Fimer TRIO-5.8-TL-OUTD User manual

Product Manual
TRIO-5.8/7.5/8.5-TL-OUTD
(5.8 to 8.5 kW)

2
000314EG-F
IMPORTANT SAFETY INSTRUCTIONS
This manual contains important safety instructions that must be followed during installation
and maintenance of the equipment.
Operators are required to read this manual and scrupulously follow the indications reported
in it, since FIMER cannot be held responsible for damages caused to people and/or things,
or the equipment, if the warranty conditions are not observed.

3
000314EG-F
Product Manual
TRIO-5.8/7.5/8.5 string inverters
1 - Introduction and general information
2 - Characteristics
3 - Safety and accident prevention
4 - Lifting and transport
5 - Installation
6 - Instruments
7 - Operation
8 - Maintenance
FIMER-TRIO-5.8_7.5_8.5-TL-OUTD-Product manual EN Rev E (M000018EG)
EFFECTIVE 26/05/2021
© Copyright 2021 FIMER. All Rights Reserved.

4
000002EG-F
Warranty and Supply Conditions
The warranty conditions are considered to be valid if the customer adhe-
res to the indications in this manual; any conditions deviating from those
described herein must be expressly agreed in the purchase order.
The equipment complies with the pertinent legislation currently in force in the country of in-
stallation and it has issued the corresponding declaration of conformity.
Not included in the supply
FIMER accepts no liability for failure to comply with the instructions for correct installation and
will not be held responsible for systems upstream or downstream the equipment it has supplied.
It is absolutely forbidden to modify the equipment. Any modication, manipulation, or alteration
not expressly agreed with the manufacturer, concerning either hardware or software, shall re-
sult in the immediate cancellation of the warranty.
The Customer is fully liable for any modications made to the system.
Given the countless array of system congurations and installation envi-
ronments possible, it is essential to check the following: sufcient space
suitable for housing the equipment; airborne noise produced depending
on the environment; potential ammability hazards.
FIMER will NOT be held liable for defects or malfunctions arising from:
improper use of the equipment; deterioration resulting from transporta-
tion or particular environmental conditions; performing maintenance in-
correctly or not at all; tampering or unsafe repairs; use or installation by
unqualied persons.
FIMER will NOT be held responsible for the disposal of: displays, cables,
batteries, accumulators etc. The Customer shall therefore arrange for the
disposal of substances potentially harmful to the environment in accor-
dance with the legislation in force in the country of installation.
1
Introduction and general information

5
000315EG-F
1- Introduction and general information
Contents
Introduction and general information............................................................................................... 4
Warranty and Supply Conditions..........................................................................................................4
Not included in the supply.......................................................................................................4
Contents ..................................................................................................................................................5
Reference number index .......................................................................................................................8
Graphical representation of references...............................................................................................8
Scope and target audience....................................................................................................................9
Purpose and document structure ...........................................................................................9
List of appendix documents ....................................................................................................9
Operator and maintenance personnel skills/prerequisites .....................................................9
Symbols and signs...............................................................................................................................14
Field of use, general conditions ........................................................................................................11
Intended or allowed use........................................................................................................ 11
Limits in field of use............................................................................................................... 11
Improper or prohibited use ................................................................................................... 11
Characteristics .................................................................................................................................. 12
General conditions ...............................................................................................................................12
Models and range of equipment .........................................................................................................13
Identification of the equipment and the manufacturer ..........................................................14
Inverter Composition ...........................................................................................................................16
5.8kW Standard / -S Version ................................................................................................16
7.5kW and 8.5kW Standard / -S Version..............................................................................17
Accessory components (installable on the inverter) .......................................................................18
“Wifi Logger Card” accessory card .......................................................................................18
“ETHERNET Expansion Board” accessory board................................................................19
“PMU Expansion Board” accessory board ...........................................................................19
Characteristics and technical data.....................................................................................................20
Tightening torques ................................................................................................................22
Overall dimensions ...............................................................................................................22
Bracket dimensions...............................................................................................................23
Efficiency curves ..................................................................................................................................24
Power derating......................................................................................................................................25
Power derating due to environmental conditions .................................................................26
Power reduction due to the input voltage .............................................................................26
Characteristics of a photovoltaic generator......................................................................................27
Strings and Arrays.................................................................................................................27
Description of the equipment..............................................................................................................28
Operating diagram ................................................................................................................28
Connection of several inverters together..............................................................................29
Notes on the sizing of the system.........................................................................................29
Functionality and components of the equipment .................................................................30
Topographic diagram of the equipment ................................................................................32
Safety devices.......................................................................................................................................34
Anti-Islanding ........................................................................................................................34
Ground fault of the photovoltaic panels ................................................................................34
Other safety devices .............................................................................................................34
Safety and accident prevention ...................................................................................................... 35

