Fanimation FP8014**-220 User manual

OWNER’SMANUAL
READ AND SAVETHESE INSTRUCTIONS
Model No. FP8014**-220
The Arden™
Oscillating Floor Fan
Net Weight 6kg. (13.10lbs)

Table of Contents
Unpacking Instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Electrical and Structural Requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
How to Assemble Your Floor Fan. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Parts List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
1. Read your owner’s manual and safety information before installing your new fan. Review the accompanying assembly diagrams.
2. Before servicing or cleaning unit, unplug unit from power outlet.
3. Be careful of the fan and blades when cleaning, painting, or working near the fan. Always unplug the fan before servicing.
4. Do not insert anything into the fan blades while the fan is operating.
5. This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of
6. Children should be supervised to ensure that they do not play with the appliance.
7. Ensure that the fan is switched off from the supply mains before removing the guard.
8. If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to
avoid a hazard.
experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person
responsible for their safety.
Additional Safety Instructions
Important Safety Instructions
WARNING: To avoid fire, shock and serious personal injury, follow these instructions.
1. To avoid possible shock, do not operate fan without blades.
2. The fan must be connected to a grounded electrical supply as a precaution against possible electrical shock.
3. Follow the recommended instructions for the proper method of operating your fan.
WARNING: This product is designed to use only those parts supplied with this product and/or accessories designated specifically for
use with this product. Using parts and/or accessories not designated for use with this product will void your warranty and could result in
personal injury or property damage.
WARNING: Do not insert foreign objects in between rotating fan blades.
WARNING: For indoor use only.

3
This Manual is Designed to Make it as Easy as Possible for You
To Install, Operate, and Maintain Your Fan
Check to see that you have received the following parts:
Motor Assembly
• Motor assembly
• Timber tripod legs
Timber Tripod Legs
• Hardware Bag
▲ WARNING
Do not install or use fan if any part is damaged or
missing. This product is designed to use only those
parts supplied with this product and/or any accessories
designated specifically for use with this product by
Fanimation. Substitution of parts or accessories not
designated for use with this product by Fanimation could
result in personal injury or property damage. Contact
your retail store for missing or damaged parts.
Hardware bag
Unpacking Instructions
NOTE: The illustration shown is not to scale. Actual configuration or finishes may vary.
Electrical and Structural Requirements
▲ WARNING
To avoid fire or shock, follow all wiring instructions
carefully. Any electrical work not described in these
instructions should be done by a licensed electrician.
ELECTRICAL REQUIREMENTS
This fan requires a grounded electrical supply
line of 220 volts AC, 50 Hz, 10 amp circuit. 2.4m power
cord included. NOT for Damp Location Use.
▲ WARNING
To Avoid Fire Or Electrical Shock, Do NOT Use This Fan
With Any Solid-State Speed Control Device And Do NOT
Use By Open Window.

4
How to Assemble Your Floor Fan
x 12
3/16-24 x 22 mm
CAP HEAD WITH
SPRING WASHER
HARDWARE USED:
Motor Assembly
Leg
T-Wrench
1. Attach the timber tripod legs to the motor
assembly using 3/16-24 x 22 mm screws. Use the
supplied T-wrench to tighten the screws to ensure
the legs are securely attached to the motor assembly.
Ensure legs are positioned with the sticker side facing
inwards towards the mounting brackets. Do not
over-tighten the screws. (Figure 1)
4. Select the desired airflow, located on back of motor
assembly by rotating switch clockwise. (Figure 4)
3. You have now completed the assemby of your
fan. Plug cord directly into the wall socket and
turn on the power supply. (Figure 3)
Figure 3
Rubber Cap
2. Assemble the rubber caps on to the screws of
each leg. (Figure 2)
Figure 2
Rotating Switch
Figure 4
Figure 1
0 = OFF
1 = HIGH
2 = MEDIUM
3 = LOW

5
Maintenance
Periodic cleaning of your fan is the only maintenance that
is needed.
When cleaning, use only a soft brush or lint free cloth to
avoid scratching the finish.
Abrasive and/or non-abrasive cleaning agents are not
required and should be avoided to prevent damage to
finish.
CAUTION
Do not use water when cleaning your fan. It could
damage the motor or the finish and create the possibility
of electrical shock.
3
Exploded-View
FP8014**-220 Parts List
Model #FP8014**-220
Ref. # Description Part #
1 Motor Assembly AMA8014**-220
2 Timber Tripod Legs
3/16-24x22 mm Screw
Rubber Cap
T-Wrench
AP801420**
3
Hardware Bags Containing:
HDWFP8014**
2
1
How To Order Parts
When ordering repair parts, always
give the following information.
For repair parts:
Phone [phone]
www.myfan.com au
• Part Number
• Part Description
• Fan Model Number
NOTE: The illustration shown is not to scale.
Actual configuration or finishes may vary.

Copyright 2012 Fanimation 2012/03 V.01
Distributed in Australia by MyFan Pty Ltd
www.myfan.com.au