you to know your new e-bike well, so that you can
get the best performance, comfort, enjoyment and safety from it during your ride. To
understand the new bicycle and the correct operation, you should first read the manual
carefully.
Second, it is significant to take your first ride under a safe and controlled circumstance, like
staying away from cars, obstacles and other cyclists.
Third, bicycles are vehicles with certain risks. Please follow the traffic rules during cycling.
It's better to learn the local traffic rules about riding an e-bike on public roads before your
first ride in case you violate the regulations. For your own safety, never forget to put on a
qualified helmet before you get on the e-bike.
Fourth, the electric bike is supplied without basic mandatory equipment, which may vary
from place to place. Therefore, if you intend to use the e-bike on public roads, it's necessary
to equip the bike with the basic mandatory equipment, in accordance with the relevant laws
and regulations.
In addition, this product is designed for your personal use. Do not use it for commercial or
other purposes.
Last, keep this manual safe for reference.
2. Warning
Before each charge, check the charger, cable and plug. If there is any damage, do not use
the charger.
Before riding, check the tire pressure and check whether the wheels and handlebar are
installed correctly and tightly.
Before riding, check whether the headlights are securely fastened in the correct position,
clean and not covered by anything. Damaged reflectors must be replaced.
Besides, if the seat post in the seat tube is not inserted deep enough to reach the
minimum insertion mark, the seat post may break. Check whether it is inserted deeper
than the minimum insertion depth. When braking on a wet road, the braking distance is
usually longer than on a dry road. Therefore, brake earlier for a safer stop.
When you have to brake urgently, please hit the right hand brake first to stop the rear
wheel, and then hit the left hand brake, especially when you brake at a high speed. If the
front wheel stops suddenly while the rear wheel is still cycling at a high speed, you may
fall over and get hurt. So please ride it carefully.
Furthermore, avoid puddles, wet mud, swamps, water, snow or ice. Try not to use the
e-bike on a rainy, stormy or snowy day. If the bicycle's electric parts (control unit, engine
and battery) get damp, wet or soaked, it will cause irreversible damage, or even a battery
explosion.
This product can only be used by one adult at a time. Do not carry any extra passengers.
This vehicle is not a toy. Same as other vehicles, it is possible to fall, crash or encounter
other danger¬ous situations. Please don't offer your e-bike to anyone that doesn't know
how to use it correctly. If you let anyone else ride your bike, it will be your responsibility to
ensure that all riders understand all warnings, cautions, instructions and safety
precautions, and to ensure that they are able to use this product safely and responsibly
and protect themselves and others from injury.
1

43
21
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
1. Note
Before your first ride, it is important for you to know your new e-bike well, so that you can
get the best performance, comfort, enjoyment and safety from it during your ride. To
understand the new bicycle and the correct operation, you should first read the manual
carefully.
Second, it is significant to take your first ride under a safe and controlled circumstance, like
staying away from cars, obstacles and other cyclists.
Third, bicycles are vehicles with certain risks. Please follow the traffic rules during cycling.
It's better to learn the local traffic rules about riding an e-bike on public roads before your
first ride in case you violate the regulations. For your own safety, never forget to put on a
qualified helmet before you get on the e-bike.
Fourth, the electric bike is supplied without basic mandatory equipment, which may vary
from place to place. Therefore, if you intend to use the e-bike on public roads, it's necessary
to equip the bike with the basic mandatory equipment, in accordance with the relevant laws
and regulations.
In addition, this product is designed for your personal use. Do not use it for commercial or
other purposes.
Last, keep this manual safe for reference.
2. Warning
Before each charge, check the charger, cable and plug. If there is any damage, do not use
the charger.
Before riding, check the tire pressure and check whether the wheels and handlebar are
installed correctly and tightly.
Before riding, check whether the headlights are securely fastened in the correct position,
clean and not covered by anything. Damaged reflectors must be replaced.
Besides, if the seat post in the seat tube is not inserted deep enough to reach the
minimum insertion mark, the seat post may break. Check whether it is inserted deeper
than the minimum insertion depth. When braking on a wet road, the braking distance is
usually longer than on a dry road. Therefore, brake earlier for a safer stop.
When you have to brake urgently, please hit the right hand brake first to stop the rear
wheel, and then hit the left hand brake, especially when you brake at a high speed. If the
front wheel stops suddenly while the rear wheel is still cycling at a high speed, you may
fall over and get hurt. So please ride it carefully.
Furthermore, avoid puddles, wet mud, swamps, water, snow or ice. Try not to use the
e-bike on a rainy, stormy or snowy day. If the bicycle's electric parts (control unit, engine
and battery) get damp, wet or soaked, it will cause irreversible damage, or even a battery
explosion.
This product can only be used by one adult at a time. Do not carry any extra passengers.
This vehicle is not a toy. Same as other vehicles, it is possible to fall, crash or encounter
other danger¬ous situations. Please don't offer your e-bike to anyone that doesn't know
how to use it correctly. If you let anyone else ride your bike, it will be your responsibility to
ensure that all riders understand all warnings, cautions, instructions and safety
precautions, and to ensure that they are able to use this product safely and responsibly
and protect themselves and others from injury.
Product function illustration (Model: FM9)
1.Break lever
2.Shift lever
3.LCD display
4.Bell
5.Headlight
6.Fender
7.Brake pad
8.Brake caliper
9.Front fork
10.Pedal
11.Crankset
12.Controller
13.Chain
14.Rear derailleur
15.Tire
16.Rear light
17.Cargo rack
18.Saddle
19.Battery
2

