Fisher & Paykel CI302DTB User manual

BLACK INDUCTION COOKTOP
CI302DTB, CI603DTB, CI604DTB,
CI764DTB, CI905DTB models
INSTALLATION GUIDE
NZ AU GB IE SG HK

SAFETY AND WARNINGS
!WARNING!
Electric Shock Hazard
Failure to follow this advice may result in
electric shock or death.
• Disconnect the appliance from the mains
electricity supply before carrying out any work
or maintenance.
• Connection to a good earth wiring system is
essential and mandatory.
• Alterations to the domestic wiring system must
only be made by a qualified electrician.
! WARNING!
Cut Hazard
Failure to use caution could result in injury.
• Take care: some edges are sharp.
READ AND SAVE THIS GUIDE
General Use
zRead these instructions carefully before installing this product.
zSave these instructions for the local electrical inspector’s use.
zInstallation must comply with your local building and local electricity regulations.
zThis appliance is to be installed and serviced only by Fisher & Paykel trained and supported
service technician or qualified person.
zThe manufacturer accepts no responsibility for the incorrect installation of appliances.
Incorrect installation may result in personal injury, damage to property and may invalidate
any warranty or liability claims.
zDo not modify this appliance.
zDo not use or store flammable materials on or near this appliance.
zPacking elements (eg plastic bags, polystyrene foam, staples, packing straps etc) and tools
should not be left around during and after installation, especially if they are within easy
reach of children, as these may cause serious injuries.
zMake sure you recycle the packaging material.
zBefore disposing of any appliance, make sure that it can no longer be used and that all
hazardous parts are removed or made harmless, so that children playing with the old
appliance cannot harm themselves.
zOnly genuine replacement parts may be used for servicing the appliance. These are
available from your nearest Fisher & Paykel Service Center.
zThis cooktop must be connected to the mains power supply only by a suitably
qualified person.
zDO NOT use adapters, reducers, or branching devices when connecting the cooktop to the
mains power supply to prevent overheating and fire.
zThe power supply cable must not touch any hot parts and must be positioned so that its
temperature will not exceed 75°C at any point.
zThis cooktop requires adequate supply of cool air to fully function. The base of the cooktop
must have direct unrestricted ventilation to the room where the cooktop is installed. There
must be a 4mm air gap at the front of the cooktop. (See ‘Venting Clearances’ page)
2

INSTALLATION CONSIDERATIONS
Before installation, please ensure the following:
za suitable disconnection switch is incorporated in the permanent wiring, mounted and
positioned to comply with the local wiring rules and regulations. A means of disconnection
with at least a 3 mm air gap contact separation in all poles must be incorporated into
the fixed wiring in accordance with the wiring rules, unless the local wiring rules allow for
alternative means.
zThe benchtop is made of a heat resistant material.
zThe power supply cable is not accessible through cupboard doors or drawers.
zThere is adequate flow of cool air from the cabinetry to the base of the cooktop. You
may ventilate from adjacent cupboards, but ensure that the available air supply will not
be restricted.
zThe ventilation area must be at least 50mm diameter holes or of equivalent area.
zThe isolating switch is easily accessible by the customer.
zUse heat-resistant and easy-to-clean finishes (such as ceramic tiles) for the wall surfaces
surrounding the cooktop.
zthe cooktop will not be installed directly above a dishwasher, fridge, freezer, washing
machine or clothes dryer, as the humidity may damage the cooktop electronics.
zDO NOT install the cooktop directly above a dishwasher, fridge, freezer, washing machine or
clothes dryer, as the humidity may damage the cooktop electronics.
zIf the cooktop is installed above an oven, ensure the oven has a built-in cooling fan.
zEnsure the installation complies with all clearance requirements and applicable standards
and regulations.
zConsult your local building authorities and by-laws if in doubt regarding the installation.
zTo eliminate the risk of burns or fire by reaching over heated surface units, cabinet storage
space located above the surface units should be avoided. If cabinet storage is to be
provided, the risk can be reduced by installing a rangehood that projects horizontally a
minimum of 127mm beyond the bottom of the overhead cabinets.
During installation, please ensure the following:
zSeal the exposed bare edges of the cutout with an oil-based paint or moisture-proof
polyurethane to prevent possible moisture creeping between the cooktop trim and
the benchtop.
zTake extreme care not to chip, crack, or break the top glass surfaces during installation.
A heavy metal tool or part accidentally dropped on the glass could damage it.
zIf, after following the instructions given, correct performance cannot be achieved, please
contact your nearest Fisher & Paykel Service Centre, Customer Care, or contact us through
our local website listed at the end of this document.
WARNING!
The owner carries all risk for flush mounting the cooktop. The owner must ensure the
cooktop has been cut out from the countertop before servicing can be carried out.
Fisher & Paykel will not be liable for any costs associated with removing or replacing a flush-
mounted and/or sealed-in product, nor for repairing any damage that may be incurred by
doing this.
PARTS SUPPLIED
We recommend installing products in separate cutouts with a minimum distance of 5mm
between the glass edges. If installing multiple products adjacent to each other within the
same cutout, a separate joining strip kit is required for installation. The kit is available from the
nearest Fisher & Paykel Authorised Service Centre or our website www.fisherpaykel.com.
If installing different products adjacent to each other (eg a wok burner next to an induction
cooktop), the minimum clearance measurements for the different products may vary. Always
use the greater distance.
BEFORE INSTALLATION MULTIPLE PRODUCT INSTALLATION
5mm
3

