Fisher & Paykel DishDrawer DD60 Series User manual

1
SERVICE MANUAL
NZ AU US SG GB TW EU
DISHDRAWER
DD60 DD24
models

1
FEATURED PRODUCT & CONTACT ADDRESSES
BRAND MODEL DESCRIPTION CA MARKET
Fisher & Paykel DD60DI9 Double integrated model 81209 AA
Fisher & Paykel DD60STI9 Single tall integrated model 81210 AA
Fisher & Paykel DD60SI9 Single integrated model 81211 AA
Fisher & Paykel DD60SLI9 Single 81212 AA
Fisher & Paykel DD60DDFX9 Double designer flat door stainless steel model 81213 AA
Fisher & Paykel DD60SDFTX9 Single designer falt door tall tub stainless steel model 81214 AA
Fisher & Paykel DD60SDFX9 Single designer flat door stainless model 81215 AA
Fisher & Paykel DD60DHI9 Double water softener integrated model 81234 GB
Fisher & Paykel DD60DDFHX9 Double designer flat door water softener stainless steel
model
81235 GB
Fisher & Paykel DD60SHI9 Single water softener integrated model 81236 GB
Fisher & Paykel DD60SHTI9 Single water softener tall tub integrated model 81237 GB
Fisher & Paykel DD60DHI9 Double water softener integrated model 81241 EU
Fisher & Paykel DD60SHI9 Single water softener integrated model 81242 EU
Fisher & Paykel DD60SHTI9 Single water softener tall tub integrated model 81244 EU
Fisher & Paykel DD60DI9 Double integrated model 81238 SG
Fisher & Paykel DD60SI9 Single integrated model 81240 SG
Fisher & Paykel DD60DIH9 Double integrated water softener model 81247 TW
Fisher & Paykel DD60SIH9 Single integrated water softener model 81248 TW
Fisher & Paykel DD60DHI9 Double water softener integrated model 81245 CN
Fisher & Paykel DD60SHTI9 Single water softener tall tub integrated model 81246 CN
Fisher & Paykel DD24DI9N Double integrated model 81218 US
Fisher & Paykel DD24DTI9N Double tall tub integrated model 81217 US
Fisher & Paykel DD24DHTI9N Double water softener tall tub integrated model 81216 US
Fisher & Paykel DD24DDFTX9N Double designer flat door tall tub stainless steel model 81222 US
Fisher & Paykel DD24SI9N Single integrated model 81221 US
Fisher & Paykel DD24STI9N Single tall tub integrated model 81220 US
Fisher & Paykel DD24SHTI9N Single water softener tall tub integrated model 81219 US
Fisher & Paykel DD24SDFTX9N Single designer flat door tall tub stainless steel model 81223 US
Fisher & Paykel Customer Services Pty
Ltd
PO Box 798, Cleveland, QLD 4163
A.C.N. 003 3335 171
19 Enterprise Street Cleveland, QLD 4163
Australia
tel: [phone]
fax: [phone]
email: customer.car[email protected]
Fisher & Paykel Appliances Ltd
PO Box 58-546
Botany, Manukau 2163
78 Springs Rd
East Tamaki
Manukau 2013
New Zealand
tel: [phone]
fax: [phone]
email: customer.car[email protected].nz
Fisher & Paykel Appliances
150 Ubi Avenue 4
#03-01A
Ubi Biz-Hub
408825
Singapore
tel: [phone]
Customer Care: [phone]
email: customer.care@fisherpaykel.co.sg
Fisher & Paykel Appliances Inc
695 Town Center Drive
Suite 180
Costa Mesa, CA 92626-1902
USA
Telephone: [phone]
Fisher & Paykel Appliances
Unit D2
North Dublin Corporate Park
Swords
Co Dublin
Ireland
tel: [phone]
fax: [phone]
email: customer.care@fisherpaykel.ie
Fisher & Paykel Appliances Ltd U.K
Maidstone Road
Kingston
Milton Keynes
Buckinghamshire
England, MK10 0BD
tel: [phone]
fax: [phone]
email: customer.care@fisherpaykel.co.uk

