Fisher & Paykel AS/NZS 60335-1 User manual

Installation instructions
• Read these instructions carefully before installing or using this product.
• Please make this information available to the person responsible for installing the product as it
could reduce your installation costs.
• In order to avoid a hazard, this appliance must be installed according to these instructions for
installation.
This cooktop has been designed and constructed in accordance with the following codes and specifications:
AS/NZS 60335-1 General Requirements for Domestic electrical appliances
AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances
AS/NZS 1044 Electromagnetic Compatibility Requirements.
Product dimensions and clearances
The installation shall comply with the dimensions in Figs. 1 and 2, bearing in mind the following requirements:
• A minimum clearance of 40 mm for CE302 models and 30 mm for CE604 models has to be kept between the
bottom of the cooktop and the top of an underbench appliance or a thermal protection barrier (see Figs. 5-7).
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
1

• Overhead clearances - In no case shall the clearance between the highest part of the cooktop and a range hood
be less than 600 mm. Any other downward-facing combustible surface less than 600 mm above the highest part
of the cooktop shall be protected for the full width and depth of the cooking surface area in accordance with local
regulations in force. However, in no case shall this clearance to any surface be less than 450 mm.
• Side clearances - Where the distance from the periphery of the nearest hotplate to any vertical combustible
surface is less than 50 mm (CE302 models) or 100 mm (CE604 models), the surface shall be protected in
accordance with with local regulations in force to a height of not less than 150 mm above the cooktop for the full
dimension (width or depth) of the cooking surface area.
One side of the cooktop must always be kept clear.
• Protection of combustible surfaces - The required protection shall ensure that the surface temperature of
combustible surfaces does not exceed 50 °C above ambient.
• To comply with this requirement satisfactorily, fix 5mm-thick ceramic tiles to the surface or attach fire-resistant
material to the surface and cover with sheet metal (minimum thickness 0.4 mm).
The underside surface of the cooktop can reach a temperature exceeding 95 °C during
normal use.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
2

Fig. 1 CE302 models clearances
Fig. 2 CE604 models clearances
Fig. 3 CE302 models product and cutout dimensions
Fig. 4 CE604 models product and cutout dimensions
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
3

Installing a thermal protection barrier
If the cooktop is installed over drawers or cupboards and its underside surface thus
becomes accessible after installation, a thermal protection barrier must be fitted at least 40
mm (for CE302 models) or 30 mm (for CE604 models) beneath the base of the cooktop
(see Figs. 5 and 6). This barrier must be made of low thermal conductivity material installed
according to the instructions for installation.
• The requirement above is not applicable if the cooktop is installed directly above an oven.
• For access to the cooktop for servicing or installation, ensure that the barrier can be removed
from beneath.
• A gap of 20 mm may be allowed at the rear of the barrier (see Fig.7) for electrical connection
and ventilation.
Fastening the installation brackets
• Each cooktop is provided with an installation kit including brackets and screws for fastening the cooktop to
benches from 20 to 40 mm thick.
• CE302 models are provided with four F type brackets.
• CE604 models are provided with two R type brackets (for the rear of the cooktop) and two F type brackets (for
the front of the cooktop).
1. Create a cutout according to the dimensions in Fig.3 or Fig.4.
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
4

2. Stretch gasket “D” (Figs. 10 and 11) over the edge of the cutout, being careful to overlay the junction edges.
3. Turn the cooktop upside down, place it on a soft surface and fasten the brackets F and R to the appropriate
socket holes, without tightening the screws B for the moment. Make sure that the tabs are mounted correctly,
as shown. Rotate the tabs so that the cooktop can be put into the cutout.
4. Put the cooktop into the cutout and position it correctly.
5. Put the brackets F and R into place; tooth A of the brackets should go into the hole (Figs. 10 and 11).
6. Tighten screws B until the cooktop is completely secured to the bench.
7. Using a sharp cutter or trimmer knife, trim the excess sealing material around the edge of the cooktop. Take
care not to damage the workbench.
Fig. 8 CE302 models
Fig. 9 CE604 models
Fig. 10 CE604 models rear side
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
5

