Fire-Lite MS-9200 Installation and operating instructions

Document50053 RevM 1/10/08 P/N50053:M 1 of 5
MS-9200(C)/E
Field Software Change Procedure
(and Programming Existing MS-9200
Systems for use with the LCD-40)
Document #50053 Rev. M 1/10/08
ECN 08-019 P/N 50053:M
Firmware Change
This procedure outlines the mechanical installation steps required to install EPROMs in the MS-9200, MS-9200C
andMS-9200E.
Handling precautions for integrated circuits
Static electricity can destroy integrated circuits (ICs)! To prevent damage to the EPROM, a wrist strap and a
static-freeICinsertion/extractiontoolishighlyrecommended.Themanufacturercannotberesponsiblefor
damage to the EPROM as a result of improper handling.
System Power Sources
Always remove primary and secondary power before working on the system!
1. Disconnectbattery backuppowerbefore workingon thesystem!
2. Proceed by disconnecting AC power to the panel at the main service circuit
breaker(notthecircuitbreaker at the alarm control panel's power supply).
3. Wait 60 seconds to allow for capacitive discharge before touching any of the
system's components.
4. Reversetheprocedure for powering up the system - ACfirst- then batteries.
Pin 1
Notch
Integrated Circuit Pin Conversion
ObserveproperorientationofanyICremovedorinstalled!NotelocationofPin1withrespecttothenotchinthe
bodyoftheIC.ThereplacementEPROMmustbeinstalledinthesamemannerastheEPROMremoved.Failure
toobservethisorientationwillresultindestructionoftheEPROM.NOTE:SomeICsmayhaveasmalldotinstead
of a notch for orientation purposes.

2 of 5 Document50053 RevM 1/10/08 P/N50053:M
EPROM Replacement
ObserveproperorientationofanyICremovedorinstalled!ToreplacetheEPROM,completethefollowingsteps:
1.MakecertainSoftware RevisionandCircuitBoardRevisionarecompatible(refertotableonpage4).
2.Once allpower hasbeenremoved, disconnectanyoptional modules(if installed).
3.LocateEPROMU16 onnewer boardsor U14onolder boards(center rightof theboard).
4.Gentlyloosenand removeEPROMfromtheboard.
5.InstallreplacementEPROM.Observeproperorientation!ThenotchordotontheIC
should be positioned to the left for U16 in the newer boards or to the right for U14 in older boards as
shown below. Use care to insure that the EPROM's pins are not bent or broken during insertion.
6. Reconnectpowersupplies.
Programming and Testing
ReprogramandtesttheMS-9200(C)/EafterEPROMreplacement.
EPROM(U16)
(newerboards)
EPROM(U14)
(olderboards)
CircuitBoardassembly
information(Rev.)canbe
foundintheupperright
corner of the circuit board.
U16
U14
Rev._
CircuitBoardassembly
information(Rev.)canbe
foundintheupperright
cornerofthecircuitboard.
Rev._

Document50053 RevM 1/10/08 P/N50053:M 3 of 5
LCD-40 installation in an existing MS-9200(C)/E
InanexistingMS-9200(C)/Einstallation,thefollowingproceduremustbefollowedtoprogramtheMS-9200(C)/Efor
usewiththeLCD-40SeriesAnnunciator:
1. ConnecttheLCD-40totheMS-9200(C)/EControlPanel(refertotheappropriateMS-9200(C)/ETechnical
ManualandProductInstallationDrawings).
2. Software Versions:
(1)IfsoftwarewitheitherthePartNumber73750or73829isinstalledintheMS-9200(C),theLCD-40
SeriesAnnunciatormusthavesoftwarewithaPartNumberof73779or73879tooperatewiththe
FACP(FireAlarmControlPanel). IfsoftwarewithaPartNumberof#M9200V20orhigherisinstalled
in the MS-9200(C), the LCD-40 Series Annunciator must have software with a Part Number of
#LCD40V20orhighertooperatewiththeFACP.
(2)IfsoftwarewithPartNumber73846isinstalledintheMS-9200E,theLCD-40SeriesAnnunciator
musthavesoftwarewithPartNumber73779or73879tooperatewiththeFACP. Ifsoftwarewith
PartNumber#M9200EV20orhigherisinstalledintheMS-9200E,theLCD-40SeriesAnnunciator
musthavesoftwarewithaPartNumber of#LCD40V20 orhigher tooperate withtheFACP.
3. Uponinitialpower-upoftheMS-9200(C)/Ewiththenewsoftwareinstalled,thefollowingmessagemay
appearontheMS-9200(C)/ELCDdisplay:
"TROUBLEINSYSTEM
PROGRAMCORRUPTED"
Whether the above message appears or not, the following steps must be followed to program the
MS-9200forusewiththeLCD-40.
4. Press the ENTER key.
5. Press the 1 key to select Programming.
6. Enter your LEVEL 1 password.
7. Press the ENTER key.
8. Press the 1 key to select Autoprogram.
9. Upon successful completion of the Autoprogram function, press the LEFT ARROW key.
10. Press the 3 key to select System Edit.
11. At this point, use the RIGHT ARROW key to select TRM = N (or L/P = N as shown in the manual).
12. Press the UP ARROW key to change 'N' to'L' in order to program the system for LCD-40 use.
13. Be sure to press the ENTER key to store the programming change in memory.
14. Press the LEFT ARROW key several times to get back to the SYSTEMS ALL NORMAL display.
15.Atthispoint,theMS-9200(C)/EshouldbesuccessfullyprogrammedforusewiththeLCD-40. Toensure
thatallprogrammingchangeshavebeenaccepted,depresstheRESETkey. Thesystemshouldreturn
to the SYSTEMS ALL NORMAL display, after a successful software check.

