FANATEC McLaren GT3 User manual

www.fanatec.com
QuickGuide
EN
Fanatec®is a registered trademark of Endor AG
Designed and developed by Endor AG in Germany
Manufactured by
Seligenthaler Straße 16 a - 84034 Landshut - Germany
Telephone: [phone] Fax: [phone]
Email: [email protected]
Internet: www.fanatec.com - www.endor.ag
TUNING MENU
To enter the tuning menu press the [TUNING MENU] button.
To navigate inside the menu, use the D-PAD [FunkySwitchTM]:
• Press the [FunkySwitchTM] up or down to access 5 setups
(SET 1, SET 2, … 5)
• Press the [FunkySwitchTM] right or left to go through the
options
• Rotate the [FunkySwitchTM] left or right to change option
values. The new values are in e󰀨ect immediately and will
be stored inside the wheel base.
SHIFTER CALIBRATION
To enter shifter calibration mode, simultaneously press and
hold the [TUNING MENU] + buttons, as highlighted below.
For the detailed process read the shifter manual.
CENTER CALIBRATION
If a center calibration is needed (e. g. after rmware
update of wheel base) you need to enter the tuning menu
by pressing the [TUNING MENU] Button. “SETTING” will
appear on the OLED display. Now turn the wheel to its
center position and then press the [FunkySwitchTM] +
buttons at the same time to calibrate the wheel center.
To switch between modes simultaneously press and hold
the buttons + , highlighted below, for one second.
The wheel base LED indicates the active mode:
- Green means Xbox One mode
- Red means PC mode
- Blue means PS4TM mode*
- Purple means compatibility mode*
TUNING MENU
TUNING MENU
FunkySwitchTM
* not applicable for every Fanatec wheel
base, please check the individual user
manual of your Fanatec wheel base.
MODES
SETTING
TUNING MENU
FunkySwitchTM

ANALOG PADDLE MODES
The CSL Elite Steering Wheel McLaren GT3 has two analog
paddles. With the blue multi-position switch you can
change between modes:
A Clutch bite point**
Left & right paddle work in parallel. The paddle that is
pressed further is valid.
B Handbrake + Clutch
Left: handbrake; right: clutch
C Brake + Throttle
Left: brake; right: throttle
D Mappable analog axes
paddles can be mapped as two additional axes
• Press both paddles all the way in. The display will show 100%.
• Release one paddle while keeping the other fully pressed.
The display now shows the percentage value of the released paddle while the
car’s clutch is still fully pressed.
• Set the released paddle to the percentage value where your car’s clutch starts to
bite (evaluate in earlier tests).
• As soon as the virtual start lights turn to green, completely release the fully
pressed paddle and the clutch is immediately at the bite point, held by the other
paddle.
** Clutch bite point feature (for race start)
In mode A this feature is activated anytime when both paddles are pressed to at least
5%.
ATTACHING THE RIM
Please download and install the latest PC driver and
wheel base rmware before mounting the CSL Elite
Steering Wheel McLaren GT3. You can obtain it at
Fanatec’s website (www.fanatec.com) in the download
section.
As an option for quick attaching and removal
of the wheel you may upgrade to the ClubSport
QuickRelease Adapter (CS QRA), available as an
accessory at www.fanatec.com.
Align wheel base axis to correct
position.
Slide CSL Elite Steering Wheel
McLaren GT3 onto wheel base axis
Use xing screw
(ISO 4762 M6 x 16mm) and hex key
from the backside of the wheel:
Only use the provided xing screw.
Push steering wheel
until the screw hole
matches with hole on
wheel base axis.
Turn the steering wheel top side down to see the bottom
side of the clamp ring to follow next step below.
1
2
3
4
Loosen and remove the xing screw to x
the clamp ring mechanism.
Use only the hex key from the wheel
compartment.
Proceed in reverse order to remove the
wheel from the base.
5BUTTON MAPPING
No. Button Button no. PC Xbox One
1 LSB (orange) 12 LSB
2 N (high bezel) 9 VIEW
3 Y (grey) 4 Y
4 X (red) 1 X
5FunkySwitchTM up, down, left,
right, press
Up, down, left, right, press
(26) up, down, left, right, press
6 RSB (orange) 11 RSB
7 P (high bezel) 10 Menu
8 B (grey) 3 B
9 A (red) 2 A
10 25 Guide
11 Toggle switch R –up/ down 7 / 31 LT (throttle) / RT (brake)
12 Tuning menu -/- -/-
13 Toggle switch L – up/ down 8 / 32 LT (throttle) / RT (brake)
14 Paddle mode switch (blue) See analog paddles modes described in this Quick Guide
15 Shifter paddle L (down) 6 LB
16 Shifter paddle R (up) 5 RB
17 Analog Paddle L
See analog paddles modes described in this Quick Guide
18 Analog Paddle R
5 10
17 18
4 9
3 8
15 16
2 7
1 6
12
14
13 11
IMPORTANT: Tighten only by using the short lever of
hex key!
IMPORTANT: Never use without screw!