PARTS SUPPLIED TOOLS REQUIRED
WrenchClamping brackets
(4) and screws (4)
Hex key
Crosshead
screwdriver
Foam tape (1)
Router
Silicone Cutter
COMPONENTS REQUIRED
4

PRODUCT DIMENSIONS — 300MM MODELS
PRODUCT DIMENSIONS
CI302DTB
MM
A Overall height of cooktop 54
B Overall width of cooktop 299
C Overall depth of cooktop 530
D Height of chassis 48
E Width of chassis 260
F Depth of chassis 480
G Height of cooktop glass* 6
H Depth of front overhang of cooktop glass** 13
I Depth of rear overhang of cooktop glass 37
J Depth of side overhang of cooktop glass 20
* Includes flange and tape
** Includes front trim
Actual product dimension may vary by ± 2 mm.
FRONT
PROFILE
FRONT
A
E
B
G
J J
FRONT
PROFILE
PROFILE
D
F
HI
FRONT
PROFILE
PLAN ISOMETRIC
B
C
5

PRODUCT DIMENSIONS
CI603DTB CI604DTB
MM MM
A Overall height of cooktop 54 54
B Overall width of cooktop 599 599
C Overall depth of cooktop 530 530
D Height of chassis 48 48
E Width of chassis 552 552
F Depth of chassis 480 480
G Height of cooktop glass* 6 6
H Depth of front overhang of cooktop glass** 13 13
I Depth of rear overhang of cooktop glass 37 37
J Depth of side overhang of cooktop glass 24 24
Illustrations show CI603DTB model cooktop.
* Includes flange and tape
** Includes front trim
PRODUCT DIMENSIONS — 600MM MODEL
Actual product dimension may vary by ± 2 mm.
B
PROFILE
iSOMETRIC
FRONT
PLAN
FRONT
PROFILE
FRONT
PROFILE
FRONT
PROFILE
A
B
E
G
JJ
D
FH I
C
6

PRODUCT DIMENSIONS
CI764DTB
MM
A Overall height of cooktop 54
B Overall width of cooktop 759
C Overall depth of cooktop 530
D Height of chassis 48
E Width of chassis 722
F Depth of chassis 480
G Height of cooktop glass* 6
H Depth of front overhang of cooktop glass** 13
I Depth of rear overhang of cooktop glass 37
J Depth of side overhang of cooktop glass 19
* Includes flange and tape
** Includes front trim
PRODUCT DIMENSIONS — 760MM MODEL
Actual product dimension may vary by ± 2 mm.
FRONT
PROFILE
FRONT
PROFILE
FRONT
PROFILE
B
A
B
E
G
J J
D
F
HI
C
PROFILE
ISOMETRIC
FRONT
PLAN
7

