Fike 20-1343 User manual

DESCRIPTION
The 20-1343 Addressable pull station is a non-coded, dual-action manual pull station with a
key-lock reset feature. It provides Fike intelligent fire alarm control panels (FACP) with one
addressable alarm initiating input. The addressable module is housed inside the pull station.
The 20-1343 will automatically operate in Eclipse™ protocol. Eclipse™ is a patented High Speed
Communications Protocol. Refer to the FACP installation manual to determine if Eclipse™ protocol
is supported. No selection is required in the Pull Station. The 20-1343 meets the ADAAG controls
and operating mechanisms guidelines (section 4.1.3[13]), and the ADA requirement for a 5
pound maximum pull force to activate the pull station. Operating instructions are molded into
the pull station handle along with Braille text. Molded Terminal numbers are also present.
RATINGS
Normal Operating Voltage: 15 to 30VDC
Standby Current: 370 µA Maximum Average (continuous broadcasts)
Temperature Range: 32°F to 120°F (0°C to 49°C).
Relative Humidity Range: 10% to 93% Non-condensing.
Maximum Alarm Current: 2.0mA (red Led on)
INSTALLATION
The 20-1343 Addressable pull station can be semi-flush mounted on a standard single-gang,
double-gang or 4-inch (10.16 cm) square electrical box.
OPERATION
To activate the dual-action pull station, push in and pull down on the handle. The word ACTIVAT-
ED appears after the handle is pulled down. This will remain until the pull station is reset.
The pull station includes one Single Pole, Single Throw (SPST) Normally Open (N/O) switch
which closes upon activation of the pull station.
RESETTING THE PULL STATION
1. Insert the key into the lock and rotate 1/4turn counterclockwise.
2. Open the door until the handle returns to normal.
3. Close and lock the door.
NOTE: Closing the door automatically resets the switch to the “Normal” position. Opening the
door will not activate or deactivate the alarm switch.
CAUTION: Do not detach the door of the pull station during installation. The door of the pull
station cannot be reattached to the backplate after the backplate has already been installed
onto an electrical box.
P0261-00
SLC
SLC
STRIP GAUGE
1 2 3 4
FROM
FACP
TO NEXT
ADDRESSABLE
DEVICE
P0105-01
WIRING
CAUTION
Install the Fike 20-1343 addressable pull station in accordance with these instructions,
applicable NFPA standards, national and local Fire and Electrical codes and the requirements
of the AHJ (Authority Having Jurisdiction). Regular testing of the devices should be con-
ducted in accordance with the appropriate NFPA standards. Failure to follow these directions
may result in failure of the device to report an alarm condition. Fike is not responsible for
devices that have been improperly installed, tested or maintained.
ADA COMPLIANCE
For ADA compliance, if the clear floor space only allows forward approach to an object, the
maximum forward reach height allowed is 48 inches (121.92 cm). If the clear floor space al-
lows parallel approach by a person in a wheelchair, the maximum side reach allowed is 54
inches (137.16 cm).
20-1343
Addressable Pull Station
(over for Programming information)
20-1343 Addressable Pull Station
Document 52121 I56-3020-001
I56-3020-001
Document 52121
R

SETTING THE 20-1343 ADDRESS
Set the address for the pull station by using the IR configuration tool (model number EA-CT).
Only one device per address is allowed. Multiple modules may not be set to the same address
on the Signaling Line Circuit. Once the address is set, record it in the space provided on the
product ID label located inside the pull station.
NORMAL
ACTIVATED
4 3 2 1
UL Approved Label Here
LOOP
NBG-12Series
NON-CODED
FIREALARMBOX
LISTED
23424
REFERTODOCUMENT
P/N50997REV-A
AHDHDH
M
ADDRESS
L
U
PRODUCT IDENTIFICATION LABEL
ADDRESS
LOOP
ADDRESS
LOOP
LED
NOTE: OPENING THE PULL STATION DOOR WILL NOT ACTIVATE
OR DEACTI
VATE THE ALARM SWITCH.
NOTE: LED IS VISIBLE THROUGH TRANSLUCENT HANDLE.
P0239-02