Feider Machines FPB900W User manual

1
ORIGINAL INSTRUCTIONS
BELT SANDER
FPB900W
USER GUIDE
WARNING: READ THESE INSTRUCTIONS BEFORE USE THIS MACHINE.

2
CONTENTS
1. SAFETY WARNINGS…………..…………………………………………..………3
2. EXPLANATION OF SYMBOLS…….………………………………………………………….……7
3. PART LIST…………………………………………………………………………………………….…..8
4. TECHNICAL SPECIFICATION……….……………………………………..….……………..……9
5. ASSEMBLY AND USE………………….……………………………………………………………10
6. SERVICE & MAINTENANCE……….………………………………………………….………….12
7. DISPOSAL…………………………………………………………………………………………….….13
8. EC DECLARATION OF CONFORMITY……….………………………………………………..14
9. WARRANTY……………………………………………………………………………………..……..15
10. PRODUCT FAILURE……………………………………………………………………….…………16
11. WARRANTY EXCLUSIONS…………………………………………………………….………….17

3
1. SAFETY WARNINGS
General power tool safety warnings
WARNING Read all safety warnings, instructions, illustrations and
specifications provided with this power tool. Failure to follow all instructions
listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.
The term "power tool" in the warnings refers to your mains-operated (corded)
power tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distractions
can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodified
plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock if
your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplugging
the power tool. Keep cord away from heat, oil, sharp edges or moving parts.
Damaged
or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of electric
shock.
NOTE The term “residual current device (RCD)” can be replaced by the term “ground fault circuit
interrupter (GFCI)” or “earth leakage circuit breaker (ELCB)”.

4
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when operating
a power tool. Do not use a power tool while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating power
tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protective
equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the tool.
Carrying power tools with your finger on the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
clothing away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust extraction and collection
facilities, ensure these are connected and properly used. Use of dust collection
can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause severe
injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce the
risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power tool.
Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding of
moving parts, breakage of parts and any other condition that may affect the
power tool’s operation. If damaged, have the power tool repaired before use.

5
Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control
of the tool in unexpected situations.
5) Service
a) Have your power tool serviced by a qualified repair person using only
identical replacement parts. This will ensure that the safety of the power tool is
maintained.
Belt sander safety warnings
Hold the power tool by insulated gripping surfaces, because the sanding surface
may contact its own cord. Cutting a "live" wire may make exposed metal parts of
the power tool "live" and could give the operator an electric shock.
WARNING Contact with or inhalation of harmful / toxic dusts arising from sanding
painted surfaces, woods and metals can endanger the health of operator and
bystanders.
Take special care to guard against these dusts, including the following:
-All persons entering the work area must wear an approved mask specially
designed for protection against harmful / toxic dusts, in addition to using the
dust extraction facility, and keeping work area well ventilated.
-Children and pregnant women must not enter the work area.
-Do not eat, drink or smoke in the work area.
Any pre 1960 building may have paint containing lead on wood or metal
surfaces. If you suspect workpiece contains lead seek professional advice.
Some wood and wood type products especially MDF (Medium Density
Fibreboard) can produce dust that can be hazardous to your health. We
recommend the use of an approved face mask with replaceable filters when
using this machine in addition to using the dust extraction facility.

6
Hold the machine correctly using two hands and adopt a stable stance, make
sure that the mains cable is prevented from coming into contact with the
machine or getting caught up on other objects preventing completion of the
sanding pass.
This tool is intended to remove surface material using an abrasive medium.
Ensure that you have removed foreign objects such as nails and screws from
the workpiece before commencing sanding.
Do not use it for wet sanding, for dry sanding only.
Where possible, secure smaller workpieces to prevent them from moving
under the sander.
Do not force the sander, let the tool do the work at a reasonable speed.
Overloading will occur if too much pressure is applied and the motor slows
resulting in inefficient sanding and possible damage to the sander motor.
Do not use the dust collection box when sanding metal. The hot metal
particles could cause residual wood dust or the internal filter paper to catch
fire.
Do not continue to use worn, torn or heavily clogged sanding belts.
Do not touch the moving sanding belt.
If the replacement of the supply cord is necessary, this has to be done by the
manufacturer or his agent in order to avoid a safety hazard;

7
2. EXPLANATION OF SYMBOLS
In this manual and/or on the machine the following symbols are may
used:
Read instructions carefully
In accordance with essential applicable safety standards of European
directives
Class II machine –Double insulation –You don’t need any earthed
plug.
Faulty and/or discarded electrical or electronic apparatus have to be
collected at the appropriate recycling locations
Wear eye protection
Wear hearing protection

8
3. PART LIST
1) Front handle
2) Belt centralizing knob
3) Drive belt cover
4) On.off trigger switch
5) Lock-on button
6) Dust extraction outlet
7) Rear handle
8) Carbon brush cap
9) Speed adjuster

9
Type designation
Belt Sander
Rated voltage
220-240V~ 50Hz
Rated power input
900W
Speed, n0
120-340m/min
Sanding belt size
533x 76mm
Level of acoustic pressure LpA
89.0 dB(A), KpA=3dB(A)
Level of acoustic power LwA
100 dB(A), KwA=3dB(A)
Level of vibration ah
3.41m/s2 K=1.5m/s2
Protection class
II
4. Technical specification
Information:
The declared vibration total value has been measured in accordance with a
standard test method and may be used for comparing one tool with another;
The declared vibration total value may also be used in a preliminary
assessment of exposure.
Warning:
that the vibration emission during actual use of the power tool can differ
from the declared total value depending on the ways in which the tool is
used; and
of the need to identify safety measures to protect the operator that are
based on an estimation of exposure in the actual conditions of use (taking
account of all parts of the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to the trigger time).
Wear hearing protection.