PRODUCT DIMENSIONS
CI905DTB
MM
A Overall height of cooktop 54
B Overall width of cooktop 899
C Overall depth of cooktop 530
D Height of chassis 48
E Width of chassis 858
F Depth of chassis 484
G Height of cooktop glass* 6
H Depth of front overhang of cooktop glass** 13
I Depth of rear overhang of cooktop glass 33
J Depth of side overhang of cooktop glass 21
* Includes flange and tape
** Includes front trim
PRODUCT DIMENSIONS — 900MM MODEL
FRONT
PROFILE
FRONT
PROFILE
FRONT
PROFILE
PLAN
B
C
FRONT
A
E
B
G
J J
PROFILE
FH I
D
ISOMETRIC
Actual product dimension may vary by ± 2 mm.
8

CUTOUT DIMENSIONS — 300MM MODEL
CUTOUT DIMENSIONS
CI302DTB
MM
A Overall width of cutout 265
B Overall depth of cutout 490
C Corner radius of cutout max 10
D Offest overhang allowance 39
CUTOUT DIMENSIONS
CI302DTB
MM
A Overall width of routered recess 305
B Overall depth of routered recess 535
C Offset overhang allowance 39
D Height of routered recess 5
E Width of cutout 265
F Depth of cutout 490
G Corner radius of routered recess max 2
H Corner radius of cutout max 10
PROUD INSTALLATION FLUSH INSTALLATION
FRONT FRONT
PLAN PLAN
B fB
A E
A
C H
G
D C
D
9

CUTOUT DIMENSIONS — 600MM MODEL
CUTOUT DIMENSIONS
CI603DTB CI604DTB
MM MM
A Overall width of cutout 560 560
B Overall depth of cutout 490 490
C Corner radius of cutout max 10 max 10
D Offest overhang clearance 39 39
CUTOUT DIMENSIONS
CI603DTB CI604DTB
MM MM
A Overall width of routered recess 605 605
B Overall depth of routered recess 535 535
C Offset overhang allowance 39 39
D Height of routered recess 5 5
E Width of cutout 560 560
F Depth of cutout 490 490
G Corner radius of routered recess max 2 max 2
H Corner radius of cutout max 10 max 10
PROUD INSTALLATION FLUSH INSTALLATION
FRONT FRONT
PLAN PLAN
B fB
AE
A
CH
G
D C
D
10

CUTOUT DIMENSIONS — 760MM MODEL
CUTOUT DIMENSIONS
CI764DTB
MM
A Overall width of cutout 725
B Overall depth of cutout 490
C Corner radius of cutout max 10
D Offset overhang allowance 39
CUTOUT DIMENSIONS
CI764DTB
MM
A Overall width of routered recess 765
B Overall depth of routered recess 535
C Offset overhang allowance 39
D Height of routered recess 5
E Width of cutout 725
F Depth of cutout 490
G Corner radius of routered recess max 2
H Corner radius of cutout max 10
PROUD INSTALLATION FLUSH INSTALLATION
FRONT
PLAN
B
A
C
D
FRONT
PLAN
fB
E
A
H
G
C
D
11

CUTOUT DIMENSIONS — 900MM MODEL
CUTOUT DIMENSIONS
CI905DTB
MM
A Overall width of cutout 870
B Overall depth of cutout 494
C Corner radius of cutout max 10
D Offset overhang allowance 39
CUTOUT DIMENSIONS
CI905DTB
MM
A Overall width of routered recess 905
B Overall depth of routered recess 535
C Offset overhang allowance 39
D Height of routered recess 5
E Width of cutout 870
F Depth of cutout 494
G Corner radius of routered recess max 2
H Corner radius of cutout max 10
PROUD INSTALLATION FLUSH INSTALLATION
FRONT
PLAN
B
A
C
D
FRONT
PLAN
fB
E
A
H
G
C
D
12

