Fantask EP23484WH User manual

STAND FAN
OPERATING INSTRUCTIONS
MADE IN CHINA

IMPORTANT SAFEGUARDS
When using an electrical appliance, basic safety precautions should always be observed,
including the following:
READ ALL INSTRUCTIONS BEFORE USING
WARNING: To reduce the risk of fire, electrical shock, or injury to
person:
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance by a person responsible for
their safety.
1. The product is for household use only.
2. Connect the appliance to single-phase AC supply of the voltage specified on the rating
plate.
3. Never leave the fan unattended while it is in use. Always turn the product to the OFF
position and unplug it from the electrical outlet when not in use.
4. Extreme caution is necessary when any fan is used by or near children, invalids or elderly
person and whenever the fan is left operating and unattended.
5. Do not run cord under carpeting and do not cover cord with throw rugs, runners or the
like. Do not route cord under furniture or appliances. Arrange cord away from traffic area
and where it will not be tripped over.
6. Do not operate the fan with a damaged cord or plug, or after the fan malfunctions, has
been dropped, or damaged in any manner.
7. If the supply cord is damaged, it must be replaced by the manufacturer or its service
agent or a similarly qualified person to avoid a hazard.
8. Use the fan in a well-ventilated area. While using, distance of no less than 20cm should
be kept away from wall or corner to ensure the air intakes or exhaust openings should not
be blocked unexpectedly. The fan must not be located immediately below or besides a
curtain or the likes.
9. Do not insert or allow fingers or any other objects into grill to avoid a mechanical danger
when in use. Do not block air intakes or exhaust openings in any manner.
10. Use the fan on flat, dry floor only.
11.Ensure that the fan is switched off from the supply mains before removing the guard.
12.This product employs overload protection (fuse). A blown fuse indicates an overload or
short-circuit situation. If the fuse blows, unplug the product from the outlet. Replace the
fuse as per the user servicing instructions (follow product marking for proper fuse rating)
and check the product. If the replacement fuse blows, a short-circuit may be present and
the product should be discarded or returned to an authorized service facility for
examination and/or repair.

13.This appliance has a polarized plug (one blade is wider than the other). To reduce the
risk of electric shock, this plug is intended to fit in a polarized outlet only one way. If the
plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified
electrician. Do not attempt to defeat this safety feature.
14.When replacement of Plug, the safety Device（Fuse）is to be reinstalled or remounted
as previously installed.
FOR HOUSEHOLD USE ONLY
SAVE THESE INSTRUCTIONS
SPECIFICATIONS
MODEL NO
RATED VOLTAGE
RATED POWER
EP23484WH
120V~60Hz
65W
STRUCTURE AND PARTS

ASSEMBLE INSTRUCTIONS
The fan is packaged with its foundation and/or other parts unattached. You must attach
them before operating the fan.
WARNING: Never operate without its foundation and/or other parts attached. Do operate
the fan only in upright position; any other position could create a hazardous situation.
Assemble sequence of the foundation and other parts as follow:
a. Unpack the fan and remove all the parts from the package.
b. Use the bend bolt and the press plate provided to attach the stand post assemblies to
the base.
c. Adjust the lift pole to a desired length, and then lock it with the locknut for lifting.
d. Loose the locknut for switch case and insert the lift pole into the hole located on the
bottom of the switch case in place, then fasten the locknut back tightly.

e. Take off the motor shaft cover from the
fan head, and revolve the triangle screw off, then let three columns into the three holes in
place fully, and finally tighten the triangle screw counterclockwise.
f. let the notch on the back of the big fan blade stuck in the stopper pin of the motor shaft,
and then tighten the small fan blade counterclockwise.
g. To attach the front grill to the back grill, you should use the grill ring carefully to hold
them together and fasten the grill ring with the screw provided.
INSTRUCTIONS FOR USE
Before using the fan make sure that it is on a flat and stable surface.
Damage may occur if it is placed on an incline or decline.
Set all the switches to OFF position, then insert the plug directly into a standard AC
socket-outlet. Be sure plug fits tightly into outlet.

a. Press the button on to start the fan and select the fan speed level, as per the following
sequence: 1 2 3 1
The fan speed selecting can be circulated and the speed pilot lamp will be on during the fan
operating.
b. Press the button Mode to choose your desired wind mode as per the following sequence:
normal wind nature wind sleeping wind normal wind
The wind mode selecting can be circulated and the wind mode pilot lamp will be on during
the fan operating.
c. Set the time by pressing the timer button to select a desired timing level, the range is
between 1-15 hours. The pilot light corresponding to the selected timing level will be
illuminated.
d. Press the shaking head knob to select whether you need to let it shake head, as per the
following sequence: shaking not shaking shaking
Press the button OFF To turn off the fan, and all the pilot lights will be go out.
Note: all above functions can be operated under the remote control.
User Servicing Instructions：
——how to physically replace the fuse：
WARNING：If the FUSE is broken, do not try to replace it yourself, it must be
replaced by the manufacturer or its service agent to avoid a hazard, or find your
dealer direct to replace a new product.
a) Grasp plug and remove from the receptacle or other outlet device. Do not unplug by
pulling on cord.
b) Open fuse cover, slide open fuse access cover on top of attachment plug towards blades,
or push on tabs located next to the blades.
c) Remove fuse carefully, such as whether to push the fuse from the other side or turn fuse

holder over to remove fuse.
d) Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse.
e) Close fuse cover, Slide closed the fuse access cover on top of attachment plug or push
cover closed so that all tabs latch.
f) Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should
not be removed. Discard product if the attachment plug is damaged.
MAINTENANCE
1. Always remove the plug from the socket-outlet and allow the fan to stop acting before
clean the fan.
2. Clean the external surfaces of the fan with a soft damp (not dripping wet) cloth.
WARNING:
Do not immerse the fan in water.
Do not use any cleaning chemicals such as detergents and abrasives.
Do not allow the interior (special for the PCB) to get wet as this could create a
hazard.
3. When the unit is not in use, make sure that it is unplugged from the wall socket. To store
the fan, you may pack it in the original carton and store it in a cool and dry place until later
use.
4. In case of malfunction or doubt, do not try to repair the fan yourself, it may result in a fire
hazard or electric shock.