Fisher & Paykel OR60SDBSX2 User manual

Installation instructions - Ceramic Glass Cooktop Models
Please follow the installation steps below to ensure your glass cooktop operates correctly.
Ceramic Glass Cooktop Models
Dimensions and clearances
• The cooker must be installed at least 50 mm away from any side walls higher than the cooktop. The cabinetry
surrounding the cooker must be made of heat-resistant material and must be able to withstand temperatures of
65 °C above room temperature.
• Do not install the cooker near flammable materials (eg curtains).
• If you stand the cooker on a pedestal, make sure you provide safety measures to keep it in place.
Fig. 15 Dimensions and correct distances from cooker
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
1

Levelling the cooker
Using the supplied
adjustable feet is
MANDATORY. For safety
reasons and to ensure
adequate ventilation, the
cooker chassis MUST NOT
sit directly on the floor, a
plinth, or other support
surface.
To fit the adjustable feet:
1. Rest the rear of the cooker on a piece of
packaging, exposing the base for fitting the
feet.
2. Screw the four feet to the cooker.
3. Stand the cooker and level it by screwing or
unscrewing the feet with an adjustable spanner.
Use the supplied nuts if necessary. See Figs.
16a- 16d.
Fig. 16a Fitting the adjustable feet (supplied with the
cooker in the feet kit)
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
2

Fig. 16b Do not use the supplied nuts for height adjustments
between 0 and 8 mm.
Fig. 16c Use the supplied nuts for height adjustments
between 8 and 15 mm.
Fig. 16d Levelling the cooker
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
3

Fixing the backguard
Before installing the cooker, assemble the backguard “B”
.
• The backguard “B” can be found packed at the
rear of the cooker.
1. Before assembling, remove any protective film/
adhesive tape.
2. Remove the three screws “A” from the rear of
the cooktop.
3. Assemble the backguard as shown and fix it by
screwing the three screws “A”.
Fig. 17 Assembling the backguard
Fitting the anti-tilt bracket
To restrain the appliance
and prevent it tipping
accidentally, fit a bracket to
its rear to fix it securely to
the wall. Make sure you
also fit the supplied lock pin
to the anti-tiit bracket.
To fit the anti-tilt bracket:
1. After you have located where the cooker is to be
positioned, mark on the wall the place where the
two screws of the anti-tilt bracket have to be fitted.
Fig. 18a Fitting the anti-tilt bracket
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
4

Please follow the indications given in Fig.18a.
2. Drill two 8 mm diameter holes in the wall and insert
the plastic plugs supplied.
Before drilling the holes,
check that you will not
damage any pipes or
electrical wires.
3. Loosely attach the anti-tilt bracket with the two
screws supplied.
4. Move the cooker to the wall and adjust the height
of the anti-tilt bracket so that it can engage in the
slot on the cooker’s back, as shown in Fig.18a.
5. Tighten the screws attaching the anti-tilt bracket.
6. Push the cooker against the wall so that the anti-tilt
bracket is fully inserted in the slot on the cooker’s
back.
7. Access the bracket and fit the lock pin;
• Remove the drawer (Fig. 18b).
• Fit the lock pin through the bracket, as shown
(Fig.18c).
• Refit the drawer.
Fig. 18b Removing the drawer
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
5

Fig. 18c Fitting the lock pin through the bracket
Connecting the power supply cable
This cooker must be connected to the electricity supply only by an authorised person.
To connect the power supply cable to the cooker, it is necessary to:
1. Remove the screws that hold cover “A” behind the cooker (Fig. 19b).
2. Position the U bolts “C” onto five-pole terminal block “B” according to the diagram in Fig. 19a.
3. Feed the power supply cable through the cable clamp “D”. The supply cable must be of a suitable size for the
current requirements of the appliance; see ‘Power supply cable section’.
4. Connect the phase wires to the terminal block “B” and the earth wire to the terminal “PE” as shown in Figs.
19a-19b.
5. Take up any slack in the cable and secure with the cable clamp “D”.
6. Replace the cover “A”.
The earth wire must be left about 30 mm longer than the others.
Voltage and power consumption
230 V~ 50 Hz 9700 W (diversity not applied) 240 V~ 50 Hz 10550 W (diversity not applied)
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
6

Power supply cable section
This cooker must be connected to the electrical supply using V105 insulated cable.
230-240 V~ 3 x 4 mm2
Fig. 19a Connection diagram Fig. 19b
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
7

Wiring Diagram
ELECTRIC DIAGRAM KEY
F1 Oven switch
F4/5 Energy regulators (single zones) F2/3
Energy regulators (double zones) LF Oven lamp
TM Oven thermostat
TS Safety thermostat
PR Electronic programmer
CTop heating element
GGrill heating element
SBottom heating element
V Fan motor
CIR Circular heating
element CR Residual heat
lamp
S1 Thermostat pilot lamp
S2 Radiant heaters pilot lamp
P3/4 Single zone radiant heaters
P1/2 Double zone radiant
heaters
MTerminal block
TEarth connection CF Cooling
fan motor TL Thermal overload
https://producthelp.fisherpaykel.com/au/Cook/Freestanding_Cookers/Electric/OR60SDBSX2/User_Guide_OR60SDBSX2_(59…
Updated: Fri, 08 May 2020 08:21:57 GMT
Powered by
8