g
I
J
CLEARANCE DIMENSIONS — 300MM MODEL
CLEARANCE DIMENSIONS
CI302DTB
MM
A Minimum clearance from glass surface to rangehood 650
B Minimum clearance below top of countertop to top of any appliance,
companion product or obstruction below cooktop 65
C Minimum clearance from side edges of cutout to nearest
combustible surface 30
D Maximum distance from right edge of cutout to center of junction box 762
E Minimum clearance below top of countertop to junction box 230
F Minimum clearance from countertop to overhead cabinet
(not directly above the cooktop) 450
G Maximum depth of overhead cabinetry 330
H Minimum distance between overhead cabinets either side of the cooktop 315
I Minimum clearance from rear edge of cutout to nearest
combustible surface 30
J
Minimum clearance from front edge of cutout to front edge of counter 35
c
c
H
b
f
d
f A
e
13

G
C
I
J
C
CLEARANCE DIMENSIONS — 600MM MODEL
CLEARANCE DIMENSIONS
CI603DTB CI604DTB
MM MM
A Minimum clearance from glass surface to rangehood 650 650
B Minimum clearance below top of countertop to top of any
appliance, companion product or obstruction below cooktop 65 65
C Minimum clearance from side edges of cutout to nearest
combustible surface 30 30
D Maximum distance from right edge of cutout to center of
junction box 762 762
E Minimum clearance below top of countertop to junction box 230 230
F Minimum clearance from countertop to overhead cabinet
(not directly above the cooktop) 450 450
G Maximum depth of overhead cabinetry 330 330
H Minimum distance between overhead cabinets either side of
the cooktop 315 315
I Minimum clearance from rear edge of cutout to nearest
combustible surface 30 30
J Minimum clearance from front edge of cutout to front edge
of counter 35 35
H
A
BE
D
F F
14

C
C
G
J
I
CLEARANCE DIMENSIONS — 760MM MODEL
CLEARANCE DIMENSIONS
CI764DTB
MM
A Minimum clearance from glass surface to rangehood 650
B Minimum clearance below top of countertop to top of any appliance,
companion product or obstruction below cooktop 65
C Minimum clearance from side edges of cutout to nearest
combustible surface 30
D Maximum distance from right edge of cutout to center of junction box 762
E Minimum clearance below top of countertop to junction box 230
F Minimum clearance from countertop to overhead cabinet
(not directly above the cooktop) 450
G Maximum depth of overhead cabinetry 330
H Minimum distance between overhead cabinets either side of the cooktop 315
I Minimum clearance from rear edge of cutout to nearest
combustible surface 30
J
Minimum clearance from front edge of cutout to front edge of counter 35
H
A
BED
F F
15

CLEARANCE DIMENSIONS — 900MM MODEL
CLEARANCE DIMENSIONS
CI905DTB
MM
A Minimum clearance from glass surface to rangehood 650
B Minimum clearance below top of countertop to top of any appliance,
companion product or obstruction below cooktop 65
C Minimum clearance from side edges of cutout to nearest
combustible surface 30
D Maximum distance from right edge of cutout to center of junction box 762
E Minimum clearance below top of countertop to junction box 230
F Minimum clearance from countertop to overhead cabinet
(not directly above wwthe cooktop) 450
G Maximum depth of overhead cabinetry 330
H Minimum distance between overhead cabinets either side of the cooktop 315
I Minimum clearance from rear edge of cutout to nearest
combustible surface 30
J
Minimum clearance from front edge of cutout to front edge of counter 35
H
A
BED
F F
G
C
I
J
C
16

