Fisher-Price B8865 User manual

B8865
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
www.fisher-price.co.uk

2
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over. Use
only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lb).
• Never use toy bar as a handle.
• Never use as a carrier or lift while
child is seated.
WARNING
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
• Please read these instructions before assembly and use of this product.
• Adult assembly is required.
• Tools required for assembly: Phillips screwdriver (not included).
• Requires one “D” (LR20) alkaline battery (not included) and three
“AA” (LR6) alkaline batteries (not included) for operation.
• Product features and decorations may vary.
Consumer Information
The pad is machine washable. Wash the pad separately in cold
water on the gentle cycle. Do not use bleach. Tumble dry separately
on low heat and remove promptly. The frame and toy bar can be
wiped clean using a mild cleaning solution and a damp cloth.
Do not immerse the soothing unit or toy bar.
Care
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA B8865a-0726

3
Right Base Wire
Pad
Seat Back Tube
Left Base Wire
2 Retainers
Footrest with Soothing Unit
Base Tube
Note: Tighten or loosen all screws with a Phillips screwdriver.
Do not over-tighten the screws.
IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.
#8 x 2,2 cm Screw – 2
(Shown Actual Size)
Toy Bar
Parts
This package contains small parts in its unassembled state. Adult assembly is required.
CAUTION

4
1,5V
“D” (LR20)
+–
1,5V x 3
“AA” (LR6)
+–
• Loosen the screws in the battery compartment doors. Remove the
battery compartment doors.
• Insert one “D” (LR20) alkaline battery.
• Insert three “AA” (LR6) alkaline batteries.
• Replace the battery compartment door. Tighten the screws.
Hint: We recommend using alkaline batteries for longer battery life.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the mode/power off and then back on.
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
Battery Installation Battery Safety Information
In exceptional circumstances, batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type, as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.

5
1
IMPORTANT! Before assembly and each use, inspect this product for
damaged hardware, loose joints, missing parts or sharp edges. DO NOT use
if any parts are missing or broken. Contact Fisher-Price®for replacement
parts and instructions if needed. Never substitute parts.
Base Tube
Left Base Wire
Right Base Wire
Base WireColoured Dot
Base Tube
• Place the base tube on a flat surface as shown.
• Position the left and right base wires as shown. Note the locations
of the coloured dots on the left and right base wires.
• Fit the left base wire into the base tube.
• Fit the right base wire into the base tube.
• Make sure both coloured dots on the base wires are visible
through the holes in base tube.
BACK VIEW
Assembly
Soothing Unit Footrest Buttons Up
Tabs
Flex Base Wires Inward
• Position the footrest so that the soothing unit buttons are upright.
• While flexing the base wires toward each other, hook the footrest
onto the ends of the base wires.
• Slide the footrest down completely to the tabs on the base wires.
2
Base Wire
Base Wire
Seat Back Tube
Retainers
• Position the seat back tube above the base assembly. The seat
back tube should bend backward.
• Fit the seat back tube completely onto the base wires.
• Fit a retainer (rounded side inward) to one end of the seat back tube.
• Insert a #8 x 2,2 cm screw through the outside hole in the seat
back tube and into the retainer.
• While holding the retainer in place, tighten the screw with
a Phillips screwdriver. Do not overtighten.
• Repeat this procedure to secure the other side of the seat back
tube to the base assembly using the remaining retainer and
#8 x 2,2 cm screw.
3

6
Assembly
Pull Up
• Pull up on the seat back tube to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
it correctly. Remove the screws and retainers. Re-read and repeat
Assembly step 3.
• Fit the pad upper pocket onto the seat back tube.
• Fit the pad lower pocket onto the footrest.
4
5
• Fit the toy bar ends into the sockets in the footrest.
Hint: The square end of the toy bar fits into the square socket and
the circular end of the toy bar fits into the circular socket.
• Make sure the toy bar latches are secure. The small tabs on the
sockets should be visible in the opening in the latches.
Tab
Latch
Remove the Toy Bar
• Pull the ends of the latches and lift the toy bar.
Latch
6
7

7
Setup and Use
Calming Vibrations
• Make sure your child is properly secured in the seat.
• To turn vibrations on, slide the power switch on the soothing unit
to the on position .
• To turn vibrations off, slide the power switch on the soothing unit
to the off position .
IMPORTANT! If vibrations become faint, or if there are no vibrations,
remove the “D” (LR20) battery from the soothing unit and dispose
of it properly. Replace the battery with a new “D” (LR20)
alkaline battery.
1
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over. Use
only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Always use restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 kg/20 lb).
• Never use toy bar as a handle.
• Never use as a carrier or lift while
child is seated.
WARNING
Securing Your Child
• If the toy bar is attached, remove it before placing your child
in the seat. Place your child in the seat. Position the restraint
between your child’s legs.
• Fasten both restraint belts to the buckles on each side of the
restraint pad. Make sure you hear a “click” on both sides.
• Check to be sure the restraint is securely attached by pulling it
away from your child. The restraint should remain attached.
• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to the next section for instructions
to tighten the waist belts.
• Attach the toy bar, if desired (see Assembly step 6).
Restraint Belt
Restraint Pad Buckle
2
To tighten the belts:
•
Feed the anchored end of the belt up through the buckle to form
a loop A.
• Pull the free end of the belt B.
• Repeat this procedure to tighten the other belt.
TIGHTEN LOOSEN
To loosen the belts:
• Feed the free end of the belt up through the buckle to form
a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle.
• Pull the anchored end of the belt to shorten the free end of the
belt B.
• Repeat this procedure to loosen the other belt.
Note: After adjusting the belts to fit your child, make sure you pull
on them to be sure they are securely fastened.
Free End
Anchored End Buckle
Free End
Anchored End Buckle
3

8
Baby-activated (Short Tunes)
• Slide the mode switch to for baby activated mode.
• When baby kicks a footrest button, baby is rewarded with a short
tune or sound effects and dancing lights.
Long-Playing Music
• Slide the mode switch to for parent activated mode. Baby enjoys
up to 10 minutes of music along with a light show.
Off
• Slide the mode switch off to turn off music, sounds and lights.
Volume
• Slide the volume switch to for low volume; for high volume.
IMPORTANT! If lights become dim or sound becomes faint,
remove the “AA” (LR6) batteries from the soothing unit and dispose
of properly. Replace the batteries with three, new “AA” (LR6)
alkaline batteries.
Volume Switch
Mode Switch
Footrest Buttons
Footrest Buttons
(Underneath Pad)
(Underneath Pad)
Setup and Use
Teethers
• The teethers are removable from the toy bar for baby’s use.
Simply twist the ends of each teether slightly to remove them
from the centre toy.
5
4