4 of 5 Document50053 RevM 1/10/08 P/N50053:M
Software Changes
The following Table summarizes the MS-9200(C) software changes, specifying these changes by EPROM
NumberandReleaseNumber.
#MORP#esaeleRsegnahCfoyrammuS
294370.1esaeleRlaitinI
425371.1 tluafedyrotcafehtotsdrowssap2leveLro/dna1leveLs
nruterhcihwnoitcnuFraelCdrowssaPddA .llirdagnirudstiucricecnailppanoitacifitonhtobnonrutoterutaefllirD
eriFegnahC.sgnittes .noitacifitnedielbuortecivedcificepsddA
465372.1 gnisusecivedroecivedafolavomerehtswo
llahcihwnoitcnuFeteleDecivedehtstcerroC .gnimmargorpecivedgniniamerehtfonoitaretlatuohtiw,edommargorpo
tuA
085373.1 .edom)rettimsnarT/rotacinummoCmralAlatigiDlasrevinU(TCADUddA
106374.1 dneS.edoMTCADUninehwelbu
orTrotaicnunnAfodaetsnielbuorTTCADUottroperretnirpegnahC nehwTCADUotelbuorTlareneGdnestonlliW.sruccoel
buortyrettabnehwTCADUotelbuorTlareneG .sruccoliafCA
057370.veR .ylnOesaeleRateB.deddasllebhtobfognimmargo
rP.deddatroppus04-DCL
057371.veR .ylnOesaeleRateB.ecafretnilairesnoytirapdnamuskcehcddasegnahC
057375.1 .2&
1sllebelbammargorpdnatroppus04-DCLfoesaelergnirutcafunaM
928376.1 .stiucric)lleb(CANfognicnuobedstcerroC
.gnitroperrorrednagnikcehcMORPEsetavitcA
02V0029M#0.2 .noitcetorpatad04-DCLsevorpmI.noitasnepmocraeypael
sddA'.yrosivrepuselbatteser-otua'sddA
12V0029M#1.2 .gnidaerretemtlovCAevomeR.tuotnirp)atadrotceted(ytivi
tisnessddA
22V0029M#2.2 tibihnIecneliSgnirudnottubteseRelbasiD.sdnoces06otnoitamrifnoCnoitacifireVmralAe
gnahC nottubecneliSfiegassemyalpsiD.smralatneuqesbushtiwdetratsertonsiremiTtibihnIecneliS.emit .tibihnI
ecneliSgniruddesserpsi
draobtiucricynanidesuebnacerawtfosreilraedna2.2noisiveR .noisiverylbmessa
32V0029M#3.2.rossecorporcimwenrofetadpU
ylbmessadraobtiucricnidesuebylnonacerawtfos3.2noisiveR .retalroFnoisiveR
52V0029M#5.2 snepoCLSfismelborpgnisuacsecivedCISAdesaelerylwenhtiwmelborp7/6elytSCLSnatcerroC .pu

Document50053 RevM 1/10/08 P/N50053:M 5 of 5
Software Changes
The following Table summarizes the MS-9200E software changes, specifying these changes by EPROM
NumberandReleaseNumber.
#MORP#esaeleRsegnahCfoyrammuS
648370.1esaeleRlaitinI
02VE0029M#0.2 .noitcetorpatad04-DCLsevorpmI.noitasnepmoc
raeypaelsddA'.yrosivrepuselbatteser-otua'sddA
12V0029M#1.2 .gnidaerretemtlovCAevomeR.tuotnirp)atadrotcet
ed(ytivitisnessddA
22V0029M#2.2
tibihnIecneliSgnirudnottubteseRelbasiD.sdnoces06otnoitamrifnoCnoitacifir
eVmralAegnahC ecneliSfiegassemyalpsiD.smralatneuqesbushtiwdetratsertonsiremiTtibihnIecneliS.emit .tibih
nIecneliSgniruddesserpsinottub
draobtiucricynanidesuebnacerawtfosreilraedna2.2noisiveR .noisiverylbmessa
32V0029M#3.2
.rossecorporcimwenrofetadpU
ylbmessadraobtiucricnidesuebylnonacerawtfos3.2noisiveR .retalroFnoisiveR
52V0029M#5.2 snepoCLSfismelborpgnisuacsecivedCISAdesaelerylwenhtiwmelborp7/6elytSCLSnatcerroC .pu