Farenheit Mobile Video System User manual

OWNER'S MANUAL
Mobile Video System
~
I "
3.3" WIDE TOUCH SCREEN "ONITO~
I!
I
_ .=:: 'I---:S~ I -----------------------.---~----
Ii It~ ~AIVIN ~.. I;i;J .. ~c 0- O.E'ET

Table of Contents 1
Safety Information :2
Features 4
Accessories '" 5
Wire Connection 6
Unit Installation and Removal '" 9
Front Panel. 16
Remote Control 20
Touch Screen Operations 25
Touch Screen Calibration
'" 25
Main Menu 26
Radio Operations 27
DVD Operations 28
Bluetooth Operations 34
IPOD Operations ;40
SD CARD Operations .42
USB Operations 42
DIM 42
AV IN 1Operations '" '" 43
AV
IN 2Operations 43
DIGITAL TV Operations 44
TV Operations 45
NAVI Operations 46
System Parameters Setup 50
Specifications :53
Troubleshooting 54
Disc Notes 56
- 1-

PLEASE READ COMPLETELY AND BECOME FAMILIAR WITH THE CONTENTS
OF THIS MANUAL BEFORE INSTALLATlON AND OPERATION OF THIS UNIT,
AND KEEP IT CAREFULLYFOR FUTURE REFERENCE.
This unit is aclass 1laser product. The laser beam may cause hazardous
radiation
if exposure to laser system directly. Do not attempt to disassemble
the unit personally.
This unit has been designed and manufactured to assure personal safety. Improper
use can result in electric shock or fire hazard. The safeguards incorporated in this
unit protect you
if you observe the following procedures for installation, use and
servicing. This unit doesn't contain any parts that can be repaired by the user.
If the
unit requires maintenance, contact an authorized service center.
A Warnings
-Do not expose the product to rain, water or excessive moisture. This could cause
electrical shorts, fire or other damage.
-This product is designed to operate with a12 volt DC, negative ground battery
system. Use the proper power supply.
-The monitor is operated automatically. Do not push in or pull out the monitor
or try to
reverse the monitor manually! Do not attempt to adjust the monitor angle upward or
downward manually. Itwill cause damage to the Monitor Mechanism Structure.
-Do not impact the monitor with ahard object. It may cause permanent damage.
-Do ground all equipments and works in order to avoid causing damage to the unit
by electrostatic discharges.
-The userwho handles this product takes all necessary precautions to avoid ESD
(Electro-Static Discharge) failures.
-Do not attempt to install
or service your unit by yourself. Installation or servicing of
the unit by persons without training and experience in electronic equipment and
automotive accessories may be dangerous and could expose you to the risk
of
electric shock or other hazards.
-2-

Cautions:
CD To reduce the risk of fire or electric shock, and annoying interference, use only the
recommended accessories.
(I) \Nhile driving, keep the volume level low enough to be aware of road and traffic
conditions.
CD Parking in direct sunlight can produce very high temperatures inside your vehicle.
Give the interior achance to cool
down before starting playback.
CD Do not use any chemical solvent, cleaning agent or corrosive detergent to clean
away dirt on the surface
of the TFT monitor screen. It may cause irreversible damage.
CD Small black and shiny dots inside the liquid crystal panel are normal for liquid
crystal product.
Q) In extremely cold temperatures, the movement of the picture may be slow and the
picture
may be dark, but this is not amalfunction. The unit will work normally once
reach its operating temperature.
CD Do not use and store the unit in dusty, high temperature and high humidity
environments.
CD Do not use the unit immediately when you bring it from cold to warm place. Fast
growing temperature, may cause moisture condensing which influence the unit for
certain time.
NOTE:
This user's manualis only for reference.
Modifying rights are reserved.
Specifications are subject to change without notice.
-3-