2
CONTENTS
CONTENTS
1 HEALTH & SAFETY 4
2 SPECIFICATIONS 6
2.1 Product Dimensions 6
2.1.1 AA GB EU SG Double Designer Models 6
2.1.2 AA GB EU SG Single Designer Models 7
2.1.3 US CA TW Double Designer Models 8
2.1.4 US CA TW Single Designer Models 9
2.1.5 AA GB EU SG Double Integrated Models 10
2.1.6 AA GB EU SG Single Integrated Models 11
2.1.7 US CA TW Double Integrated Models 12
2.1.8 US CA TW Single Integrated Models 13
2.2 Plumbing Requirements 14
2.2.1 AA GB EU SG Double Models 14
2.2.2 AA GB EU SG Single Models 14
2.2.3 US CA Double Models 15
2.2.4 US CA Single Models 16
2.3 Electrical Specifications 18
2.3.1 Alternate Electrical Specifications 18
2.4 Component Specifications 18
2.5 Wash Profiles 19
3 MODEL NUMBER LOCATION & IDENTIFICATION 22
3.1 Model Number & Product Code 22
3.2 Serial Number 22
4 TECHNICAL OVERVIEW 23
4.1 Chassis 23
4.2 Drawer Fronts 23
4.3 Electronics 23
4.4 Drying Fan 24
4.5 Tub Home Sensor 25
4.6 Tub Display 25
4.7 Knock to Pause Sensor (integrated model only) 25
4.8 Door Button (designer model only) 25
4.9 Motor 26
4.10 Motor Rotor 26
4.11 Spray Arm 26
4.12 Filter Plate 26
4.13 Drain Filter 27
4.14 Lid System 27
4.15 Filling with Water 28
4.16 Heating 29
4.17 Drain Cycle 30
4.18 Water Softener (some models only) 31
5 OPERATION 32
5.1 Designer Display 32
5.2 Integrated Display 32
5.3 Using the Wash Modifiers 33
5.4 Using the Sanitize 33
5.5 User Preference Settings 34
5.5.1 Adjusting the Knock Sensitivity on Integrated Models 34
5.6 Removing the Drain Filter and Filter Plate to Clean 37
5.7 Cleaning the Spray Arm 39
5.8 Fold Down Tines 40

3
CONTENTS
6 DIAGNOSTICS 41
6.1 Entering Diagnostics 41
6.2 Getting into Hardware Output Mode (HO) 42
6.3 Getting into Fast Test Cycle 44
6.4 Getting into Continuous Cycle 44
7 FAULT DIAGNOSTICS 45
7.1 Troubleshooting 45
7.2 Fault Codes 49
7.3 Component Testing 57
8 SERVICING PROCEDURES 58
8.1 Removing the Drawer Front 58
8.2 Dissassembly of the Inner Door Panel 58
8.3 Removal of the Designer Door Button 59
8.4 Removal of the Top Cap 59
8.5 Removal of the Water Softener ( some models only) 60
8.6 Removal of the Strainer ( some models only) 60
8.7 Removing the Wash Controller 61
8.8 Removing the Dispenser 61
8.9 Removing the Drying Fan & Flap Valve 61
8.10 Removing the Filter Plate 62
8.11 Removing the Motor Rotor 62
8.12 Removing the Pump Cap Cover 62
8.13 Removing the Tub 63
8.14 Removing the Kickstrip 63
8.15 Removing the Lower Cowling 63
8.16 Removing the wiring cover 64
8.17 Removing the Heater 65
8.18 Replacing the Motor 66
8.19 Replacing a fill Hose,Drain Hose or Wiring Harness 67
8.20 Replacing the Motor Controller 70
8.21 Flood Sensor Harness 71
8.22 Replacing the Water Valve 71
8.23 Replacing the Lid Actuator 72
8.24 Replacing the Lid Assembly 72
8.24 Replacing the Yoke 73
8.25 Replacing the Side Rail 74
8.26 Replacing the Chassis Trim 74
8.27 Replacing the Temperature Sensor 74
9 WIRING DIAGRAM 75
10 NOTES 76

4
1 HEALTH & SAFETY
Important !
PLEASE RETAIN THIS MANUAL FOR FUTURE REFERENCE.
When servicing the Dishwasher, health and safety issues must be considered at all times.
D
1.1 Health & Safety
Note: Specific safety issues are listed below with their appropriate icon. These are illustrated throughout
the service information.
1.1.1 Electrical Safety
Ensure the mains power has been disconnected before servicing the DishDrawer™. If the
mains supply is required to be on to service the DishDrawer™, make sure it is turned off
when removing any electrical component or connection to avoid electrical shock.
1.1.2 Electrostatic Discharge
An anti-static strap is to be used as electrical static discharge (ESD) protection when servicing
electronic components.
1.1.3 Good Working Practices
Ensure the work area is in a tidy and orderly condition at all times so as not to cause a hazard
while service work is being completed. Always clean and tidy the DishDrawer™ and work area
after service is completed.
1.1.4 Isolate Water Supply
Turn o the water connection tap before servicing.
1.1.5 Water Leak Check
Check for water leaks as part of the testing after the service has been completed.
1.1.6 Insulation Test
Megger test to check insulation.
Warning: Short together the phase and neutral pins on the plug so as not to damage any
electronic circuitry.
1.1.7 Solvent and Excessive Heat Damage
Solvents and excessive heat can damage plastic surfaces.
1.1.8 Sheet Metal Edges
When working around cut sheet metal edges use appropriate gloves or protection to eliminate
the chance of receiving a laceration.
D
D
D
D
D
D
D

5
1.2 Specialised Tools
1.1.9 Diagnostics
While in diagnostics some safety devices are bypassed. Ensure you do
not run components unattended.
They may overheat, flood or burn out or cause water damage.
D
1.2.1 Static Strap
For servicing this product, some specialist tools are required.
An anti static strap is required to prevent ESD (electrocstatic discharge) when handling electronic
components.
1.3 Training Videos
In section 8, Service Procedures, you will find web links to take you through to training videos on
specific service procedures. These training videos are also available on the service website Cool Blue
World.
1 HEALTH & SAFETY

