FireMagic Aurora User manual

Outdoor Stand Alone
Gas Grill
Quick Start Guide
INSTALLER: Leave these instructions with consumer. CONSUMER: Retain for future reference.
CAUTION: For your safety read the installation instructions and owner’s manual provided with the grill.
This grill must be installed in accordance with local codes and ordinances, or, in the absence of local codes, with either the latest National Fuel Gas Code (ANSI
Z223.1/NFPA 54), and Natural Gas and Propane Storage and Handling Installation Code (CSA-B149.1).
This appliance and its individual shutoff valves must be disconnected from the gas-supply piping system when testing the system at pressures in excess of ½ psig.
This appliance must be isolated from the gas-supply piping system by closing its dedicated manual shutoff valve during any pressure testing of the gas-supply
system at pressures up to and including ½ psig.
This grill is designed for outdoor use only. DO NOT use this grill under unprotected flammable surfaces. DO NOT use this grill inside a building, garage,
enclosed area, or an unprotected covered area (see paragraph below). DO NOT use this grill in or on a recreational vehicle or boat.
If installed or used under a patio roof, the cooking grid area must be fully covered by an exhaust hood with a vent. An exhaust fan with a rating of 1,000 CFM (cubic feet
per minute) (472 liters per second) or more may be necessary to effectively remove smoke and other cooking by-products from the area under the hood. Fire Magic Vent
Hoods are available to meet this requirement. This outdoor grill must not be used under overhead unprotected combustible construction. THIS UNIT MUST NOT BE
LOCATED IN A FULLY ENCLOSED AREA OF ANY KIND.
2-Unpacking
Carefully unpack the grill, removing all packing material and protective film.Verify that all
parts have arrived undamaged by consulting the parts list in the owner’s manual. Remove
foam packed hardware from oven area. (See Fig. 2-1.)
Consult the parts list in the owner’s manual. If any parts are missing or damaged,
immediately contact the Fire Magic dealer before beginning installation.
Fig. 2-1
1-Safety
Lift out foam packed hardware
Remove plastic
zip-ties
3-Installation
Location
Locate the grill on a flat level surface with 18” clearance from the oven back
and sides to any combustible material or construction.
CAUTION: Wind blowing into or across the rear oven lid vent (Fig.
3-1) can cause poor performance and/or dangerous
overheating. Orient the grill so that the prevailing wind
blows toward the front of the grill (Fig. 3-2).
CAUTION: To prevent dangerous overheating, the rear of the unit must have
a minimum clearance of 4” (10.2 cm) from any backsplash/wall.
Fig. 3-2
CORRECT
PLACE GRILL SO PREVAILING WIND
BLOWS TOWARD FRONT OF GRILL
YOU MUST PROTECT REAR OVEN
VENT FROM PREVAILING WIND
Rear oven lid vent
INCORRECT
Fig. 3-1
ReRearar oovevenn lilidd veventnt
Ventilation diagram
Fig. 3-5
To connect the regulator/
hose assembly to the
propane-gas cylinder valve
fitting: Press the hand nut
on the regulator over the
Acme thread fitting on the
cylinder valve. Turn the hand
nut clockwise to engage the
threads and tighten until
snug.
UL
Fig. 3-4 Type I Acme thread quick coupler
Vent
QCC
Type 1
valve
Brass Acme
thread fitting
Liquid level
indicator
(optional)
Hand nut with
Acme thread
Regulator
Hose
Hand wheel
Pressure
relief
valve
Connect Gas supply
These quick start instructions assume a
propane cylinder configured unit. See main
instructions for natural gas or household
propane configured units.
Place approved propane 20lb cylinder in tank
tray and lock holder in position (Fig. 3-3).
Connect quick coupler hose and regulator
supplied with unit to propane cylinder (Fig.
3-4).
Set all burner control valves to OFF and
open gas source control valve.
Follow the lighting instructions on the
reverse side of this guide.
Proper grill airflow must be maintained as
shown in Fig. 3-5.
Fig. 3-3
Quick
coupler
Propane
cylinder (tank)
Sideburner
shelf (if
equipped)
Tool holder Paper towel
holder
Backburner
cover (if
equipped)
Tank tray latch
REV 6 - 1311020955 L-C2-291

4-Grill Setup
Parts Placement Checklist
Place the following items according to their position and orientation in
Fig. 4-1:
Flavor grids, cooking grids, backburner cover, warming rack, meat probe.
Leave pre-installed E-burners in place to maintain proper alignment.
Backburner Cover (if equipped)
Hook the backburner cover over the top of the backburner to protect the
backburner from grease, dust and dirt when it is not in use.
Warming Rack
The warming rack comes pre-installed. Remove zip ties before use.
Consult the owner’s manual to remove or replace.
Shelf/Sideburner (if equipped)
Align the four (4) holes in the shelf with the four (4) holes in the side of
the cart while aligning and engaging the burner venturi with the orifice
(Fig. 4-2). Insert the four (4) screw (provided) into the holes and tighten.
Connect the spark wire to ignitor electrode (Fig. 4-2). Open sideburner
lid, set cap on burner, and set grid into shelf.
Screws
Ignitor
electrode
Air shutter
Orifice
Spark wire Fig. 4-2
Venturi
Center main burner control knob
(A540s and larger only)
Fig. 5-2
Left
main burner
control knob
Right main burner
control knob
Backburner
control knob
(if equipped)
Digital
thermometer Meat probe
Sideburner
control knob
(if equipped)
Drip tray
Fig. 4-1
Cooking Grid
Flavor Grid
(not with IR)
Backburner
cover
Warming
rack
Cotter
Pin
Rotisserie
rod storage
ring
Sideburner
lid
Note: For infrared burner equipped
grills; see detailed instructions
included in your owners manual.
Meat probe
Drip tray
liners
Drip tray (with
lighting instructions)
Fig. 5-1 - Valve control knob
OFF
HI
LIGHT
LOW
TO TURN OFF
T O TURN ON
Read setting
here
HIGH to
LIGHT
Read setting
here
To Turn OFF
To Turn ON
High to
light
6-Propane Safety
Gas Cylinders
IMPORTANT: READ AND FOLLOW ALL WARNINGS PROVIDED WITH THE PROPANE-GAS CYLINDER.
READ ALL SAFETY INSTRUCTIONS AND WARNINGS REGARDING THE USE OF PROPANE GAS FOUND IN
YOUR OWNERS MANUAL.
5-Test
1. Open the lid and remove any cover(s) of the burner(s) to be lit. (Ensure grill connected
to power.)
2. Turn all gas control knobs to the OFF position.
3. Turn the gas-supply valve on.
4. Depress the desired control knob, and while pressing turn it counterclockwise to the HI
LIGHT position. Once the burner lights, release the control knob. (Repeat this step for
each additional burner.)
CAUTION: If burner does not light within 5 seconds, IMMEDIATELY depress the knob and
turn it to the OFF position. Wait 5 minutes before repeating step 4. If the burner
does not light after repeated attempts, refer to the Lighting Instructions in your
Owners Manual.
WHEN OPERATING THIS
APPLIANCE WITH PROPANE,
ALL INSTRUCTIONS AND
WARNINGS MUST BE
OBSERVED. FAILURE TO DO
SO MAY RESULT IN A FIRE
OR EXPLOSION CAUSING
SERIOUS INJURY OR DEATH. Light
switch
Light
switch
REV 6 - 1311020955 L-C2-291
E-burner*
(pre-installed)
*The burner ports
and carry-over slots
must be kept clean to
ensure proper ignition
and operation.