Single DIN AN Source Unit with 8.3" Digital Flip-up TFT-LCD Touch Screen &
Bluetooth 2.0
•World's First 8.3" Flip-up Source Unit
•Nearly 40% More Viewing Area Than 7"
• 3 Selectable User Interface
•Theft Deterrent Front Panel Cover Included
•Extended Sleeve &Trim Ring for Covered Dash Installation Included
•Tri-Motorized Monitor Telescopes Forwards/Backwards with Angle Memory
•TFT-LCD Monitor Backlight by Ultra-Bright LEOs
•Accepts Add-On GPS Navigation Module,NAVIBOX-1 (Optional)
•Accepts Add-On Digital
TV Tuner ModUle, DTV-1 &DTV-MH
•Playback from DVDR/RW&CDR/RW, Including VCD, MP3, MP4 &DivX
•IPOD Input Control (requires IPOD cable)
•Mini-USB Connection for MP3 &MP4 Playback from 16GB Flash Drive
•16GB SO Card Reader on Faceplate for MP3, MP4, DivX &Xvid Playback
•30MB Internal Memory for Background &Screen Saver Images
•18
FM /12 AM Station Memory
• SOw x 4 MOSFET Powered Speaker Level Outputs
•
2V Front &Rear Pre-Amp Outputs
•
2V Variable Subwoofer Pre-Amp Output with LPF (80, 120, 160Hz)
• AN Outputs for Multiple Components
• AN Inputs for Secondary Source
•3.5mm
AN Input at Faceplate
•Reverse Camera Input with Trigger
•Custom &Pre-Set EO Settings
•Audio Staging Controls
•12/24 Hour Clock
•USA/European Frequency Stepping
•NTSC/PAL Auto Selection
•
High Definition Digital Panel with LED Back Light
•400 NIT LED Backlight Brightness
•Steering
VVheel Control
•
Built-in Analog TV Tuer(optional)
Bluetooth Features (Optional)
•Work with
Most Bluetooth V2.0 Enabled Phones
•Noise &Echo Cancellation
•Contacts List Transferred for Easy Access Dialing
•Caller 10 Shows Name and Numberfrom Contacts List
•Recent Calls &Talk Time Logs
•A2DP for Streaming MP3 Playback
-4-

ACCESSORIES
1234
~
@"
Bolt and Nut M5 x 1 Back Strap x 1 Nut M5 x 1
M5X5 Screws x 4
5678
~
(0 ]D
~
M4X3 Screws x 4 Remote Control x 1 Operational Manual x 1
Keys x2
910 11
12
-
~
~
0
Mounting Sleeve x 1 Power Wire x 1 Connecter Wire x 1
Trim Bezel x 1
(BLACK)
(WHITE)
13
14 15
16
I I
L: C)[£JI
flti!f!#t
~
Trim Bezel x 1 Mounting Sleeve x 1 .
Theft deterrent front panel x 1 IPod Cable x 1
(Optional)
17 18
cQ~
19
~
20
m:§
USB Cable x 1 AV IN Cable x 1
21
~
Amplifier Power Wire x 1 Power Amplifier Cable x 1
(WHITE)
22
0
:12 -='
I: __ .
;,
!j
. 0 a
External Microphone x 1 Digital Power Amplifier
(Optional) Box x 1
- 5-

Cautions:
-To prevent short circuits, remove the key from the ignition and disconnect the
terminal ofthe battery.
-Make the proper input and output cable connections for each unit.
-Connect the wiring harness cables in the following order: ground wire, battery wire,
ignition wire.
-Reconnect the terminal
of the battery.
-Do not connect the yellow wire of this product directly to the battery terminal.
-Do remember to connect the red wire
of this product to the ACC. of the ignition key
switch. Failure to do may result in draining offthe battery charge prematurely.
-Ifthe fuse blows, first make sure that the cables have not caused ashort circuit,
then replace the old fuse with new one with the same rating.
-Do not let unconnected cables or terminals touch the metal on the car or other
conductor.
-To prevent short circuits, do not remove the caps form unused terminals or from the
ends
of the unconnected cables.
-After the monitor unit is installed, check whether the brake lamps, blinkers, wiper,
etc. on the vehicle are working properly. Ifnot, please make sure they are proper
installed.
-Insulate unconnected wires with vinyl tape or other similar material.
AWarnings:
Disconnecting the Battery
To prevent ashort circuit, be sure to turn offthe ignition and remove the negative (-)
battery cable prior to installation.
Reconnecting the Battery
When wiring is complete, reconnect the battery negative terminal.
Fuse Replacement
Never replace any fuse with one of ahigher value than the fuse supplied with your
unit. Using ahigher current rated fuse may cause damage to your unit and/or
electrical wiring.
~ ~ ~ e::::::J ~ ~
@K}
~
...
~ ~ ~ ~
~
~ c:::=> c:::=> c:::=>
c:::=> c:::=>
c==J
qz:=]}
c=D
c::::.;;)
c::zt)
1. 28PIN SOCKET
2. AUDIONIDEO OUTPUT &INPUT
3. IPOD ADAPTER, RADIO &ANALOGUE TVANTENNA
- 6-