6
2 SPECIFICATIONS
2.1 Product Dimensions
2.1.1 AA GB EU SG Double Designer Models
3
3 PRODUCT DIMENSIONS
B
D
O
E
N
F
A
C
M
L
G
J
I
H
K
PLAN
PROFILEFRONT
DD60DDF
PRODUCT DIMENSIONS MM
AOverall height of product1820-8802
BOverall width of product 599
COverall depth of product 573
DDepth of chassis (to back of front drawer panel) 553
EDepth of drawer front panel 20
FHeight of chassis1811
GHeight of drawer front panels 717
HHeight of upper drawer front panel 398
IHeight of lower drawer front panel 312
JHeight from top of drawer front panel to top of chassis 2
KVentilation gap between drawer front panels 7
LHeight of toekick (customisable) 70-120
MDepth from front of drawer panel to front of toekick (adjustable)338-54
NHeight of levelling feet (adjustable) 9-692
OMaximum extension of drawer 547
1 includes 2mm high bracket slots 2 depending on adjustment of levelling feet
3 adjustable to match toekick recess on adjoining cabinetry
4
4 CABINETRY DIMENSIONS
Minimum clearances from adjacent cabinetry
min. 13 mm
clearance
from a corner
cupboard
Bracket slots
min. 2 mm
clearance
to adjacent
cupboard door
R
Q
P
S
T
PROFILE
PLAN
DD60DDF
CABINETRY DIMENSIONS MM
PInside height of cavity* min. 820
QInside width of cavity 600
RInside depth of cavity min. 560
SRecommended height of adjacent cabinet space 720
THeight of toekick space* 100-160
* depending on adjustment of levelling feet

7
2.1.2 AA GB EU SG Single Designer Models
2 SPECIFICATIONS
6
4 CABINETRY DIMENSIONS
DD60SI
DD60SHI
DD60SLI
DD60STI
DD60SHTI
DD60STI
DD60SHTI
CABINETRY DIMENSIONS MM MM MM
JInside height of cavity min. 412 456 480
KInside width of cavity 600 600 600
LInside depth of cavity min. 560 min. 560 min. 560
()
min.
412mm 456mm 480mm
JJJ
Dishwasher Dishwasher Dishwasher
DD60SI, DD60SLI, DD60SHI
STANDARD HEIGHT INTEGRATED MODEL
DD60STI, DD60SHTI
TALL HEIGHT INTEGRATED MODEL
(Installed in a 456mm high cavity)
D60STI, DD60SHTI
TALL HEIGHT INTEGRATED MODEL
(Installed in a 480mm high cavity)
Compact
Oven
Full Size
Oven
Cavity height options allow you to match dishwasher with your cabinetry or companion products
STANDARD
HEIGHT
TALL
HEIGHT
(Installed in a
456mm high
cavity)
TALL
HEIGHT
(Installed in a
480mm high
cavity)
Q
P
Bracket slots
PLAN
Minimum clearances from adjacent cabinetry
min. 13 mm
clearance
from a corner
cupboard
min. 2 mm
clearance
to adjacent
cupboard door
Cavity Bracket (480mm cavity height)
Custom Filler Panel (other heights)
PROFILE
TALL HEIGHT MODELS ONLY
If your cavity height leaves a visible gap
under your countertop when you open
the drawer:
Fit the supplied cavity bracket (or
a custom cavity filler panel) before
installation in order to conceal any
gap at the top of the cavity left after
installation.
J
K
L
3
3 PRODUCT DIMENSIONS
DD60SDF DD60SDFT
PRODUCT DIMENSIONS MM MM
AOverall height of product1410 4782
BOverall width of product 599 599
COverall depth of product 573 573
DDepth of chassis (to back of front drawer panel) 553 553
EDepth of drawer front panel 20 20
FHeight of drawer front panel 398 470
GHeight of chassis1410 454
HHeight from top of drawer front panel to top of chassis
22
IVentilation gap below drawer front panel
99
JMaximum extension of drawer 547 547
1 includes 2mm high bracket slots
2 includes fitted cavity bracket
H
I
FG
C
A
B
D
O
E
PLAN
PROFILEFRONT
STANDARD
HEIGHT
TALL
HEIGHT

