Ferrofish Verto 32 User manual

OWNERS MANUAL
Version 1.0
Ferrofish
Advanced Audio Applications
Brüderstr. 10, D-53545 Linz (Rhine)
Germany www.ferrofish.de

2
01. Table of contents
02. Safety instructions and warnings 3
03. Introduction 5
03.1 Scope of delivery 5
04. Product Description 6
04.1 Description of the front panel 6
04.1.1 Verto 32 and 64 6
04.1.2 Verto MX 6
04.2 Description of the rear panel 7
04.2.1 Verto 32 and 64 7
04.2.2 Verto MX 8
04.3 Clocking 8
05. Operation (important) 8
06. Technical specifications 9
07. Optional accessories and spare parts 9
08. Troubleshooting 10
09. Legal information 11
09.1 Warranty 11
09.2 Disclaimer of liability 11
10. Declarations of conformity, etc. 12
10.1 CE conformity - EMC 12
10.2 CE conformity - RoHS II 12
10.3 FCC Declaration 12
10.4 Waste disposal (WEEE) 13
10.5 Service & Maintenance 13

3
02. Safety instructions and warnings
IMPORTANT SAFETY INSTRUCTIONS
Safety symbols used in this manual:
This symbol is an alert that there are important maintenance
and operating instructions in the literature.
This symbol warns the user of uninsulated, potentially dangerous voltage inside the unit
that can cause an electric shock.
This symbol warns the user that the output connectors of the power supply contain
voltages that can cause dangerous, potentially lethal shocks.

4
• Read these Instructions • Keep these instructions
• Heed all warnings • Follow all instructions
1. Do not use this device near water.
2. Clean only with a dry cloth. Do not spray liquid cleaner onto the faceplate or into the
ventilation slots. This may damage the front panel or cause a dangerous condition.
3. Only install in accordance with the manufacturer’s instructions.
4. Do not install or operate near heat sources such as stoves, radiators or other devices
that may produce heat.
5. NEVER compromise the functioning of the power plug’s ground connection. When
the provided plug doesn’t fit into the outlet, please consult a qualified electrician for
assistance.
6. Use power adaptors and accessories specified by the manufacturer only.
7. Protect the power cord from being pinched or stepped on.
8. Unplug this device during lightning storms, or when not in use for extended periods of time.
9. Refer all servicing to qualified service personnel only. Servicing is required when the
device has been damaged in any way. For example when liquids have been spilled on
the device, objects have fallen onto it, or the device itself has been dropped. Servicing
is also essential when the device no longer functions normally or has been exposed
to rain or moisture.
10. This unit generates heat during normal operation. Use it in a well ventilated environ-
ment with at least 1RU space between any other equipment.
11. This product in combination with headphones or other external amplifiers and
speakers may produce sound levels that could lead to permanent hearing damage.
Do not operate at high or uncomfortable volume levels for a long time. If you are
experiencing ringing in your ears, a loss of high frequency sound information or
other hearing loss, please contact an audiologist immediately.
12. WARNING: To reduce the risk of an electric shock or fire, do not expose the device
to rain or moisture.
13. The power supply of this audio device may cause electronic interference to surround-
ing equipment. If you find that this or any nearby unit is malfunctioning, try resetting
the device, relocating it, or getting an electrician to install a powerline conditioner.

5
03. Introduction
Dear Customer,
Thank you for purchasing our product. We are very pleased that you have chosen the
Verto series from our product range. It is designed as an easy format converter between
ADAT (Verto 32 & 64) or MADI (Verto MX) and the DANTE protocol. We have developed
three different models so that you can choose the one most suited to your needs.
The Verto 32 and 64 have 32x32 and 64x64 I/O channels respectively, for an easy in-
tegration of devices with ADAT ports. When using MADI devices the Verto MX is the
perfect solution; offering both optical and coaxial MADI I/O ports. All Verto models also
incorporate MIDI I/O for sending and/or receiving MIDI commands via the MADI (Verto
MX only) and DANTE data streams. This means it’s possible to transmit 64x64 audio
channels plus MIDI commands up to 2km with the Multimode MADI module. It is even
possible to bridge distances of up to 10km via MADI glass fiber with the optional sin-
gle-mode MADI module, installation of which can easily be done by the end-user.
We sincerely hope that you will enjoy using your Verto as much as we enjoyed devel-
oping it. Should you have any suggestions, praise or criticism for us, please visit us on
Facebook or at www.ferrofish.de - a handwritten letter is of course also happily received.
Warm greetings from Linz near the river Rhine.
The Ferrofish Team
03.1 Scope of Delivery
This package includes:
1x Verto device
1x Instructions (German & English)
1x Power supply 12V
1x LC / SC adapter cable (Verto MX only)
1x Locking plate for ADAT cables including mounting accessories (Verto 32 only)
2x Locking plate for ADAT cables including mounting accessories (Verto 64 only)
Optional accessories and spare parts can be found at topic 07.