6
000315EG-F
1- Introduction and general information
Safety information and instructions ..................................................................................................35
Hazardous areas and operations .......................................................................................................36
Environmental conditions and risks ......................................................................................36
Signs and Labels ..................................................................................................................36
Thermal hazard ....................................................................................................................37
Clothing and protective devices for staff...............................................................................37
Residual risks .......................................................................................................................................38
Table of residual risks ...........................................................................................................38
Lifting and transport......................................................................................................................... 39
General conditions ...............................................................................................................................39
Transport and handling .......................................................................................................39
Lifting.....................................................................................................................................39
Unpacking and checking ......................................................................................................39
Installation ......................................................................................................................................... 40
General conditions ..............................................................................................................................40
List of components supplied .................................................................................................41
Weight of the groups of device .............................................................................................42
Environmental checks...........................................................................................................43
Installations above 2000 metres...........................................................................................43
Installation position................................................................................................................44
Wall mounting .......................................................................................................................................45
Opening the front cover ......................................................................................................................46
Operations preparatory to PV generator connection.......................................................................47
Checking the correct polarity of the strings ..........................................................................47
Checking of leakage to ground of the photovoltaic generator..............................................47
Choice of differential protection downstream of the inverter ................................................47
Independent or parallel input channels configuration.....................................................................49
Channel configuration examples ..........................................................................................50
Independent channel configuration (default configuration) ..................................................51
Parallel channel configuration ..............................................................................................51
Input connection to PV generator (DC side) .....................................................................................53
Connection of inputs - Standard Models ..............................................................................53
Connection of inputs - Models with disconnect switch (-S) ..................................................54
Installation procedure for quick fit connectors ......................................................................56
Grid output connection (AC side).......................................................................................................58
Characteristics and sizing of the protective earthing cable ..................................................58
Load protection switch (AC disconnect switch) ....................................................................58
Characteristics and sizing of the line cable ..........................................................................59
Connection to terminal block AC side...................................................................................59
Installation of the second protective earthing cable .............................................................60
Communication and control board ....................................................................................................61
Connections to the communication and control board...................................................................62
Remote control connection ...................................................................................................62
Configurable Relay connection (ALARM).............................................................................63
Serial Connection Communication (RS485 PC) ..................................................................64
Monitoring and control systems ........................................................................................................65
Procedure for RS485 connection to a monitoring system....................................................65
Closing the front cover ........................................................................................................................66
Instruments........................................................................................................................................ 67
General conditions ..............................................................................................................................67