8
2 SPECIFICATIONS
2.1.3 US CA TW Double Designer Models
5
4 PRODUCT DIMENSIONS
B
D
O
E
N
F
A
C
M
L
G
J
I
H
K
PLAN
PROFILEFRONT
Handles may vary
DD24DDFT DD24DV2T
PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)
AOverall height of product 134 - 36 3/8” (864-924) 234 - 36 3/8” (864-924) 2
BOverall width of product 23 9/16” (599) 23 13/16” (605)
COverall depth of product (excl. handle) 22 9/16” (573) 22 3/4” (578)
DDepth of chassis (to back of front drawer panel) 21 3/4” (553) 21 3/4” (553)
EDepth of drawer front panel (excl. handle) 13/16” (20) 1” (25)
FHeight of chassis 133 11/16” (855) 33 11/16” (855)
GHeight of drawer front panels 30” (762) 30” (762)
HHeight of upper drawer front panel 17 3/8” (442) 17 3/8” (442)
IHeight of lower drawer front panel 12 1/4” (312) 12 1/4” (312)
JHeight from top of drawer front panel to top of chassis 1/16” (2) 1/16” (2)
KVentilation gap between drawer front panels 5/16” (8) 5/16” (8)
LHeight of toekick (customisable) 2 13/16 - 5” (72-127) 2 13/16 - 5” (72-127)
MDepth from front of drawer panel to front of toekick (adjustable) 31 1/2 - 4” (38-102) 1 11/16 - 4 3/16” (43-107)
NHeight of leveling feet (adjustable) 3/8 - 2 11/16” (9-69) 23/8 - 2 11/16” (9-69) 2
OMaximum extension of drawer 21 9/16” (547) 21 9/16” (547)
1 includes 1/16” (2mm) high bracket slots 2 depending on adjustment of leveling feet
3 adjustable to match toekick recess on adjoining cabinetry
6
5 CABINETRY DIMENSIONS
Minimum clearances from adjacent cabinetry
Bracket slots
R
Q
P
S
T
PROFILE
PLAN
DD24DDFT DD24DV2T
CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)
PInside height of cavity* min. 34” (864) min. 34” (864)
QInside width of cavity 23 5/8” (600) 24” (610)
RInside depth of cavity min. 22 1/16” (560) min. 22 1/16” (560)
SRecommended height of adjacent cabinet space 30” (762) 30” (762)
THeight of toekick space* 3 15/16” - 6 5/16” (100-160) 3 15/16” - 6 5/16” (100-160)
* depending on adjustment of leveling feet
min. 1/2” (13 mm)
clearance from a
corner cupboard
min. 1/16” (2 mm)
clearance
to adjacent
cupboard door

9
2 SPECIFICATIONS
2.1.4 US CA TW Single Designer Models
5
4 PRODUCT DIMENSIONS
H
I
FG
C
A
B
D
O
E
PLAN
PROFILEFRONT
DD24SDFT DD24SV2T
PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)
AOverall height of product
1
17 7/8” (454)
2
17 7/8” (454)
BOverall width of product
23 9/16” (599) 23 13/16” (605)
COverall depth of product
22 9/16” (573) 22 3/4” (578)
DDepth of chassis (to back of front drawer panel)
21 3/4” (553) 21 3/4” (553)
EDepth of drawer front panel (excl. handle)
13/16” (20) 1” (25)
FHeight of drawer front panel
18 1/2” (470) 17 3/8” (442)
GHeight of chassis
1
17 7/8” (454) 17 7/8” (454)
HHeight from top of drawer front panel to top of chassis
1” (26) 1/16” (2)
IVentilation gap below drawer front panel
3/8” (9) 3/8” (9)
JMaximum extension of drawer
21 9/16” (547) 21 9/16” (547)
1
includes 1/16” (2mm) high bracket slots
2
includes fitted cavity bracket
Handles may vary
6
5 CABINETRY DIMENSIONS
Minimum clearances from adjacent cabinetry
Bracket slots
R
Q
K
PROFILE
PLAN
DD24SDFT DD24SV2T
CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)
KInside height of cavity 18 7/8” (480) 17 15/16” (456)
LInside width of cavity 23 5/8” (600) 24” (610)
MInside depth of cavity min. 22 1/16” (560) min. 22 1/16” (560)
min. 1/2” (13 mm)
clearance from a
corner cupboard
min. 1/16” (2 mm)
clearance
to adjacent
cupboard door

10
2 SPECIFICATIONS
2.1.5 AA GB EU SG Double Integrated Models
5
3 PRODUCT DIMENSIONS
B
D
N
E
A
G
H
I
J
C
F
M
L
K
PLAN
PROFILEFRONT
DD60DI
DD60DHI
PRODUCT DIMENSIONS MM
A
Overall height of product
1, 2
820-880
B
Overall width of product
599
C
Overall depth of product
3
571
D
Depth of chassis (to back of front drawer panel)
553
E
Depth of drawer front panel
16-20
F
Height of chassis
1
811
G
Height of drawer front panels
min. 717
H
Height of upper drawer front panel
min. 398
I
Height of lower drawer front panel
311-360
J
Ventilation gap between drawer front panels
8
K
Height of toekick (customisable)
58-118
L
Depth from front of drawer panel to front of toekick (adjustable)
4, 5
40-100
M
Height of leveling feet (adjustable)
2
9-69
N
Maximum extension of drawer
3
545
1
includes 2mm high bracket slots
2
depending on adjustment of leveling feet
3
assuming front panel thickness of 18mm
4
adjustable to match toekick recess on adjoining cabinetry
5
assuming custom toekick panel thickness of 18mm; if recess is between 50-84mm deep, the panel will need to be cut out
- see step ‘Custom panel calculations’
6
Q
P
O
R
S
4 CABINETRY DIMENSIONS
Minimum clearances from adjacent cabinetry
min. 13 mm
clearance
from a corner
cupboard
Bracket slots
min. 2 mm
clearance
to adjacent
cupboard door
PROFILEPLAN
DD60DI
DD60DHI
CABINETRY DIMENSIONS MM
O
Inside height of cavity* min. 820
P
Inside width of cavity 600
Q
Inside depth of cavity min. 560
R
Recommended height of adjacent cabinet space 720
S
Height of toekick space* 100-160
* depending on adjustment of levelling feet