1. Charging: Find the charging port on the side frame at the bottom of the battery and
connect to the charger for charging. When the battery is fully charged, the charger light
changes from red to green.
2. Power On/Off: Long press the power button to turn on/off the display power.
3. Display: After the display is turned on, briefly press the power button (<0.5s) to see the
different trip modes. The information displayed will be switched between the daily
kilometers (TRIP) - total kilometers (ODO) - Maximum speed (MAX) - Average speed
(AVG) - Remaining distance (RANGE) - Energy consumption (CALORIES) - Output power
(POWER) - Travel time (TIME).
4. Headlight: By pressing and holding the plus button, the controller will turn on/off the
headlight.
5. PAS Mode: You must turn on the battery to use the e-bike in pedal-assisted mode.
Power assist is triggered when you pedal forward, and stops when you stop pedaling,
sometime with a delay. If no power is needed, turn off the power of the battery.
6. Walk Assist Mode: Long press the “-” button until the walk assist symbol appears. Next
press and hold down the “-” button and the walk assist will activate. The electrical bike
runs at a constant speed of approx. 5 km/h. After releasing the “-” button, the motor stops
automatically and switches back to level 0.
Function introduction:
3

Product installation:
1. After removing the foam, place the bike as shown.
2. Loosen the screws of the handlebar stem, turn the stem to the correct
position and then tighten the screws.
4

3. Install the handlebars. Loosen the screws securing the handlebars, put the
handlebars on and tighten the screws. Tighten the handlebar stem screws
one last time to make sure the handlebars are in place.
4. Loosen the 3 screws circled in the picture, fix the front fender fixing hook and
the headlight bracket together with the screw on the front fork, and then use the
screw to fix the front fender support on the front fork, as shown in the picture.
5

5. Loosen the screws of the protective pad and remove the protective pad.
The protective pad can be discarded after removal.
7. Place the front wheel on the front fork for installation, pay attention to the
disc brake pad and the disc brake to match in place.
6. Turn the display down and turn the bike upside down as shown. Remove
the boot from the tire.
6

8. Loosen the nut on the front axle quick release to separate it from the screw.
9. Insert the front axle quick release screw into the front axle core, tighten it with the
nut, and then press the quick release handle to lock the front fork.
7

11. After installing the pedals, place the bike as shown, remove the saddle cover,
and adjust display to its original position.
12. Loosen the saddle switch, adjust the saddle to a suitable height and tighten
the switch.
10. Install the pedals. Note the markings on the pedal screws and on the crank
arms. Stamp with "L" is the left pedal, stamp with "R" is the right pedal, the right
pedal is installed on the side of the sprocket. NOTE: The left pedal is tightened to
the left and the right pedal is tightened to the right.
8