7
000315EG-F
1- Introduction and general information
Display and keyboard ..........................................................................................................................68
Display fields and symbols description.................................................................................68
Description of keyboard and LED Panel...............................................................................69
Operation ........................................................................................................................................... 70
General conditions ..............................................................................................................................70
Monitoring and data transmission .....................................................................................................71
User interface mode..............................................................................................................71
Types of data available .........................................................................................................71
Measurement tolerance ........................................................................................................71
Commissioning.....................................................................................................................................72
Display access and settings .................................................................................................75
Updating the firmware from an SD card ...............................................................................75
Dynamic display behaviour...................................................................................................76
LED behaviour ......................................................................................................................................77
Specifications on the operation of the LEDs.........................................................................78
LED insulation fault ...............................................................................................................78
Description of the menus ....................................................................................................................79
General information ..............................................................................................................79
Statistics Menu......................................................................................................................81
Settings Menu .......................................................................................................................83
Info Menu ..............................................................................................................................92
AUTOTEST procedure in accordance with standard CEI 0-21........................................................93
Running the tests from the display menu .............................................................................93
Inverter switch-off.................................................................................................................................95
Maintenance ...................................................................................................................................... 96
General conditions ..............................................................................................................................96
Routine maintenance............................................................................................................97
Troubleshooting ....................................................................................................................97
Alarm Messages ...................................................................................................................97
Power limitation messages .................................................................................................104
Putting the inverter out of service....................................................................................................106
Registration on “Registration” website and calculation of second-level password (Service
Menu) ...................................................................................................................................................107
Resetting the time remaining to change the grid standard...........................................................108
Replacement of the buffer battery....................................................................................................109
Verification of ground leakage .........................................................................................................110
Behaviour of a system without leakage .............................................................................. 110
Behaviour of a system with leakage ................................................................................... 111
Measuring the insulation resistance of photovoltaic generator................................................... 112
Storage and dismantling ..................................................................................................................113
Storage of the equipment or long period of non-use.......................................................... 113
Dismantling, decommissioning and disposal......................................................................113
Contact us ...........................................................................................................................................114

8
000315EG-F
1- Introduction and general information
TRIO-5.8-TL-OUTDTRIO-5.8-TL-OUTD-STRIO-7.5/8.5-TL-OUTDTRIO-7.5/8.5-TL-OUTD-S
I ON
0 OFF
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
01
02
03
04
05
06
07
08
09
10
11
12
13
14 1516
1516
17
18
1516
17
18
08
17 19 20
151608
17 19
01 , display
02 , LED panel
03 , keyboard
04 , front cover
05 , AC output board
06 , communication and control board
07 , DC input board
08 , DC disconnect switch
09 , bracket anchor hole
10 , inverter
11 , handles
12 , heat sink
13 , bracket
14 , locking screw
15 , AC cable gland
16 , service cable glands
17 , anti-condensation valve
18 , DC cable gland
19 , input connectors (MPPT1)
20 , input connectors (MPPT2)
Reference number index
Graphical representation of references

9
000004EG-F
1- Introduction and general information
Scope and target audience
Purpose and document structure
This operating and maintenance manual is a useful guide that will enable
you to work safely and carry out the operations necessary for keeping the
equipment in good working order.
If the equipment is used in a manner not specied in this manual, the protection provided by
the equipment may be impaired.
The language in which the document was originally written is ITALIAN; therefore, in the event of
inconsistencies or doubts please ask the manufacturer for the original document.
List of appendix documents
In addition to this operating and maintenance manual (if applicable or on
request), the following documentation is supplied:
- EC declaration of conformity
- Quick installation guide (QIG)
Part of the information given in this document is taken from the original supplier documents.
This document contains only the information considered necessary for the use and routine
maintenance of the equipment.
Operator and maintenance personnel skills/prerequisites
Personnel in charge of using and maintaining the equipment must be skilled for the described
tasks and must reliably demonstrate their capacity to correctly interpret what is described in
the manual.
For safety reasons, only a qualied electrician who has received training and/or demonstra-
ted skills and knowledge of the inverter’s structure and operation may install the inverter.
The installation must be performed by qualied installers and/or licensed electricians in ac-
cordance with the existing regulations in the country of installation.
Inverter operation and maintenance by a person who is NOT qualied, is intoxicated, or on
narcotics, is strictly forbidden.
The customer has civil liability for the qualication and mental or physical state of the person-
nel who interact with the equipment. They must always use the personal protective equipment
(PPE) required by the laws of the country of destination and whatever is provided by their
employer.