11
2 SPECIFICATIONS
5
3 PRODUCT DIMENSIONS
C
B
H
F G
A
D
I
E
PLAN
PROFILEFRONT
DD60SLI
DD60SI
DD60SHI
DD60STI
DD60SHTI
DD60STI
DD60SHTI
PRODUCT DIMENSIONS MM MM MM MM
AOverall height of product 1410 410 454 478 2
BOverall width of product 599 599 599 599
COverall depth of product 3571 571 571 571
DDepth of chassis (to back of front drawer panel) 553 553 553 553
EDepth of drawer front panel 16-20 16-20 16-20 16-20
FHeight of drawer front panel min. 408 min. 398 4min. 452 5min. 476 5
GHeight of chassis 1410 410 454 454
HVentilation gap below drawer front panel min. 8 min. 2 min. 2 min. 2
IMaximum extension of drawer 3545 545 545 545
1 includes 2mm high bracket slots 2 includes fitted cavity bracket
3 assuming a front panel thickness of 18mm 4 recommended for a 2mm ventilation gap below panel, if cavity height is 412mm
5 recommended for a 2mm ventilation gap below panel
STANDARD
HEIGHT
STANDARD
HEIGHT
TALL
HEIGHT
(Installed in a
18” (456mm)
high cavity)
TALL
HEIGHT
(Installed in a
18 7/8” (480mm)
high cavity)
6
4 CABINETRY DIMENSIONS
DD60SI
DD60SHI
DD60SLI
DD60STI
DD60SHTI
DD60STI
DD60SHTI
CABINETRY DIMENSIONS MM MM MM
JInside height of cavity min. 412 456 480
KInside width of cavity 600 600 600
LInside depth of cavity min. 560 min. 560 min. 560
()
min.
412mm 456mm 480mm
JJJ
Dishwasher Dishwasher Dishwasher
DD60SI, DD60SLI, DD60SHI
STANDARD HEIGHT INTEGRATED MODEL
DD60STI, DD60SHTI
TALL HEIGHT INTEGRATED MODEL
(Installed in a 456mm high cavity)
D60STI, DD60SHTI
TALL HEIGHT INTEGRATED MODEL
(Installed in a 480mm high cavity)
Compact
Oven
Full Size
Oven
Cavity height options allow you to match dishwasher with your cabinetry or companion products
STANDARD
HEIGHT
TALL
HEIGHT
(Installed in a
456mm high
cavity)
TALL
HEIGHT
(Installed in a
480mm high
cavity)
Q
P
Bracket slots
PLAN
Minimum clearances from adjacent cabinetry
min. 13 mm
clearance
from a corner
cupboard
min. 2 mm
clearance
to adjacent
cupboard door
Cavity Bracket (480mm cavity height)
Custom Filler Panel (other heights)
PROFILE
TALL HEIGHT MODELS ONLY
If your cavity height leaves a visible gap
under your countertop when you open
the drawer:
Fit the supplied cavity bracket (or
a custom cavity filler panel) before
installation in order to conceal any
gap at the top of the cavity left after
installation.
J
K
L
2.1.6 AA GB EU SG Single Integrated Models

12
2.1.7 US CA TW Double Integrated Models
5
4 PRODUCT DIMENSIONS
STANDARD
HEIGHT
MODELS
TALL
HEIGHT
MODELS
PLAN
PROFILEFRONT
DD24DI
DD24DTI
DD24DHTI
PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)
AOverall height of product 1, 2 32 5/16 - 34 5/8” (820-880) 34 - 36 3/8” (864-924)
BOverall width of product 23 9/16” (599) 23 9/16” (599)
COverall depth of product 322 1/2” (571) 22 1/2” (571)
DDepth of chassis (to back of front drawer panel) 21 3/4” (553) 21 3/4” (553)
EDepth of drawer front panel 5/8” - 13/16” (16-20) 13/16” (20)
FHeight of chassis 131 15/16” (811) 33 11/16” (855)
GHeight of drawer front panels min. 28 1/4” (717) 29 15/16” (761)
HHeight of upper drawer front panel min 15 11/16” (398) min. 17 3/8” (442)
IHeight of lower drawer front panel 12 1/4” - 14 3/16” (311-360) 12 1/4” - 14 3/16” (311-360)
JVentilation gap between drawer front panels 5/16” (8) 5/16” (8)
KHeight of toekick (customisable) 2 1/4” - 4 5/8” (58-118) 2 1/4” - 4 5/8” (58-118)
LDepth from front of drawer panel to front of toekick (adjustable) 4, 5 1 9/16” - 3 15/16” (40-100) 1 9/16” - 3 15/16” (40-100)
MHeight of leveling feet (adjustable) 23/8 - 2 11/16” (9-69) 3/8 - 2 11/16” (9-69)
NMaximum extension of drawer 321 7/16” (545) 21 7/16” (545)
1 includes 1/16” (2mm) high bracket slots 2 depending on adjustment of leveling feet 3 assuming front panel thickness of 11/16” (18mm)
4 adjustable to match toekick recess on adjoining cabinetry
5 assuming custom toekick panel thickness of 11/16” (18mm); if recess is between 1 15/16”-3 5/16” (50-84mm) deep, the panel will need to be cut out -
see step ‘Custom panel calculations’
A
K
LM
G
H
J
I
F
D
N
E
C
B
6
5 CABINETRY DIMENSIONS
Minimum clearances from adjacent cabinetry
STANDARD
HEIGHT
MODELS
TALL
HEIGHT
MODELS
DD24DI
DD24DTI
DD24DHTI
CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)
OInside height of cavity* min. 32 5/16” (820) min. 34” (864)
PInside width of cavity 23 5/8” (600) 23 5/8” (600)
QInside depth of cavity min. 22 1/16” (560) min. 22 1/16” (560)
RRecommended height of adjacent cabinet space 30” (762) 30” (762)
SHeight of toekick space* 2 3/8 - 4 3/4” (60-120) 3 15/16” - 6 5/16” (100-160)
* depending on adjustment of leveling feet
min. 1/2” (13 mm)
clearance from a
corner cupboard
min. 1/16” (2 mm)
clearance
to adjacent
cupboard door
Bracket slots
PROFILE
PLAN
P
QO
R
S