VENTING CLEARANCES
Oven* with cooling fanDrawer or other obstruction
This cooktop requires adequate supply of cool air to fully function. The base of the cooktop
must have direct unrestricted ventilation to the room where the cooktop is installed. There
must be a 4mm air gap at the front of the cooktop.
CLEARANCE DIMENSIONS MM
A Minimum ventiliation gap at the front of the cooktop 4
B Minimum clearance from cooktop to drawer or other obstruction 65
C Minimum ventiliation gap at the rear of the cooktop 20
D Minimum diameter of cooling air hole 50
CLEARANCE DIMENSIONS MM
A Minimum ventilation gap at the front of the cooktop 4
B Minimum ventilation gap at the rear of the cooktop 20
C Minimum diameter of cooling air hole 50
*Some ovens require installation in a sealed box. Please refer you oven installation guide for more information.
A A
B
D C
C B
DRAWER OR OTHER OBSTRUCTION OVEN WITH COOLING FAN
17

2
1
3
Turn the cooktop upside down
on a protective cover.
Apply adhesive foam seal around
the glass overhang, 5mm from
the edge of the glass.
Ensure the adhesive side facing is
down to form a continuous seal
around the cooktop.
Trim the excess sealing material
using a sharp cutter or trimmer
knife.
Take care not to damage the
benchtop.
4
Gently lower the cooktop into the
cutout ensuring you have access
below the countertop to fit and
secure the brackets.
PROUD INSTALLATION
5
Locate the side brackets* to the
appropriate slots on the cooktop
chassis. The correct slot height
is determined by the thickness
of your countertop.
6
Tighten all screws to secure the
cooktop to the countertop.
Ensure cooktop is level.
*The number of brackets varies based on your cooktop model.
5mm
18

FLUSH INSTALLATION
2
1
5
Prepare the countertop for flush
installation. Use a router to cut
out the edges of the countertop
to specified depth (5mm).
Attach an adhesive tape along
the edges of the routered recess.
Mask off the area to be siliconed
ensuring both the cooktop and
countertop are protected.
Apply silicone in the gap
between benchtop and cooktop
Wipe off excess silicone.
6
Adhesive tape
3
4
Tighten all screws to secure the
cooktop to the countertop.
Ensure cooktop is level.
Locate the side brackets* to the
appropriate slots on the cooktop
chassis. The correct slot height
is determined by the thickness
of your countertop.
Gently lower the cooktop into the
cutout ensuring you have access
below the countertop to fit and
secure the brackets.
19

ELECTRICAL CONNECTION
Before connecting the cooktop to the mains power supply check that:
zThe domestic wiring system is suitable for the power drawn by the cooktop.
zThe voltage corresponds to the value given in the rating plate.
zThe power supply cable sections can withstand the load specified on the rating plate.
MODEL MAX. CURRENT DRAW MAX. LOAD VOLTAGE
CI302DTB* 16A 3700W 220 – 240V 1N ~
CI603DTB 32A 7050W 220 – 240V 2N ~
380 – 415V 2N ~
CI604DTB 32A 7050W 220 – 240V 2N ~
380 – 415V 2N ~
CI764DTB 32A 7400W 220 – 240V 2N ~
380 – 415V 2N ~
CI905DTB 43A 9800W 220 – 240V 3N ~
380 – 415V 3N ~
*The CI302DTB is supplied with a cable. This must be wired into a suitably rated plug, permanent connection outlet or
power isolator.
PE
1
2
3
4
5
PE
1
2
3
4
5
N
L
N
L1L2
PE
1
2
3
4
5
N
L1L3L2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
PE
1
2
3
4
5
N
L
N
L1L2
PE
1
2
3
4
5
N
L1L3L2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
PE
1
2
3
4
5
N
L
N
L1L2
PE
1
2
3
4
5
N
L1L3L2
PE
1
2
3
4
5
N
L
PE
1
2
3
4
5
PE
1
2
3
4
5
N
L
N
L1L2
PE
1
2
3
4
5
N
L1L3L2
PE
1
2
3
4
5
N
L
Single-phase connection (220 – 240 V~)
Single-phase connection (220 – 240 V~)
Two-phase connection (380 – 415V 2N~)
Three-phase connection (380 – 415V 3N~)
CI302DTB, CI603DTB, CI604DTB & CI764DTB MODELS
CI905DTB MODELS
20