F&F Filipowski sp. j.
Konstantynowska 79/81 95-200 Pabianice
phone/fax: (+48 42) 215 23 83 / 227 09 71 POLAND
http://www.fif.com.pl e-mail: fif@fif.com.pl
ELECTRONIC BI-STABLE
PULSE RELAY
Do not dispose of this device to a garbage bin with other unsorted waste!
In accordance with the Waste Electrical and Electronic Equipment Act
any household electro-waste can be turned in free of charge and in any
quantity to a collection point established for this purpose, as well as to the
store in the event of purchasing new equipment (as per the old for new rule,
regardless of brand). Electro-waste thrown in the garbage bin or abandoned
in the bosom of nature pose a threat to the environment and human health.
BIS-411i
230V
WARRANTY. The F&F products are
covered by a warranty of the 24 months
from the date of purchase. Effective only
with proof of purchase. Contact your
dealeror directly with us. More
information how to make a compliant can
be found on the website:
www.fif.com.pl/reklamacje
- 1 -
Electronic bi-stable pulse relays BIS-411 230V enables the user to
actuate lighting or other devices from various locations by means
of control buttons in parallel connection.
PURPOSE
L N
N
N/L
BIS
power supply 230V AC
contact / current load AC-1 separated 1 C/O / 16A
control pulse 110÷265V AC <20mA
max current control buttons
activation delay 0.1÷0.2sec
signalling of supply green LED
signalling of activation red LED
working temperature -25÷50°C
connection screw terminals
tightening torque 0.4 Nm
dimensions 1 module (18mm)
Σ5mA
power consumption
standby 0,15W
on 0,6W
2
2,5mm
fixing on the TH-35 rail
ingress protection IP20
TECHNICAL DATA
WIRING DIAGRAM
11 12
13
6
L
N
11 12
13
6
L
N
control impulse: N control impulse: L
SUPPLY
1-3 power relay: 100-265V AC
CONTROL INPUTS
6 control inputs
CONTACT
11 power input contact COM
10 output: NC contact (passive)
12 output: NO contact (active) D150203/150520
L
N
1
4
7
10
2
5
8
11
3
6
9
12
U
BIS-411
Example of relay connection with N control pulse
Table of power
2000W 1000W
1250W
incandescent fluorescent
halogen
The above data are indicative and will heavily depend on the
design of a specific receiver (that is especially important for LED
bulbs, energy-saving lamps, electronic transformers and pulse
power supply units), switching frequency and operating
conditions.
For more information visit www.fif.com.pl
energy-saving LED
500W 250W
- 2 -
FUNCTIONING
The receiver is actuated by means of a current pulse triggered by
pushing any bell push connected to the relay. The receiver is
deactivated by another pulse or after a preset time. The relay does
not “memorize” the position of the relay contact, i.e. in case of
supply voltage decay and the subsequent return of supply voltage,
the relay contact will be set in the off position. Such a solution
prevents the automatic actuation of the receivers controlled that
might occur without proper supervision after a long-lasting decay
of supply voltage.
ATTENTION!
The BIS-411 230V is compatible with bell
pushes equipped with fluorescent lamps
(ΣI<5mA).
ASSEMBLY
1. Turn OFF the power.
2. Put on the relay on the rail in the switchgear box.
3. Connect the power cable to contacts 1-3 with accordance
choosen control option the relay (control impulse L or N).
4. The timers switching which are connect in parallel connect to
contact 6 and to cable which is connect to contact 3.
5. The activated receiver connect in series to contacts 11-12.
6. By screwdriver set to switching OFF delay.
- 4 -
Relay version "i" is to pin adapted to cooperate with the receivers
with high starting current, such as LED fluorescent lamps,
ESL fluorescent lamps, electronic transformers, discharge
lamps, etc.