13
2.1.8 US CA TW Single Integrated Models
5
4 PRODUCT DIMENSIONS
DD24SI
DD24STI
DD24SHTI
PRODUCT DIMENSIONS INCHES (MM) INCHES (MM)
AOverall height of product 116 1/8” (410) min. 17 7/8” (454)
BOverall width of product 23 9/16” (599) 23 9/16” (599)
COverall depth of product 222 1/2” (571) 22 1/2” (571)
DDepth of chassis (to back of front drawer panel) 21 3/4” (553) 21 3/4” (553)
EDepth of drawer front panel 5/8” - 13/16” (16-20) 5/8” - 13/16” (16-20)
FHeight of drawer front panel min. 16 1/16” (408) 3min. 17 13/16” (452) 4
GHeight of chassis 116 1/8” (410) 17 7/8” (454)
HVentilation gap below drawer front panel min. 1/6” (2) min. 1/6” (2)
IMaximum extension of drawer 221 7/16” (545) 21 7/16” (545)
1 includes 1 ⁄16” (2mm) high bracket slots 2 assuming a front panel thickness of 11/16” (18mm)
3 recommended for a 1 ⁄16” (2mm) ventilation gap below panel, if cavity height is 16 1/4” (412mm)
4 recommended for a 1 ⁄16” (2mm) ventilation gap below panel
PLAN
PROFILEFRONT
A
H
F
D
I
E
BC
G
STANDARD
HEIGHT
MODELS
TALL
HEIGHT
MODELS
6
5 CABINETRY DIMENSIONS
DD24SI
DD24STI
DD24SHTI
CABINETRY DIMENSIONS INCHES (MM) INCHES (MM)
J
Inside height of cavity
min. 16 1/4” (412) min. 18” (456)
K
Inside width of cavity
23 5/8” (600) 23 5/8” (600)
L
Inside depth of cavity
min. 22 1/16” (560) min. 22 1/16” (560)
Minimum clearances from adjacent cabinetry
min. 1/2” (13 mm)
clearance from a
corner cupboard
Custom Filler Panel
min. 1/16” (2 mm)
clearance to adjacent
cupboard door
PROFILE
PROFILE
Bracket slots
PLAN
If your cavity height leaves a visible gap
under your countertop when you open
the drawer:
Fit the supplied cavity bracket (or
a custom cavity filler panel) before
installation in order to conceal any
gap at the top of the cavity left after
installation.
J
J
K
L
STANDARD
HEIGHT
MODELS
TALL
HEIGHT
MODELS

14
2 SPECIFICATIONS
2.2 Plumbing Requirements
2.2.1 AA GB EU SG Double Models
2.2.2 AA GB EU SG Single Models
20
!7 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
1
2
1
23
If space is limited
for fixing, push
hose through drain
hose support
to required height
If space is limited
for fixing, push
hose through drain
hose support
to required height
Dishwasher using drain hose joiner onto sink trap/waste tee
min. radius
200 mm
750 - 882.5 mm
750 - 882.5 mm
min. 500 mm
min. 500 mm
min. radius
200 mm
step 16
step 16
Supplied drain
hose joiner to suit
19 mm waste tee
Ensure drain hose is routed
straight to joiner. Remove excess
drain hose material if necessary.
Do not shorten the inlet hose.
Dishwasher and Ø 38 mm Standpipe
IMPORTANT!
Do not connect the drain hoses
to a Waste Disposal Unit, as this
type of connection may lead to a
blockage in the drain hoses.
750-882.5 mm 750-882.5 mm
38mm
max.
120mm
max.
120mm
19
!7 THERE ARE TWO DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
1
2
3
1
2
If space is limited
for fixing, push
hose through drain
hose support
to required height
If space is limited
for fixing, push
hose through drain
hose support
to required height
Dishwasher using drain hose joiner onto sink trap/waste tee
min. radius
200 mm
750 - 882.5 mm
750 - 882.5 mm
min. 500 mm
min. 500 mm
min. radius
200 mm
step 18
step 18
Supplied drain
hose joiner to suit
19 mm waste tee
Ensure drain hose is routed
straight to joiner. Remove excess
drain hose material if necessary.
Do not shorten the inlet hose.
Dishwasher and Ø 38 mm Standpipe
IMPORTANT!
Do not connect the drain hoses
to a Waste Disposal Unit, as this
type of connection may lead to a
blockage in the drain hoses.
750-882.5 mm 750-882.5 mm
38mm
max.
120mm