10
5. ASSEMBLY AND USE
Selecting the right grade of sanding belt
Different grades of sanding belt can be purchased from the store where
you purchased the tool. Available grades are: Coarse, Medium and Fine.
Use a coarse grit to sand down rough finishes, medium grit to smooth the work
and fine grit to finish off.
It is best to make a trial run on a scrap piece of material to determine the
optimum grades of sanding belt for a particular job.
GRIT CHART
Grit
Type
Example of use
60 or less
Very Coarse
Material removal, heavy paint removal,
shaping wood
80 –100
Coarse
Paint removal, rough surface preparation (e.g.
non-planed wood)
120 –150
Medium
Surface preparation planed wood
180 –220
Fine
Sanding between coats
240 or more
Very Fine
Final finishing

11
Adjust the working speed by turning the knob on the front handle. We
recommend using a slow speed initially and then accelerating. The MIN marking is
the slowest speed and the MAX marking is the fastest speed.
Sanding
The sander can be used for most sanding operations on materials such as wood,
plastic, metal and painted surfaces.
WARNING : Don’t use this machine on plaster.
Wear safety goggles and dust mask.
Where possible, secure smaller workpiece to prevent them from moving under
the sander. Lower the sander in contact with the workpiece without pressure and
then start the sander.
Move the sander slowly over the surface of the workpiece, for best results use
the sander in a linear motion not circular. Using the sander in a circular motion
may result in the belt tracking slipping. Sand with the grain, in parallel over
lapping strokes.
To remove paint or smooth very rough wood, sand across the grain at 45º in two
directions, and then finish parallel with the grain. Use the front roller only to sand
corners or irregular shapes.

12
Lift the sander off the work before switching off. Remember to keep your hands
away from the moving belt, as it will continue to move for a short time after the
machine is switched off.
If there are still scratches on your work after sanding, try either of the following:
-Go back to a coarser grit and sand the marks out before recommencing with the
original choice or,
-Try using new sanding belt of the same grit to eliminate the unwanted marks before
progressing to a finer grit and finishing the job.
6. SERVICE & MAINTENANCE
Always disconnect the device before performing any adjustment or
maintenance operation. If the supply cord of this power tool is damaged, it must
be replaced by a specially prepared supply cord available through the service
organization.
Disconnect from the power supply immediately if the supply cord is damaged.
Take care not to expose this tool to the rain.
If the carbon brushes need to be replaced, have this done by a qualified repair
person (always replace the two brushes at the same time)
Cleaning
Avoid using solvents when cleaning plastic parts. Most plastic parts are
susceptible to damage from various types of commercial solvents and may be
damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
Lubrication
All the bearings in this tool are lubricated with a sufficient amount of high grade
lubricant for the life of the unit under normal operating conditions, therefore no
further lubrication is required.

13
7. DISPOSAL
CAUTION! This product has been marked with a symbol relating to
removing electric and electronic waste. This means that this
product shall not be discarded with household waste but that it
shall be returned to a collection system which conforms to the
European WEEE Directive. Contact your local authorities or ask for
advice on recycling. It will then be recycled or dismantled in order to reduce the
impact on the environment. Electric and electronic equipment can be hazardous
for the environment and for human health since they contain hazardous
substances.

14
8. EC DECLARATION OF CONFORMITY
EC Declaration of conformity
BUILDER SAS
32, rue Aristide Bergès - ZI 31270 Cugnaux –France
Declares that the machine
BELT SANDER
FPB900
Serial number: 20210904945-20210905444
Is in conformity with the European Directives:
Machine Directive 2006/42/EC
EMC Directive 2014/30/EU
RoHS Directive 2011/65/EU+(EU) 2015/863
Noise directive 2000/14/EC +Annex VI & 2005/88/EC
This product is also in conformity with the following standards:
EN 62841-1:2015+AC:15
EN 62841-2-4:2014 AC:15
EN55014-1:2017+A11:2020
EN55014-2:2015
EN61000-3-2:2019
EN61000-3-3:2013+A1:2019
Responsible of the technical file: Mr Olivier Patriarca
Cugnaux, 16/07/2021
Philippe MARIE / PDG

