Ferroli ZU0800009 Assembly Instructions

Installation & User Instructions
Part number: ZU0800009
Radio Thermostat Clock
80.10.1375.7_feeling_ks_fer_en.indd 1 18.04.2013 11:25:42

2
Table of contents
Safety instructions............................... 3
Product details..................................... 4
Installation and assembly..................... 7
Operating and adjustment.................. 15
Conguration ..................................... 18
Initial start-up .................................... 19
Settings ............................................. 25
Operating modes ............................... 29
Operating status ................................ 36
User menu/Conguration ................... 39
Installation menu ............................... 40
80.10.1375.7_feeling_ks_fer_en.indd 2 18.04.2013 11:25:42

3
Safety instructions
Danger from electric shock!
The connection and installation of electrical devices may only be carried out
by a qualied electrician.
DANGER
• It is imperative to observe the generally applicable safety measures, e.g. before starting any work
on the appliance, switch off power supply and secure against switching on.
• Interventions in and changes to the device result in the voiding of the warranty claim.
• Observe your national regulations and the respective safety provisions.
80.10.1375.7_feeling_ks_fer_en.indd 3 18.04.2013 11:25:42

4
A B
C
D
E
F
Product details
The radio thermostat clock is a 7 day radio frequency
(RF) wireless thermostat/ timer which communicates
with a special receiver designed to t in the clock
aperture of the boiler casing.
The radio thermostat clock is battery powered and can
be sited wherever conventional room thermostats would
normally be sited. See installation locations information
on page 7.
The radio thermostat clock is a room thermostat and
clock of highly advanced technology. The device is
wireless and controls the heating via radio, providing
both time control and comfortable room temperatures.
Assembly description
AMoveable sliding cover
BKeys for manual override
function
CWindow
DKeyboard
EBattery compartment
FDisplay
80.10.1375.7_feeling_ks_fer_en.indd 4 18.04.2013 11:25:43

5
Technical data – RF Set, Transmitter
Power supply: 2 x 1.5 V AA LR6 alkaline batteries
Battery service life: 2 years (depending on switching frequency)
Room temperature display resolution: 0.1ºC
Temperature setting display: Program: +5ºC…+32ºC (0.5ºC steps)
Frost protection: 5ºC (adjustable 3ºC…7ºC)
Time setting resolution: Time of day: 1 minute
Program: 30 minutes
Programming: weekly program with up to 48 time and temperature programs
changes
Pre-programmed programs: 4 + 1 user-dened
RF signal: 868.3 MHz
RF signal range: Indoor 30 m (2 walls + 1 ceiling)
Protection class / type: II / IP40
Operating temperature range: Max. 45ºC
Operating humidity range: 10% to 90% RH non-condensing
Dimensions H x W x D (mm): 87 x 154 x 27
80.10.1375.7_feeling_ks_fer_en.indd 5 18.04.2013 11:25:43

6
Technical data – RF Set, Receiver
Power supply: 230 V +/-10% 50-60 Hz
Switching output: SPDT (potential-free)
Switching capacity: 5 (1) A 250 V AC
RF signal: 868.3 MHz
RF signal range: Indoor 30 m (2 walls + 1 ceiling)
Protection class / type: II / IP20
Operating temperature range: Max. 45ºC
Operating humidity range: 10% to 90% RH non-condensing
Dimensions H x W x D (mm): 60 x 60 x 32
80.10.1375.7_feeling_ks_fer_en.indd 6 18.04.2013 11:25:43

7
1.5 m
Installation and assembly
General information
80.10.1375.7_feeling_ks_fer_en.indd 7 18.04.2013 11:25:43

8
Modena C HE
80.10.1375.7_feeling_ks_fer_en.indd 8 18.04.2013 11:25:43

9
Wiring diagram
These spades
connect to
terminals 1 & 2 at
the clock
Remove Link and
connect leads to
terminals 3 & 4 at
the receiver
White
L
White
N
Radio Thermostat
Clock Receiver
80.10.1375.7_feeling_ks_fer_en.indd 9 18.04.2013 11:25:44

10
Wiring Connections
1 - Live (Brown)
2 - Neutral (Blue)
3 - Switched circuit (White #1)
4 - Switched circuit (White #2)
5 - No connection required
Commissioning, please turn to page 11.
Receiver Button
LED
Installation of the receiver
M
~
1
23
45
80.10.1375.7_feeling_ks_fer_en.indd 10 18.04.2013 11:25:44