14
000006HG-F
1 - Introduction and general information
Symbols and signs
In the manual and/or in some cases on the equipment, the danger or
hazard zones are indicated with signs, labels, symbols or icons.
Symbol Description
Indicates that it is mandatory to consult the manual or original document,
which must be available for future use and must not be damaged in any
way.
General warning - Important safety information. Indicates operations or
situations in which staff must be very careful.
Dangerous Voltage - Indicates operations or situations in which staff
must be very careful with regard to dangerous voltage levels.
Hot parts - Indicates a risk arising from the presence of hot zones or
zones with parts at high temperatures (risk of burns).
Risk of explosion
Risk of injury due to the weight of the equipment. Take care during lifting
and transport
Indicates that the area in question must not be accessed or that the
operation described must not be carried out.
Keep out of the reach of children
Indicates that smoking and the use of naked ames is prohibited.
Indicates that it is mandatory to carry out the described operations
using theclothing and/or personal protective equipment provided by the
employer.
WEEE logo. Indicates that the product is to be disposed of according to
current legislation regarding the disposal of electronic components.
IPXX Indicates the protection rating of the equipment according to IEC 70-1
(EN 60529 June 1997) standard.
Point of connection for grounding protection.
Indicates the permitted temperature range

15
000006HG-F
1 - Introduction and general information
Symbol Description
XX
Risk of electric shock.The discharge time (quantied in the gure by the
number XX) of the stored energy after de-energizing of the Inverter from
both DC side and AC side.
Warning! Refer to the dedicated procedures in the Instruction Manual
before accessing to active parts inside the Inverter.
DC
Direct Current
AC
Alternate current
With isolation transformer
Without isolation transformer
Positive pole of the input voltage (DC)
Negative pole of the input voltage (DC)
Indicates the centre of gravity of the equipment.
Indicates the requirement to wear acoustic protection devices in order to
prevent damage to hearing

11
000007CG-F
1- Introduction and general information
Field of use, general conditions
FIMER shall not be liable for any damages whatsoever that may result
from incorrect or careless operations.
You may not use the equipment for a use that does not conform to that provided for in the
eld of use. The equipment MUST NOT be used by inexperienced staff, or even experienced
staff if carrying out operations on the equipment that fail to comply with the indications in this
manual and enclosed documentation.
Intended or allowed use
This equipment is a inverter designed for:
transforming a continuous electrical current (DC)
supplied by a photovoltaic generator (FV)
in an alternating electrical current (AC)
suitable for feeding into the public distribution grid.
Limits in field of use
The inverter can be used only with photovoltaic modules which have ground isolated input
poles, unless they are accessories installed that enable earthing of the inputs. In this case
you must install an insulating transformer on the AC side of the system.
Only a photovoltaic generator can be connected in the input of the inverter (do not connect
batteries or other sources of power supply).
The inverter can be connected to the electricity grid only in countries for which it has been
certied/approved.
The inverter cannot be connected to the DC side in parallel to other inverters to convert ener-
gy from a photovoltaic generator with a power greater than the nominal power of the single
inverter.
The inverter may only be used in compliance with all its technical characteristics.
Improper or prohibited use
IT IS STRICTLY FORBIDDEN TO:
• Install the equipment in environments subject to particular conditions of ammability or in
adverse or disallowed environmental conditions, (temperature and humidity).
• Use the equipment with safety devices which are faulty or disabled.
• Use the equipment or parts of the equipment by linking it to other machines or equipment,
unless expressly provided for.
• Modify operating parameters that are not accessible to the operator and/or parts of the
equipment to vary its performance or change its isolation.
• Clean with corrosive products that could eat into parts of the equipment or generate elec-
trostatic charges.
• Use or install the appliance or parts of it without having read and understood the contents of
the user and maintenance manual.
• Heat or dry rags and clothing on the parts in temperature. In addition to being hazardous,
doing so would compromise component ventilation and cooling.