6
04. Product Description
The Verto series of devices serve as converters for your ADAT or MADI devices. They
make the integration of existing gear into a DANTE environment quick and easy. All
essential settings are made via DANTE. The fanless and low heat-generating design also
makes the Verto series perfect for installation in acoustically sensitive environments.
04.1 Description of the front panel
04.1.1 Verto 32 and 64
The status LEDs and operating elements are explained as follows (from left to right):
1. DANTE LED: The DANTE LED indicates the state of the DANTE network. When the LED
is lit permanently, a connection to the DANTE network exists. A flashing LED indicates
that DANTE has muted all channels. This may have been caused by e.g. a missing net-
work signal or a change of the sample rate in the DANTE network.
2. ADAT Inputs (Verto 32: 1-4, Verto 64: 1-8): These status LEDs indicate when an ADAT
input has been successfully synchronized to the DANTE network’s word clock. These
LEDs are not input indicators. If the LED flashes, the synchronization process has failed.
If it is lit continuously, interrupted by short flickering, both devices are „master“.
3. Power LED: The LED lights up continuously when the device is switched on and ready
for operation. It flashes slowly when the device is booting. If you hold down the power
button, the LED will rapidly flash to indicate the imminent shutdown of the device.
4. Power button: This button turns the Verto on and off. To switch off the unit, press
and hold the button for at least 3 seconds.
04.1.2 Verto MX
The status LEDs and operating elements are explained as follows (from left to right):
1. DANTE LED: The DANTE LED indicates the state of the DANTE network. When the
LED is lit permanently, a connection to the DANTE network exists. A flashing LED

7
indicates that DANTE has muted all channels. This may have been caused by e.g. a
missing network signal or a change of the sample rate in the DANTE network.
2. MADI Input (optical): This status LED is permanently lit when the optical MADI input
receives a valid signal and the Verto has successfully synchronized to it. It is not an input
indicator for MADI signals. If the LED flashes, the synchronization process has failed. If it
is lit continuously, interrupted by short flickering, both devices are „master“.
3. MADI Input (coaxial): This status LED is permanently lit when the coaxial MADI
input receives a valid signal and the Verto has successfully synchronized to it. The
LED is not an input indicator for MADI signals. If the LED flashes, the synchronization
process has failed. If the LED is lit continuously, interrupted by short flickering, both
devices are „master“. If the LED is lit with half brightness a valid signal is detected at
both MADI inputs, but MADI optical is used.
4. Sample rate - LEDs: These LEDs show the sample rate of the DANTE network.
5. Power LED: The LED lights up continuously when the device is switched on and ready
for operation. It flashes slowly when the device is booting. If you hold down the pow-
er button, the LED will rapidly flash to indicate the imminent shutdown of the device.
6. Power button: This button turns the Verto on and off. To switch off the unit, press
and hold the button for at least 3 seconds.
If a valid MADI signal is present on the optical and the coaxial port at the same
time, the optical port is automatically used for conversion to DANTE. If you
want to use the coaxial MADI input please remove the optical MADI cable.
04.2 Description of the rear panel
04.1.1 Verto 32 and 64
The connections of the Verto 32 and 64 are explained as follows (from left to right):
1. Power supply: Connect the power supply here and lock it with the coupling nut.
Thus, the plug cannot slip out unintentionally.
2. ADAT I/Os: Connect your ADAT devices using optical Toslink cables. The black flaps
are ADAT inputs, the white flaps are outputs.
3. MIDI I/O: Both the MADI and the DANTE data streams can be used to send and receive
MIDI messages. These are embedded in the DANTE or MADI data stream.
4. WORDCLOCK I/O: Transmit word clock to or from the Verto using these connectors.
We recommend setting the connected devices to “slave“.