Product parameter
Dimensions
Performance Parameter
Electrical Specifications
Features
Item
Main material
Product size
Pedal-ground distance
Tire size
Package size
Product weight
Package weight
Battery weight
Maximum load
Maximum speed
Max range for assisted mode
Maximum climbing angle
Operating temperature
Waterproof level
Battery type
Battery capacity
Battery rated voltage
Motor rated voltage
Motor rated power
Charging voltage
Input voltage
Undervoltage protection value
Overcurrent protection value
Charging time
Display
Headlight
Braking method
Speed Transmission
Parameter
Aluminum alloy
194*113*69CM
12.8CM
700C*45C
157*25*87CM
26.2KG
34.6KG
3.35KG
150KG
25KM/H
100-120KM
20°
-20℃~55℃
IPV4
Lithium-ion battery
15Ah
36V
36V
250W
42V/3A
220V
30±1V
15A
5-6H
LCD
Yes
Mechanical disc brakes
SHIMANO 7S
Display user instructions
1. Introduction of display
Model: DP C11.CAN BUS
2. Specifications
• Operating temperature: -20℃~45℃
• Storage temperature: -20℃~50℃
• Waterproof: IP65
• Storage room Humidity: 30%-70% RH
9

3. Functional Overview
• Speed display (including top speed and average speed, switching between km and miles)
• Battery capacity indicator
• Lighting control
• Brightness setting for backlight
• Walk assistance
• Indication of performance support
• Motor output power indicator
• Time display for single journeys
• Kilometer stand (including single-trip distance, total distance and remaining distance)
• Setting the support levels
• Energy consumption indicator CALORIES (Note: If the display has this function)
• Display for the remaining distance (Depends on your riding style)
• Information view (battery, controller, HMI and sensor)
• Error codes view
4. Display
1. Display of battery capacity in real time.
2. Support level
3. The display shows this symbol , when the lights are turned on.
4. Unit of speed
5. Digital speed display
6. Trip: Daily kilometers (TRIP) - Total kilometers (ODO) - Top speed (MAX) - Average speed
(AVG) - Remaining distance (RANGE) - Energy Consumption (CALORIES) - Output power
(POWER)- Travel time (TIME).
Service: Please see the service section
10

There are three buttons on the operating unit of the display, i.e., the power button , plus
button and minus button .
6. Normal operation
6.1 Switching the System ON/OFF
Press and hold the power button (>2S) on the display to turn on the system. Press and
hold the power button(>2S) again to turn off the system.
If the "automatic shutdown time" is set to 5 minutes (it can be reset with the "Auto Off"
function, see "Auto Off"), the display will automatically be turned off within the desired time
when it is not in operation. If the password function is enabled, you must enter the correct
password to use the system.
6.2 Selection of Support Levels
When the display is turned on, press the “+”or “-” button (<0.5S) to switch to the support
level, the lowest level is 0, the highest level is 5. When the system is switched on, the
support level starts in level 1. There is no support at level 0.
For different assist levels please see part "Assist Mode".
5. Key definition
11

6.3 Mode selection
Briefly press the power button (<0.5s) to see the different trip modes.
Trip: daily kilometers (TRIP) - total kilometers (ODO) - Maximum speed (MAX) - Average
speed (AVG) - Remaining distance (RANGE) - Energy consumption (CALORIES) - Output
power (POWER) - Travel time (TIME).
6.4 Headlight / backlight
Hold the “+” button (>2S) to activate the headlight and backlight.
Hold the “+” button (>2S) again to turn off the headlight. The brightness of the backlight
can be set in the display settings "Brightness".
6.5 Walk Assistance
The walk assistance can only be activated with a standing e-bike.
Activation: Press the “-” button until this symbol appears. Next press and hold down
the “-” button whilst the symbol is displayed, now the Walk assistance will activate. The
symbol will blink and the e-bike moves approx. 5 km/h. After releasing the “-” button,
the motor stops automatically and switches back to level 0.
12