15
2 SPECIFICATIONS
2.2.3 US CA Double Models
14
1
2
!4 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
DRAINAGE OPTION 1
Dishwasher and Ø 1 1/2” (38 mm) Standpipe
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
min. R 8”
(200 mm)
29 1/2”-34 3/4” (750-882.5 mm)
1 1/2”
(38mm)
29 1/2 - 34 3/4” (750-883 mm)
Screw Drain hose
support to back wall
at correct height
If space is limited
for fixing, push
hose through drain
hose support
to required height max.
4 3/4”
(120mm)
step 15
min. 19 11/16” (500 mm)
15
min. R 8”
(200 mm)
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
DRAINAGE OPTION 2
Dishwasher using Air Break with Drain Hose Joiner
37 3/8” (950 mm)
Max. height to top
of Air Break
(countertop or
wall mounted)
1
2
step 15
Secure both drain
hoses to drain hose
joiner and secure to
Air Break

16
2 SPECIFICATIONS
16
1
2
3
min. R 8”
(200 mm)
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
DRAINAGE OPTION 3
Dishwasher using drain hose joiner onto sink trap/waste tee
29 1/2 - 34 3/4” (750-883 mm)
step 15
Supplied drain
hose joiner to suit
Ø 3/4” (19 mm)
waste tee
Ensure drain hose is routed
straight to joiner. Remove excess
drain hose material if necessary.
Do not shorten the inlet hose.
29 1/2”-34 3/4” (750-882.5 mm)
Screw Drain hose
support to back wall
at correct height
If space is limited
for fixing, push
hose through drain
hose support
to required height
max.
4 3/4“
(120mm)
min. 19 11/16” (500 mm)
2.2.4 US CA Single Models
13
1
2
!3 THERE ARE THREE DIFFERENT PLUMBING AND DRAINAGE OPTIONS. CHOOSE WHICH IS MORE SUITABLE.
DRAINAGE OPTION 1
Dishwasher and Ø 1 1/2” (38 mm) Standpipe
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
min. R 8”
(200mm)
29 1/2” - 34 3/4” (750 - 882.5 mm)
1 1/2”
(38mm)
29 1/2 - 34 3/4” (750 - 883mm)
Screw Drain hose
support to back wall
at correct height
If space is limited
for fixing, push
hose through drain
hose support
to required height
max.
4 3/4“
(120mm)
step 14
min. 19 11/16” (500mm)

17
2 SPECIFICATIONS
14
1
2
min. R 8”
(200mm)
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
DRAINAGE OPTION 2
Dishwasher using Air Break with Drain Hose Joiner
37 3/8” (950mm)
Max. height to top
of Air Break
(countertop or
wall mounted)
step 14
Secure drain hose to
drain hose joiner and
secure to Air Break
15
3
1
2
min. R 8”
(200mm)
IMPORTANT!
Ensure that drain
connection will comply with
local plumbing regulations.
DRAINAGE OPTION 3
Dishwasher using drain hose joiner onto sink trap/waste tee
29 1/2 - 34 3/4” (750 - 883mm)
step 14
Supplied drain
hose joiner to suit
Ø 3/4” (19 mm)
waste tee
Ensure drain hose is routed
straight to joiner. Remove excess
drain hose material if necessary.
Do not shorten the inlet hose.
29 1/2”- 34 3/4” (750 - 882.5mm)
Screw Drain hose
support to back wall
at correct height
If space is limited
for fixing, push
hose through drain
hose support
to required height max.
4 3/4”
(120mm)
min. 19 11/16” (500mm)

18
2 SPECIFICATIONS
COMPONENT SPECIFICATION
Controller AA, GB, SG, PF 240V
US, TW 120v
Water inlet valve 24v DC
65 +- 10 Ohms per coil
2.5L per minute
Dispenser coils 24V DC
65 +- 10 Ohms
Rinse aid tanks AA, SG, PF 50 mls (approx 25 washes)
US, TW 3.05 cubic inches
Motor
Drain speed
Wash speed
DC 3 phase brushless
5000rpm
2200 - 2800rpm
Stator 8 Ohms per winding
16 Ohms phase to phase
Heater AA, SG, PF 230V - 920W
55 - 60 Ohm
US, TW 20V -570W
24-27 Ohm
Thermal cut out temp 120 Deg C +- 6.5 Deg C
248 Deg F +- 42 Deg F
Temperature sensor 12000 Ω @ 20 oC (68 oF)
8300 Ω @ 30 oC (86oF)
3000 Ω @ 60 oC (140oF)
Water inlet hose Pressure rating
Length from chassis edge
(view from front)
1MPa (145psi) max
1650mm LH side
1250mm RH side
Water pressure Incoming water
pressure ratings
1MPa (145psi) max
1650mm (64 3/4’’) LH side
1250mm (49’’) RH side
Drain hose 2000mm (78 1/2’’) from LH side
1800mm (70 1/2’’) from RH side
Power cord AA, SG, PF 1650mm
US, TW 29 1/2’’
Drying fan 24V brushless DC motor
0.27A
Lid actuator 24V DC
MARKET VOLTAGE (V) FREQUENCY (HZ) CURRENT ( A)
AA, SG, PF 220/240 50 10
US, TW 120 60 10
2.3 Electrical Specifications
For US customers:
120V 60Hz pure sinewave inverter
Minimum power of 2kW per product
If operating from a generator a pure sinewave inverter is required.
2.3.1 Alternate Electrical Specifications
2.4 Component Specifications