8
5. DANTE (PRI/SEC): Use this port to connect the unit to a DANTE network. Use a com-
mercially available Ethernet cable (at least CAT5) and connect it to the PRI (primary) port.
04.2.2 Verto MX
The connections of the Verto MX are explained as follows (from left to right):
1. Power supply: Connect the power supply here and lock it with the coupling nut.
Thus, the plug cannot slip out unintentionally.
2. MADI I/O (coaxial): Use these connectors for devices with coaxial BNC MADI.
3. MADI I/O (optical): Connect your optical fiber MADI equipment to these ports. Depend-
ing on the specification of your MADI equipment, this can be done either directly at
the device via the LC connector or via the included SC-LC adaptor.
4. MIDI I/O: Both the MADI and the DANTE data streams can be used to send and receive
MIDI messages. These are embedded in the DANTE or MADI data stream.
5. WORDCLOCK I/O: Transmit word clock to or from the Verto using these connectors.
We recommend setting the connected devices to „slave“.
6. DANTE (PRI/SEC): Use this port to connect the unit to a DANTE network. Use a com-
mercially available Ethernet cable (at least CAT5) and connect it to the PRI (primary) port.
04.3 Clocking (important!)
Generally, in a network of DANTE devices, at least one of them must be set to „master“.
Therefore set all devices connected to the Verto to „slave“.
If there are several DANTE devices connected to a network, then set your preferred de-
vice inside the DANTE controller to „Preferred Master“.
05. Operation
Operating the Verto series is simple. Connect the included power supply to the corre-
sponding connector on the back of the Verto.
Connect the ADAT (Verto 32 and 64) or MADI (Verto MX) devices to their respective
ports on the back panel. Lastly, connect an Ethernet cable (at least CAT5) to an existing
DANTE network or to a computer with DANTE Virtual Soundcard installed and the op-
tionally available DANTE Controller application (recommended).

9
06. Technical specifications
DANTE I/O ∙ 2x Ethernet (PRI/SEC) sockets, 1GBit
∙ 64x64 channel Brooklyn II board built-in
ADAT I/O
(Only Verto 32 & 64)
∙ 4x ADAT Input + 4x ADAT Output, optical TOSLINK (Verto 32)
∙ 32x32 channels at 48kHz, 16x16 channels at 96kHz
∙ 8x ADAT Input + 8x ADAT Output, optical TOSLINK (Verto 64)
∙ 64x64 channels at 48kHz 32x32 channels at 96kHz
MIDI I/O ∙ MIDI Standard 1.0 / 1996
∙ 2x DIN female 5pin In/Out for embedding / de-embedding
MIDI-over-MADI messages
MADI I/O
(Verto MX only)
∙ AES 10, 2x optical LC port, 2x coaxial BNC port
∙ 64x64 channels at 48kHz, 32x32 channels at 96kHz, 16x16
channels at 192kHz
Wordclock ∙ 2x BNC In/Out, 75 Ohm termination set to on by default.
Can be changed from software via DANTE.
Fuse ∙ Polyfuse internal, self-resetting
Power consumption ∙ 14.4VA (1.2A at 12V)
Temperature range ∙ +5°C to +45°C
Humidity ∙ <75%, non-condensing
Dimensions ∙ 22 x 9 x 4,5 mm (without rack ears)
Weight ∙ 0,9 kg
07. Optional accessories and spare parts
The following accessories and spare parts are available for the Verto series:
Description Item code For VERTO Series
19“ Rack mountain kit, metal
(for mounting 1 x Verto in a 19” rack-space)
7008 32, 64 and MX
Multi-range Power Supply 12V (EU) 7023 32, 64 and MX
ADAT Cable Locking Plate 7027 32 and 64
MADI Singlemode Module 7020 MX
MADI SC / LC Adapter 7026 MX
The accessories and the spare parts can be purchased
from the dealer or the distributor as well as at www.ferrofish.de.

10
08. Troubleshooting
Error Possible cause Troubleshooting
POWER LED does not light Power supply not plugged in or
defective
Check the power supply
The device is switched off Switch on the device with the
power button. Seriously.
POWER LED flashes quickly Power button pressed The power LED flashes quick-
ly when the power button is
pressed on a switched-on de-
vice.
POWER LED flashes slowly The Verto unit is booting in the
start-up process
Wait approx. 20 seconds for the
boot-up-sequence to finish.
DANTE LED does not light up
(see Power LED)
Mains cable defective or the
wrong type (crossed) is used
Use a different network cable
Verto is booting Wait approximately 20s until the
boot process is finished
Error in the DANTE network Check the functioning of the
DANTE network.
DANTE LED is flashing No connection to the Dante
network
Check the functioning of the
DANTE network.
Device is „slave“, but no “Mas-
ter“ was found on the DANTE
network.
Set a device in the DANTE net-
work to „Master“
Sample rate on the network
has been changed
When changing the sample rate,
the outputs are muted briefly.
MADI coaxial LED lights low Both ports (opto & coax) re-
ceive valid signal
Both signals are valid, but the
optical port is automatically used
for DANTE.
This is a status indication, not
an error.
ADAT Input LED flashes A sync process has failed Set all connected ADAT devices
to „Slave“.
ADAT Input LED is lit constantly,
regularly interrupted by flick-
ering
Both devices are „Master“. Set all connected ADAT devices
to „Slave“.