12
000008EG-F
General conditions
A description of the equipment characteristics is provided to identify its
main components and specify the technical terminology used in the ma-
nual.
This chapter contains information about the models, details of the
equipment, characteristics and technical data, overall dimensions and
equipment identication.
The customer/Installer takes full responsibility if, when reading this manual, the chronological
order of its presentation provided is not observed. All information is provided considering
occasional inclusion of information in previous chapters.
In certain cases, there may be a need to separately document softwa-
re functionality or attach supplementary documentation to this manual
which is intended for more qualied professionals.
2
Characteristics

13
000316CG-F
2 - Characteristics
Models and range of equipment
The specic models of three-phase inverters covered by this manual are
divided into three groups according to their maximum output power:
5.8 kW, 7.5kW or 8.5 kW.
For inverters of equal output power the variant between the various mo-
dels is the presence or lack thereof of the DC disconnect switch 08
The choice of the inverter model must be made by a qualied technician who knows about
the installation conditions, the devices that will be installed outside the inverter and possible
integration with an existing system.
• TRIO-5.8-TL-OUTD MODELS
I ON
0 OFF
TRIO-5.8-TL-OUTD-400:
• Number of input channels: 1
• DC disconnect switch 08 : No
• Input connectors: screw terminal block
I ON
0 OFF
TRIO-5.8-TL-OUTD-S-400:
• Number of input channels: 1
• DC disconnect switch 08 : Yes
• Input connectors: quick t connectors (2 pairs)
• TRIO-7.5-TL-OUTD MODELS
TRIO-7.5-TL-OUTD-400:
• Number of input channels: 2
• DC disconnect switch 08 : No
• Input connectors: screw terminal block
TRIO-7.5-TL-OUTD-S-400:
• Number of input channels: 2
• DC disconnect switch 08 : Yes
• Input connectors: quick t connectors (2 pairs for each channel)
• TRIO-8.5-TL-OUTD MODELS
TRIO-8.5-TL-OUTD-400:
• Number of input channels: 2
• DC disconnect switch 08 : No
• Input connectors: screw terminal block
TRIO-8.5-TL-OUTD-S-400
• Number of input channels: 2
• DC disconnect switch 08 : Yes
• Input connectors: quick t connectors (2 pairs for each channel)

14
000316CG-F
2 - Characteristics
N.B. The labels must NOT be hidden with objects and extraneous parts (rags, boxes,
equipment, etc.); they must be cleaned regularly and kept visible at all times.
Identification of the equipment and the manufacturer
The technical data shown in this manual do not in any case replace those
shown on the labels attached to the equipment.
The labels attached to the equipment must NOT be removed, damaged, dirtied, hidden, etc.
The approval label contains the following information:
1. Manufacturer
2. Model
3. Rating data
4. Certication marks
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
14
2
3
V dc max
V dc Operating Range
V acr
f r
I ac max
P acr (cos = ±0.9) φ
P acr (cos = 1) φ
MODEL:
TRIO-X.X-TL-OUTD-400
Made in Italy
DIN VDEV 0126-1-1
PROTECTIVE CLASS: I
SOLAR INVERTER
V dc MPP
I dc max
I sc max
IP65
-25 to +60 °C
-13 to +140 °F
10 minutes

15
000316CG-F
2 - Characteristics
In addition to the label showing the specications of the inverter, there
are two part identication labels for the inverter and wiring box.
These labels list the following information:
The ofcially required information is located on the approval label. The identication label
is an accessory label which shows the information necessary for the identication and cha-
racterisation of the inverter by FIMER.
N.B. The labels must NOT be hidden with objects and extraneous parts (rags, boxes, equip-
ment, etc.); they must be cleaned regularly and kept visible at all times.
P/N:PPPPPPPPPPP
WO:XXXXXXX
SO:SXXXXXXXX Q1
SN:YYWWSSSSSS WK:WWYY
TRIO-X-TL-OUTD-Y-400
ABB
• Inverter model
- X.X = Inverter power rating:
- Y = Integrated disconnect switch
• Inverter Part Number
• Inverter Serial Number composed of:
- YY = Year of manufacture
- WW = Week of manufacture
- SSSSSS = sequential number
• Week/Year of manufacture

