Filmcity FC-A7RS-Kit User manual

1
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that
is listed below.
A7R II Camera Cage kit (FC-A7RS-KIT)
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or transmied by any form or by any means,
electronic, mechanical, photo-copying, recording, or otherwise, except as may be expressly permied by the applicable copyright
statutes or in wring by the Publisher.
Assembly Manua l
Camera cage Top Handle Rod Adapter Sliding base plate Cable clamp
2x150mm female rods
2x150mm male rods MB-600 Matte Box DP 500 Follow Focus

2
NOTE: If the french ag remains loose even
aer ghtening the knob, then slightly
ghten the allen bolt as shown.
 Now wrap Knicker on the conversion ring
of Mae Box.
 Insert french ag to the top of Mae Box
and ghten it with screws. In the same
way, insert side ags into the slots
provided on both sides and secure them
with screws.
 You can easily insert the lter holders as
shown in the image. The Filter tray can be
rotated 180 degree.
 The aluminum made Front Adapter
aaches mae box to the 15mm rods. Set
the mae box at any posion on the rods
by loosening the knob and sliding along the
rails, re-ghten to secure.
The Front Adapter also features height
adjustment up to 2.5cm increasing
compability of Mae box to adapt dierent
camera lenses.
Mae Box Setup

3
 Slide-in the rod adapter into the sliding
plate and lock it.
 Now, put the camera into the cage, and
secure it properly with ¼”-20 locking
screw.
 Aach the quick release plate of your
tripod head with sliding base plate and
ghten it with the help of screw driver.
Now mount the sliding base plate on uid
head and secure it properly with the help
of knob.
 Put the quick release plate onto the cage
and ghten it with locking screw. Then
mount the cage onto the rod adapter, and
make sure the knob is securely fastened.
NOTE: You can aach the 150mm male rods
at the front to extend the rods for mounng
your mae box, follow focus and handles etc.
Camera Cage Setup
Insert two 15mm rods into the Rod adapter,
and ghten the Knobs on both sides of the
Rod adapter.

4
NOTE: You can mount handle at dierent
posions – front / back / side. To do this,
loosen the screw with the help of screw driver
and set the posion as per your requirement,
make sure to properly secure it.
 Mount the top handle to the Cage as
shown in the photo, ghten the knob to
secure.
 Wrap the Flexible gear ring around the
lens, cut to size (if needed) and ghten the
gear properly. Then aach the follow focus
onto the rails and align it with the gear
ring. Tighten the knob to secure properly.
 Now aach the mae box to the front of
rods, align the knicker with the lens barrel
and ghten the knob.
 Now the basic installaon is completed, it
is ready for shoong. You can add other
accessories to this kit according to your
requirement.
Warranty: We oer one year warranty for our products from date of purchase. Within this period of me,
we will repair it without charge for labor or parts. Warranty doesn’t cover transportaon costs nor does it
cover a product subjected to misuse or accidental damage. Warranty repairs are subjected to inspecon
and evaluaon by us.
Liability: We are not liable for damage caused by products that we do not supply or from mishandling in
transit, accident, misuse, neglect, lack of care of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissasfacon, please Contact us immediately and we promise our
utmost support and care unl you use our product.