19
D = Drain F = Fill L = Litre
2 SPECIFICATIONS
DD60*9 Des/Int Australia/New Zealand Wash Profiles
Wash Profile
511797 EE DD609 AA 1_0_140
Incoming @ 20°C
D F Pre
Wash
DF DF Post
Rinse 1
D F Post
Rinse 2
D F Final Rinse D Pause
(Vented)
Dry D Time
(min)
Time
Vented
(min)
Water
(L)
Fan
Run on
(min)
Heavy Time (min) 1 1 31 3 1 3 1 20 3 1 22 3 35 15 1 130 165 9.8 20
@2400-2700rpm Temp (°C) 60 60
Fill (L)
2.7
2.3
2.1
Heavy Extra Dry Time (min) 1 1 28 3 1 3 1 20 3 1 30 3 41 40 1 160 201 9.8 20
@2400-2700rpm Temp (°C) 60 70
Fill (L)
2.7
2.3
2.1
Heavy Quick Time (min) 1 1 24 3 1 3 1 10 3 1 25 3 35 0 1 101 136 10.2 20
@2400-2700rpm Temp (°C) 60 60
Fill (L)
2.7
2.5
2.3
Heavy Santise Time (min) 1 1 3 1 15 3 1 10 3 1 25 3 41 20 1 145 186 11.3 20
@2800rpm Temp (°C) 65 70
Fill (L)
0.5
2.7
2.7
2.7
Medium Time (min) 1 1 16 3 1 3 1 20 3 1 25 3 35 15 1 115 150 8.6 20
@2400rpm Temp (°C) 40 60
Fill (L)
2.3
2.1
2.1
Medium Extra Dry Time (min) 1 1 16 3 1 3 1 20 3 1 30 3 40 40 1 145 185 8.6 20
@2400rpm Temp (°C) 40 68
Fill (L)
2.3
2.1
2.1
Medium Quick Time (min) 1 1 11 3 1 3 1 10 3 1 26 3 35 0 1 86 121 9.0 20
@2400rpm Temp (°C) 40 60
Fill (L)
2.3
2.5
2.1
Medium Santise Time (min) 1 1 3 1 25 3 1 25 3 41 20 1 131 172 9.1 20
@2800rpm Temp (°C) 65 70°C
Fill (L)
2.7
0.5
0.5
2.7
2.7
Eco Time (min) 1 1 3 1 30 3 1 15 3 0 70 1 163 6.85 30
@2200rpm Temp (°C) 41
Fill (L)
0.9
1.9
1.9
Vented Eco Time (min) 1 1 3 1 30 3 1 15 3 0 70 1 166 6.85 30
@2200rpm Temp (°C) 44
Fill (L)
0.9
1.9
1.9
Fast Time (min) 1 1 1 1 4 1 1 15 2 29 0 1 46 75 7.3 20
@2400rpm Temp (°C) 50
Fill (L)
0.9
2.1
2.0
Fast Extra Dry Time (min) 1 1 1 1 4 1 1 19 2 35 15 1 65 100 7.3 20
@2400rpm Temp (°C) 60
Fill (L)
0.9
2.1
2.0
Delicate Time (min) 1 1 3 1 30 3 1 21 3 29 15 1 110 139 7.4 20
@2300rpm Temp (°C) 50
Fill (L)
0.9
2.1
2.1
Delicate Extra Dry Time (min) 1 1 3 1 30 3 1 26 3 32 40 1 140 172 7.4 20
@2300rpm Temp (°C) 55
Fill (L)
0.9
2.1
2.1
Delicate Quick Time (min) 1 1 3 1 20 3 1 22 3 29 0 1 86 115 7.8 20
@2300rpm Temp (°C) 50
Fill (L)
0.9
2.3
2.3
Rinse Time (min) 1 1 3 15 2.5
@2500rpm Temp (°C)
Fill (L)
Aug 17
2.3
2.7
2.7
2.1 2.1 2.1
50 57 70 21 50 21 21 50 47 65 24 65
Wash Cycle Main Wash
24 65 24 65
2.7 2.7 2.5
30 43
2.3
34 43 18 42 30 43
2.3
10 30 43 18 42
2.15
2.3 2.3
37 40
2.15
511797 EE DD609 AA 1_0_140 - Des_Int.xlsx
2.5.1 AA Market
2.5 Wash Profiles