11
Receiver Button
Installation of the radio link
The transmitter and receiver are pre-commissioned. If the radio link doesn‘t work correct,
follow the sequence of commissioning.
Press and hold the black button of the receiver until the LED light has ashed twice. Release the
button and the LED light will remain illuminated.
Press and hold MODE-button and SET-button of the transmitter at the same time for more than 3
seconds to enter into the User menu. Then press the OK-button until RF Comm is displayed.
80.10.1375.7_feeling_ks_fer_en.indd 11 18.04.2013 11:25:44

12
Press upper +button (–button disables the RF signal) to enable an continous RF signal. The receiver
LED will go out as soon as a signal from the transmitter is received. Then press the OK-button, the
radio link between transmitter and receiver is now established. Press the ESC-button to return to Auto
mode.
Receiver: When operating in heating mode and an ON signal is received, the LED illuminates
continously. When an OFF signal is received, the LED is off (and ashes periodically at longer
intervals). Is no valid radio signal received from the transmitter for more than one hour (e.g. low
battery) the emergency operating mode will be activated. The LED ashes every 0,5 seconds.
80.10.1375.7_feeling_ks_fer_en.indd 12 18.04.2013 11:25:45

13
Open housing Wall mounting
80.10.1375.7_feeling_ks_fer_en.indd 13 18.04.2013 11:25:45

14
Only use 2 x 1.5 V type AA.
click!
click!




Close housing Insert batteries
80.10.1375.7_feeling_ks_fer_en.indd 14 18.04.2013 11:25:46

15
Operating and adjustment
Operating information
• Flashing texts signal the need for an entry. If no button is pressed for 2 minutes, the device reverts
to the Automatic mode.
• All settings need to be conrmed with OK.
• All settings saved will remain in the memory.
• The histogram shows the programmed temperature prole
7 – 14°C = displayed as one segment
15 – 24°C = one segment displays 1°C
over 24°C = one segment displays 2°C
80.10.1375.7_feeling_ks_fer_en.indd 15 18.04.2013 11:25:46

16
ACurrent week day
BBattery
CRF signal
DCurrent time
ESet temperature
FOff mode
GHistogram over 24 hours
HCurrent temperature
IOperating mode
JStatus indication
KCurrent date
Display
A C
D
E
F
G
H
I
J
K
B
80.10.1375.7_feeling_ks_fer_en.indd 16 18.04.2013 11:25:47

17
Function keys
A+/– buttons used to increase/decrease
temperatures.
BOK-button to conrm settings and go to the
next step.
CMODE-button to select from the available
operating modes.
DESC-button used for ON/OFF, go one step back
in menu or return to main menu by pressing
the button more than 3 seconds.
ESET-button for settings following
commissioning.
F+/– buttons used to increase/decrease hours,
days and events.
GRESET-button to return to factory settings. The
programs are retained in the case of a reset.
The date and time must be set again. Press
reset button with a blunt object (pen).
A
C
E
B
F
G
D
80.10.1375.7_feeling_ks_fer_en.indd 17 18.04.2013 11:25:47

18
Conguration
General information
For the use of this manual you must observe the
following informations:

D
A
B
C
ASequence of operation
BPressed buttons are shown in black.
CFlashing elements are shown in black
DFixed elements are shown in grey
• Buttons which can be pressed during an
action are shown in black. The related display
is also shown in black.
• Follow exactly the numbers of the sequence
of operation.
• The conguration of the device is described
based on conguration.
• After starting the device for the rst time,
follow the menu for a correct conguration of
the device.
• Following commissioning, you can also
change the conguration by pressing the
SET-button.
80.10.1375.7_feeling_ks_fer_en.indd 18 18.04.2013 11:25:47

19
Initial start-up
Set date and time
Sequence for setting the date and time during initial start-up.
15/6/2008 appears as factory default.
To set the date and time after initial start-up press the SET-button, then choose Date or Time Menu
with the upper +/– buttons and conrm with OK.
80.10.1375.7_feeling_ks_fer_en.indd 19 18.04.2013 11:25:48

20
The time is set in the same way as the date.
80.10.1375.7_feeling_ks_fer_en.indd 20 18.04.2013 11:25:49