6.6 SERVICE
The display shows "SERVICE" as soon as a certain number of kilometers or battery
charges has been reached. With a mileage of more than 5000 km (or 100 charge cycles),
the “SERVICE" function is displayed on the display. Every 5000 km the display
"SERVICE" is displayed every time. This function can be set in the display settings.
6.7 Battery capacity indicator
The battery capacity is shown in the top left of the display. Each full bar represents a
remaining capacity of the battery in a percentage.
(as shown in the table below):
Capacity Range Indicator
80%-100%
60%-80%
40%-60%
20%-40%
5%-20%
<5%
13

7. Settings
After the display is turned on, press and hold the “+” and “-” buttons (at the same time) to
enter into the setting menu, by pressing the “+” or “-” button (<0.5S), you can select
Display Setting, Information or Exit. Then press the power button (<0.5S) to confirm your
selected option. Or highlight "EXIT" and press the power button (<0.5S) to return to the
main menu, or highlight "BACK" and press the power button (<0.5S) to return to the
Settings interface.
7.1 Display Setting
Press the "+" or "-" button (<0.5S) and highlight Display Setting, and then briefly press the
power button (<0.5S) to access the following selections.
7.1.1 "TRIP Reset" Reset mileage
Press the "+" or "-" button (<0.5S) to highlight “Trip Reset” in the Display setting menu,
and then press power button (<0.5S) to select. Then with the "+" or "-" button choose
between “YES” or “NO”. Once you have chosen your desired selection, press the power
button (<0.5S) to save and exit to the "Display setting".
14

7.1.2 "Unit" Selections in km/Miles
Press the "+" or "-" button (<0.5S) to highlight “Unit” in the Display setting menu, and then
press power button (<0.5S) to select. Then with the "+" or "-" button choose between
“Metric” (kilometer) or “Imperial” (Miles). Once you have chosen your desired selection,
press the power button (<0.5S) to save and exit to the "Display setting".
7.1.3 "Brightness" Display brightness
Press the "+" or "-" button (<0.5S) to highlight “Brightness” in the Display setting menu,
and then press power button (<0.5S) to select. Then with the "+" or "-" button choose
between "100%" / "75%" / "50%" /" 30%"/"10%". Once you have chosen your desired
selection, press the power button (<0.5S) to save and exit to the "Display setting".
15

7.1.4 "Auto Off" Set Automatic system switch off time
Press the "+" or "-" button (<0.5S) to highlight “Auto Off” in the Display setting menu, and
then press power button (<0.5S) to select. Then with the "+" or "-" button choose between
“OFF”, "9"/"8"/"7"/"6"/ "5"/ "4"/"3"/"2"/"1", (The numbers are measured in minutes). Once
you have chosen your desired selection, press the power button (<0.5S) to save and exit
to the "Display setting".
7.1.5 "Assist Mode" Set support level
Press the "+" or "-" button (<0.5S) to highlight “Max Pass” in the Display setting menu, and
then press power button (<0.5S) to select. Then with the "+" or "-" button choose between
“3/5/9” (the amount of support levels). Once you have chosen your desired selection,
press the power button (<0.5S) to save and exit to the "Display setting".
7.1.6 "Service" Switching the notification on and off
Press the "+" or "-" button (<0.5S) to highlight “Service” in the Display setting menu, and
then press power button (<0.5S) to select. Then with the "+" or "-" button choose between
“NO” or “YES”. Once you have chosen your desired selection, press the power button
(<0.5S) to save and exit to the "Display setting".
16

7.2 “Information”
Once the display is turned on, press and hold the "+" and "-" buttons (at the same time) to
enter into the setting menu, press the “+”or “-” button (<0.5S) to select “Information”, then
press the power button (<0.5S) to confirm and enter into "Information".
7.2.1 Wheel Size
Press the “+” or “-” button (<0.5S) to highlight “Wheel Size”, then press the power button
(<0.5S) to confirm and view the wheel size. To return, press the power button (<0.5S) to
exit back to the "Informa¬tion".
This information cannot be changed, this is only for information about the e-bike.
7.2.2 Speed Limit
Press the “+” or “-” button (<0.5S) to highlight “Speed Limit”, then press the power button
(<0.5S) to confirm and view the speed limit. To return, press the power button (<0.5S) to
exit back to the "Infor¬mation".
This information cannot be changed, this is only for information about the e-bike.
17