15
9. WARRANTY
The manufacturer guarantees the product against defects in material and
workmanship for a period of 2 years from the date of the original purchase. The
warranty only applies if the product is for household use. The warranty does not
cover breakdowns due to normal wear and tear.
The manufacturer agrees to replace parts identified as defective by the
designated distributor. The manufacturer does not accept responsibility for the
replacement of the machine, in whole or in part, and/or ensuing damage.
The warranty does not cover breakdowns due to:
insufficient maintenance.
abnormal assembly, adjustment or operations of the product.
parts subject to normal wear and tear.
The warranty does not extend to:
shipping and packaging costs.
using the tool for a purpose other than that for which it was designed.
the use and maintenance of the machine done in a manner not
described in the user manual.
Due to our policy of continuous product improvement, we reserve the right to
alter or change specifications without notice. Consequently, the product may be
different from the information contained therein, but a modification will be
undertaken without notice if it is recognized as an improvement of the preceding
characteristic.
READ THE MANUAL CAREFULLY BEFORE USING THE MACHINE.
When ordering spare parts, please indicate the part number or code, you can find
this in the spare parts list in this manual. Keep the purchase receipt; without it,
the warranty is invalid. To help you with your product, we invite you to contact us
by phone or via our website:
+33 (0)9.70.75.30.30
https://services.swap-europe.com/contact
You must create a "ticket" via the web platform.
Register or create your account.
Indicate the reference of the tool.
Choose the subject of your request.
Describe your problem.
Attach these files: invoice or sales receipt, photo of the identification plate (serial
number), photo of the part you need (for example: pins on the transformer plug
which are broken).

16
10. PRODUCT FAILURE
WHAT TO DO IF MY MACHINE BREAKS DOWN?
If you bought your product in a store:
•Empty the fuel tank.
•Make sure that your machine is complete with all accessories supplied,
and clean! If this is not the case, the repairer will refuse the machine.
•Go to the store with the complete machine and with the receipt or
invoice.
If you bought your product on a website:
•Empty the fuel tank.
•Make sure that your machine is complete with all accessories supplied,
and clean! If this is not the case, the repairer will refuse the machine.
•Create a SWAP-Europe service ticket on the site: https://services.swap-
europe.com When making the request on SWAP-Europe, you must attach the
invoice and the photo of the nameplate (serial number).
Contact the repair station to make sure it is available before dropping off the
machine.
Go to the repair station with the complete machine packed, accompanied by the
purchase invoice and the station support sheet downloadable after the service
request is completed on the SWAP-Europe site
For machines with engine failure from manufacturers BRIGGS & STRATTON,
HONDA and RATO, please refer to the following instructions.
Repairs will be done by approved engine manufacturers of these manufacturers,
see their site:
•http://www.briggsandstratton.com/eu/fr
•http://www.honda-engines-eu.com/fr/service-network-
page;jsessionid=5EE8456CF39CD572AA2AEEDFD290CDAE
•https://www.rato-europe.com/it/service-network
Please keep your original packaging to allow for after-sales service returns or
pack your machine with a similar cardboard box of the same dimensions.
For any question concerning our after-sales service you can make a request on
our website https://services.swap-europe.com
Our hotline remains available at [phone].

17
11. WARRANTY EXCLUSIONS
THE WARRANTY DOES NOT COVER:
•Start-up and setting up of the product.
•Damage resulting from normal wear and tear of the product.
•Damage resulting from improper use of the product.
•Damage resulting from assembly or start-up not in accordance with the user
manual.
•Breakdowns related to carburetion beyond 90 days and fouling of
carburetors.
•Periodic and standard maintenance events.
•Actions of modification and dismantling that directly void the warranty.
•Products whose original authentication marking (brand, serial number) has
been degraded, altered or withdrawn.
•Replacement of consumables.
•The use of non-original parts.
•Breakage of parts following impacts or projections.
•Accessories breakdowns.
•Defects and their consequences linked to any external cause.
•Loss of components and loss due to insufficient screwing.
•Cutting components and any damage related to the loosening of parts.
•Overload or overheating.
•Poor power supply quality: faulty voltage, voltage error, etc.
•Damages resulting from the deprivation of enjoyment of the product during
the time necessary for repairs and more generally the costs related to the
immobilization of the product.
•The costs of a second opinion established by a third party following an
estimate by a SWAP-Europe repair station
•The use of a product which would show a defect or a breakage which was
not the subject of an immediate report and/or repair with the services of
SWAP-Europe.
•Deterioration linked to transport and storage*.
•Launchers beyond 90 days.
•Oil, petrol, grease.
•Damages related to the use of non-compliant fuels or lubricants.
* In accordance with transport legislation, damage related to transport must be
declared to carriers within 48 hours maximum after observation by registered
letter with acknowledgement of receipt.
This document is a supplement to your notice, a non-exhaustive list.
Attention: all orders must be checked in the presence of the delivery person. In
case of refusal by the delivery person, it you must simply refuse the delivery and
notify your refusal.
Reminder: the reserves do not exclude the notification by registered letter with
acknowledgement within 72 hours.
Information:
Thermal devices must be wintered each season (service available on the SWAP-
Europe site). Batteries must be charged before being stored.

18
BUILDER SAS
32, rue Aristide Bergès - ZI 31270 Cugnaux –France
Made in PRC 2021