11
09. Legal information
09.1: Warranty
Every VERTO is thoroughly checked and tested. Ferrofish grants a warranty of two years
after purchase thru an authorized dealer or distributor. The invoice is needed as a proof-
of-purchase.
In case of an permanent malfunction or any other defect under warranty that can’t be
fixed by support, please contact your dealer and inquire a repair under warranty. Damages
caused by improper installation or inappropriate usage are not covered by warranty.
Fixing these damages will be liable to pay costs.
Claim for damages of any kind, in particular consequential damage or loss are not
covered. A liability exceeding the merchandise value of an VERTO is also not covered.
We refer to the general terms and conditions of Ferrofish GmbH.
09.2: Disclaimer of liability
This documentation has been created to the best of knowledge and belief on the current
state of technology. Ferrofish assumes no responsibility either expressed or implied for
the accuracy, completeness and correctness of this documentation. In no event Ferrofish
GmbH will be liable for any kind of data loss or data error caused thru the use of our
product or documentation.
In particular Ferrofish GmbH excludes liability upon consequential damage caused by the
use of this product or the documentation.
All trademarks used in this manual are property of their respective owners and are used
for descriptive purpose only. This also applies to text passages, where appropriate copy-
right marks or trademarks are missing.
Although the contents of this Owner’s Manual have been checked for errors, Ferrofish
cannot guarantee that it is correct. Ferrofish does not accept responsibility for any mis-
leading or incorrect information within this manual. Copying any part of the manual or
any commercial exploitation of these media without prior permission from Ferrofish is
strictly prohibited. Ferrofish reserves the right to change specifications at any time with-
out prior notice. Product and documentation is subject to the terms and conditions of
Ferrofish GmbH at the latest state.

12
10. Declarations of conformity, etc.
10.1: CE conformity - EMC
This device fully complies to all harmonized standards for the approximation of laws of the
member states for the electromechanical compatibility (EMC:2014/30/EU) and European
Low Voltage Directive 2014/35/EU.
10.2: CE conformity - RoHS II
This device has been produced with lead free solder according to the EU directive
2011/65/EU and therein contained maximum permissible values for hazardous substances
found in electronic devices.
10.3: FCC Declaration
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference, and
(2) This device must accept any interference received, including interference that may
cause undesired operation.
Responsible Party in USA: Synthax United States, 6600 NW 16th Street, Suite 10,
Ft Lauderdale, FL 33313 T.:754.206.4220
Trade Name: Ferrofish, Model Number: VERTO
This equipment has been tested and found to comply with the limits for a Class
B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference in a residential in-
stallation. This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful inter-
ference to radio communications. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
•Reorient or relocate the receiving antenna.
•Increase the separation between the equipment and receiver.
•Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
•Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any modifications or other changes to this unit not approved by the party
responsible for compliance could void the user’s authority to operate this equipment.

13
10.4: Waste disposal (WEEE)
According to common law of the EU states directive RL2002/96/EG (WEEE – Directive on
Waste Electrical and Electronic Equipment) this product must be recycled after final use
and/or end of its lifetime.
In case a disposal of electronic waste is not possible, the recycling can also be done by
the manufacturer. For this the device has to be sent free to the door to: Ferrofish GmbH,
Brüderstraße 10, D-53545 Linz / Rhein, Germany. Not prepaid shipping’s will be rejected
and returned on the sender’s costs.
10.6: Service & Maintenance
No serviceable parts inside. Do not open this device.

14
NOTES

15

16
• Consult the dealer or an experienced radio/TV technician for help.
WARNING: Any modifications or other changes to this unit not approved by the party
responsible for compliance could void the user’s authority to operate this equipment.
10.4: Waste disposal (WEEE) ???
10.5: Maintenance ???
10.6: Service ???
Ferrofish
Advanced Audio Applications
Brüderstr. 10, D-53545 Linz (Rhine)
Germany www.ferrofish.de