Fig. 11 CE302 models front and rear side CE604 models
front side
Electrical requirements
• The appliance must be connected to the mains electricity supply checking that the voltage corresponds to the
value given in the rating plate and that the power supply cable sections can withstand the load specified on the
plate.
• Power supply cable and plug are NOT supplied with the appliance. A suitable cable has to be connected as
shown in Figs. 12 - 14 (CE302 models) or Figs. 15-17 (CE604 models).
• A suitable disconnection switch must be incorporated in the permanent wiring, mounted and positioned to
comply with the local wiring rules and regulations. The switch must be of an approved type installed in the fixed
wiring and provide a 3 mm air gap contact separation in all poles in accordance with the local wiring rules.
• In Australia and New Zealand, a switch of the approved type with a 3 mm air gap must be installed in the active
(phase) conductor of the fixed wiring.
• CE302 models only: It is possible to fit a standard 15 A plug suitable for the power drawn by
• the appliance. The plug must be connected to an earthed socket in compliance with safety standards.
• CE604 models only: due to the rating of the appliance, it is NOT possible to use a standard plug. The cooktop
must be connected to the electrical system by using fixed wiring.
• The power supply cable must not touch any hot parts and must be positioned so that it does not exceed 50°C
above ambient.
• Once the appliance has been installed, the switch or socket must always be accessible.
• If the power supply cable is damaged, it must only be replaced by the manufacturer or its Service Agent or a
similarly qualified person in order to avoid a hazard.
• This appliance must be earthed.
• If the installation requires alterations to the domestic electrical system call a qualified electrician. The electrician
should also check that the socket cable section is suitable for the power drawn by the appliance.
Connecting the power supply cable - CE302 models
1. Turn the cooktop over, place it on a soft surface, and unhook the terminal block cover by inserting a
screwdriver into the two hooks A (Fig. 12).
2. Open the cable clamp by unscrewing screw F (Fig. 14) and unscrew the terminal screws.
3. Connect mains and earth wires to their respective terminals in accordance with the connection diagram
(Fig.13).
4. Tighten the power supply cable, and fix it with clamp F.
5. Replace the terminal block cover correctly, keeping the power supply cable tight.
Use H05RR-F cables or equivalent rated minimum V-90.
• 230-240 V~ 3000-3300 W 50 Hz
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
6

Fig. 12 Unhooking the terminal block cover
Fig. 13 Connection diagram
Fig. 14 Fixing the power supply cable
Connecting the power supply cable - CE604 models
1. Turn the cooktop over and place it on a soft surface.
2. Unhook the terminal board cover by inserting a screwdriver into the two hooks C (fig. 15).
3. Unscrew the screw D and open completely the cable clamp E (fig. 17).
4. Check the bridging links F are inserted into terminal block A as shown (Figs. 16 - 17).
5. Connect the phase, neutral and earth wires to terminal board A according to the diagrams in figs. 16 - 17.
6. Strain the feeder cable and block it with cable clamp E (by screwing screw D).
7. Close the terminal block cover (check the two hooks C are correctly hooked).
To connect the power supply cable DO NOT unscrew the screws fixing the cover plate B
behind the terminal block.
Power supply special cable section type “H05V2V2-F” or equivalent rated minimum V-90.
Resistance to temperatures of 90°C
• 230-240 V~ 6000-6500 W 50 Hz (27A)
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
7

Fig. 15 Connecting the power supply cable
Fig. 16 Connection diagram
Fig. 17 Bridging links
Wiring diagram - CE302 models
Fig. 18 CE302 wiring diagram
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
8

Key
F1/2 Hotplate switches
S1 Line pilot lamp
P1 Rapid hotplate 2000 W - 230 V
P2 Regular hotplate 1000 W - 230 V
MTerminal block
TEarth connection
Wiring diagram - CE604 models
Fig. 19 CE604 wiring diagram
Key
F1/2/3/4 Hotplate switches
S1 Line pilot lamp
P1 Rapid hotplate 2000 W - 230 V
P2 Rapid hotplate 1500 W - 230 V
P3 Regular hotplate 1500 W - 230 V
P4 Regular hotplate 1000 W - 230 V
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
9

MTerminal block
TEarth connection
Installation checklist
Please check through the list provided to ensure correct installation.
• Is the product earthed?
• Check that the power supply cable is NOT touching the product.
This will ensure that the cable is not damaged by heat from the product.
• Is the product clamped down securely?
https://producthelp.fisherpaykel.com/au/Cook/Cooktops/Electric/Two_Burners/CE302CPX1/User_Guide_CE302CPX1/02_Installation_instructions
Updated: Sat, 09 Mar 2019 07:23:30 GMT
Powered by
10