...... 1IIIIC:::t::::l===''':::··A:::C¥:::. =±*=~};'dlll NAVIBOX-!N ADAPTER(OPTJONAl)
DIGITAL TV ADAPTER(OPTJONAl)
======= ...... =--=~=.=-= .... """- SR·1 (OPTIONAL)
====~~'=====' ILL (OPTIONAl)
~~~~~~~~~~= SR .. GND(OPTlONAU
, AMP REM
AUTO ANT
BRAKE
GND
i);:=::t::6?dl!f== Ace
~===O::::R£!::AN!:::!:!GE::::===::::::::=t::;:f=:x::l REVERSE CONTROL
,. ,,~:::::1~~====trmmu]~D (Active High Input)
~ MIC IN
..::::r:E~p~~:ljj AUX LIN
,AUX RIN
~:r:~~~~~=:H3 RV VIDEO
?VIDEO IN
I"'t!::::t---i ~~~c::::::I:~TITI5Wf==e==8III::::D VIDEO OUT
1~0~~~ ~=r=:r=e~~9:F4111(I=n SUB OUT
I
k~~Y,:i/H:!T:E:3Ei§~LF OUT
RED RF OUT
WHITE LR OUT
RED RR OUT
~., .. ~.::'.:L .... _. ~'POD
\WI-t _ ~~. ~~~~~-~I~:~~~Onal)
Brake Control
Connect the brake control wire AUTO_ANT (see Wiring Diagram). It is necessary to
connect the Brake Control wire to the Hand-brake switch of the car. While driving, the
TFT monitor will display the alarm picture (see as follows) in order to ensure the
safety.
AWARNING
VIDEO VIEWING IS NOT
AVAILABLE
WHILE DRIVING
Under the Rear View Mode, the Brake Control function is no effective.
Auto Antenna Control
Connect the auto antenna control wire AUTO_ANT (see Wiring Diagram). The
antenna will lift when the unit startup; it will descend when the unit turnoff.
-7-

~
~.
:::s
CQ
C
I»
CQ
Dl
3
BLUE
OPTIOIW. lPOO CAlllE
AUTO ANTEN
~ iql
D
,0
~ _.rn""",,cID r ~
- ClPT1ONAl. \""l:£!'
~ B.t.C/(UP
-~-~"" CAMERA
.~
1
-_._-----_ ...... _---'" ~
Ground
RED
BLACK
GROUND
ACC
BATTERY + YELLOW
........ --- -_._- .... ' .. _--_ ..... _ .......
., e.R~KE., ~J.N.K
__ 1
0
··········· . ···········'l····'·" .. :::~~:···- -r'l
rrfl U'.. .. . ;:;~::::·~:'.~.:, ,., " .. , _~~}j.,,:::::::1.":::.
, "., .. _ .. "., " .. _.,., .. "." _ .-& ~ ., .
IDIGITAL ~~~~R A~P~;FIER
~l
.-,
~I ~I
co

Please read all of the instructions before beginning the installation. Recommend
having
your unit installed by aprofessional installation shop.
Tools and Supplies:
You will need these tools and supplies to install your unit:
-Torx type, flat-head and Philips screwdrivers
-Wire cutters and strippers
-Tools to remove existing radio (screwdriver, socket wrench set
or other tools)
-Electrical tape
-Crimping tool
-Volt meter/test light
-Crimp connections
-
16 gauge wire for power connections
- 8 gauge speaker wire
Awamings:
Choose the mounting location where the unit will not interfere with the safe driving
conditions.
Install the unitwhere it does not
get in the driver's way and can not injure the
passenger ifthere is asudden stop, like an emergency stop.
Avoid installing the unitwhere it would be subject to high temperature, such as from
direct sunlight, or from hot air, from the heater,
or where itwould be subject to dust,
dirt
or excessive vibration.
Cautions:
Before finally installing the unit, connect the wiring temporarily and make sure it is all
connected up properly, the unit and the system
work properly.
Use only the parts included with the unit to ensure proper installation. The use
of
unauthorized parts can cause malfunctions.
Consult with your nearest dealer
if installation requires the drilling of holes or other
modifications
of the vehicle.
If installation angle exceeds 30 degrees from horizontal, the unit might not give its
optimum performance.
If the TFT monitor declines due to shock and vibration from outside, you
could correct the decline by closing the TFT monitor or restarting the unit.
-9-