16
000317CG-F
2 - Characteristics
Inverter Composition
For each power size of the inverter 10 (5.8 / 7.5 / 8.5kW) 2 versions are
available with different set-ups.
5.8kW Standard / -S Version
TRIO-5.8-TL-OUTD: Standard inverter version
TRIO-5.8-TL-OUTD-S: -S inverter version, as standard version but with
DC disconnect switch 08
Table: TRIO-5.8kW main inverter components
Ref.
Inverter
Ref.
manual. Description
-AC output board
-communication and control board
-07 DC input board
-DC disconnect switch
J1-J2 input varistors
J3 23 DC input terminal block
J14 24 SLOT 3 - Connector for WIFI modules installation (NOT ACTIVE)
A1 25 SD CARD housing
J2 26 Connection to the multi-function relay
J9 27 SLOT 1 - Connector for Radio module or Ethernet card installation
J3 28 SLOT 2 - Connector for PMU card installation
J4 29 Connection of the RS485 (PC) line, remote ON/OFF and Tachometer
signal (WIND version)
J7-J11 30 RS485 (PC) line connection on RJ45 connector
J1 31 AC output terminal block
J7-J8-J9-J10 32 AC output varistors
05
06
08
21
Standard Version
1
R S T N G
21
07
23
24 25
32
05
31
27 28 29 30 0626
-S Version
1
R S T N G
21
07
08
24 25
32
05
31
27 28 29 30 0626

17
000317CG-F
2 - Characteristics
7.5kW and 8.5kW Standard / -S Version
TRIO-7.5-TL-OUTD / TRIO-8.5-TL-OUTD: Standard inverter version
TRIO-7.5-TL-OUTD-S / TRIO-8.5-TL-OUTD-S: -S inverter version, as
standard version but with DC disconnect switch 08
Table: TRIO-7.5 / 8.5kW main inverter components
Ref.
Inverter
Ref.
manual. Description
-05 AC output board
-06 communication and control board
-07 DC input board
-08 DC disconnect switch
J1-J2-J8-J10 input varistors
TB1-TB8
TB15-TB19
22 Terminals for installation of jumpers for parallel input channels
J3-J5 DC input terminal block
J14 SLOT 3 - Connector for WIFI modules installation (NOT ACTIVE)
A1 25 SD CARD housing
J2 26 Connection to the multi-function relay
J9 27 SLOT 1 - Connector for radio module or Ethernet card installation
J3 28 SLOT 2 - Connector for PMU card installation
J4 29 Connection of the RS485 (PC) line, remote ON/OFF and Tachometer
signal (WIND version)
J7-J11 Connection of the RS485 (PC) line on RJ45 connector
J1 AC output terminal block
J7-J8-J9-J10 AC output varistors
21
23
24
30
31
32
Standard Version
1
R S T N G
21
07
23
22
25
32
24
05
31
27 28 29 30 0626
-S Version
1
R S T N G
21
07
08
22
25
32
24
05
31
27 28 29 30 0626

18
000317CG-F
2 - Characteristics
Accessory components (installable on the inverter)
For all inverter models accessory components are available that add
specic functions to the inverter.
The accessories can be bought separately and installed directly by a qualied technician or
by the installer.
The main characteristics of the accessory components are listed in the
following paragraphs.
For information on the installation, compatibility and use, refer to the relevant accessory com-
ponent documentation.
“Wifi Logger Card” accessory card
The Wi Logger Card is a useful accessory for adding a wireless com-
munication line (WiFi) for connecting the inverter with a WLAN local
network permitting data transmission to the Aurora Vision Plant Viewer/
Aurora Vision®web portal for remote monitoring of the inverter/system
via an internet or mobile browser App (Aurora Vision Plant Viewer for Mobile)
The code to use when ordering the accessory is: VSN300 Wi Logger Card
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
J1
U8
U3
U11
U7
J2
1
2
23
24
Aurora Vision
Plant Viewer
WI-FI router
INTERNET
Aurora Vision
Aurora Vision Plant Viewer™
web platform
®
for Mobile
The accessory is made up of three components:
- Scheda WiFi
- Antenna
- Cable for connection between WiFi card and antenna
The Wi Logger Card is installed in the inverter on the connector referred
to as SLOT 1 27 on communication and control card 06 .
The Wi Logger Card is in turn connected with a wire ending in an adap-
ter to be installed in place of one of the service cable glands 16 (on the
outside of the inverter) with a connector on which to install the antenna.
Installation of the Wi Logger Card makes it impossible to use the “ETHERNET expansion
board” accessory as both use the same connector on the inverter
J1
U8
U3
U11
U7
J2
1
2
23
24

19
000317CG-F
2 - Characteristics
“ETHERNET Expansion Board” accessory board
The Ethernet board is an accessory that allows you the possibility of con-
necting to the LAN for inverter monitoring; this may be done locally, with
direct connection to the PC, by accessing the internal web server; or
remotely, with internet connection to the through a router, to the portal
"Aurora Vision Plant Viewer/Aurora Vision®".
The code to use when ordering the accessory is: ETHERNET Expan-
sion Board
Router
ABB
“Aurora Vision”
“AV Plant Viewer”
ABB
“Aurora Vision”
“AV Plant Viewer”
ABB
“Aurora Vision”
“AV Plant Viewer”
Ethernet
Ethernet
Ethernet
ABB
local web
server
Ethernet
Wi-Fi
or
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
TRIO
POWER ALARM GFI ESC UP DOWN ENTER
INTERNET
Install the Ethernet board to the interior of the inverter (to the connector
named SLOT 1 27 which can be found on the communication and control
board 06 ).
Installing the "ETHERNET Expansion Board" makes it impossible to use the " VSN300 Wi
Logger Card" accessory because both use the same wiring connector on the inverter.
“PMU Expansion Board” accessory board
The PMU board is an accessory which allows you to add additional fun-
ctionality to the inverter:
• PMU - Ability to remotely control reactive power and active power limi-
tation by the grid or system manager.
• Analogue inputs - Allows you to connect up to 4 analogue sensors (AN1,
AN2, AN3, AN4) and a PT100 or PT1000 sensor.
Inputs AN3 and AN4 can be used to control the PMU functions. In
this case the number of environmental sensors which can be con-
nected is 2 (AN1 and AN2)
• Analogue sensors power supply (16Vdc)
• RS485 serial line communication which can be used with a ModBus
RTU communication protocol.
The code to use when ordering the accessory is: PMU expansion board
Install the PMU board to the interior of the inverter (to the connector na-
med SLOT 2 28 which can be found on the communication and control
board 06 ).
LAB1
J6
16
15
2
1
R28
U2
U1
R29
R30
R31
D3
D2
U4
R2
R1
C1
R32
R33
R34
R22
R23
C12
U5
R5
R4
R3
Q1
D4 R24
C11
U6
R7
R6
C21
R35 L2
L1
U7
R8
R36
R37
R27
R26
R25
C13
U8
R10
R9
D6
R39
L3
C14
LED1
R12
R11
R13
C43
C44
R58
C31
R52
C29
C26
C23
D7
R67
R68
R21
LED2
LED3
R16
C5
C2
R59
C45
U11
D5
C24
C27
XTAL2
C15
C9
C7
U3
R60 C36
C37
L4
R38
LAB1
R56
R53
R48
R51
R54
C6
C3
C30
C25
XTAL3
R47
R44
R45
C8
R20
R18
R19
R15
R17
C4
C34
C38
C10
U10
C39
R49
R46C28
C35
U12
U9
D1
R14
C19
C40
R57
C32
C48 R61
R55C41
C47
C20
R62
R63
R65
R64
R66
C33
L5
C22
R40
R41
LED4
LED5
TP5
TP14
TP22 TP24
TP23
TP13
TP3
TP12
TP6
TP4
J3
TP7
TP25
TP2
J1
TP21
TP18
TP17
TP20
J2
28
7
17
23
24
AC
1
1
2