Fisher-Price V6908 User manual

V6908
V6908
www.fisher-price.co.uk
IMPORTANT! KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

2
IMPORTANT! Place the high chair on a level, stable surface
away from electrical flexes. Be sure to keep electrical flexes out
of child's reach.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.
• Tool needed for assembly: Phillips screwdriver (not included).
• Maximum weight: 23 kg (50 lb)
• Before use, thoroughly wash all parts that may contact food.
• The base tray is not dishwasher safe.
• The food tray is not microwave safe.
• Product features and decorations may vary from
photographs.
IMPORTANT! Before assembly and each use, inspect this
product for damaged hardware, loose joints, missing parts or
sharp edges. DO NOT use if any parts are missing or broken.
Contact Fisher-Price®for replacement parts and instructions if
needed. Never substitute parts.
This package contains small parts in
its unassembled state. Adult assembly
is required.
CAUTION
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World
Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Consumer Information
Prevent serious injury or death
from falls or sliding out:
• The child should at all times wear
a safety harness correctly tted and
adjusted. The tray is not designed to
hold the child in the chair.
• It is recommended that only children
capable of sitting upright unassisted
use the high chair in the
upright position.
• NEVER leave child unattended.
• Do not use the high chair unless all
components are correctly tted
and adjusted.
• NEVER use near steps.
Prevent injury from burns: Do not
place this high chair near open res or
any hot surfaces.
WARNING

3
Pad Seat Back
Assembled Parts
Note: Tighten or loosen all screws with a Phillips screwdriver. Do not over-tighten the screws.
Shown Actual Size
#8-16 x 1,9 cm Screw – 6 #10 x 1,9 cm Washer Head Screw – 2
Base2 Armrests
Base Tray Food Tray
2 Frame Covers
Seat Bottom
Frame

4
FRONT VIEW
• Position the frame so that the wider end is down.
• Slide the ends of the frame into the sockets on the base. Push to
“snap” in place. Pull up on the frame to be sure it’s secure in
the base.
Hint: The frame is designed to assemble to the base one way.
If you can remove the frame from the base, turn it around and
try again!
• Place the base on a flat surface.
Hint: You may need to rotate the base sockets so they are
upright, as shown.
• Carefully turn the seat bottom over.
• Insert four #8-16 x 1,9 cm screws into the seat bottom and tighten.
Assembly
2
1
4
Base
Base
Frame
• Fit an armrest onto the seat bottom.
Hint: The armrests are designed to fit to the seat bottom one
way. If it does not seem to fit, try the other armrest.
• Repeat this procedure to assemble the other armrest.
3
Armrest
Seat Bottom
#8-16 x 1,9 cm Screws
BACK VIEW
• Fit the seat bottom assembly onto the frame.
• Slide the seat bottom assembly down until you hear a "click".
5

5
Seat Back
Tab
Tab
Assembly
• Insert a #10 x 1,9 cm washer head screw into the hole in
each side of the seat back. Tighten both screws.
7
#10 x 1,9 cm
Washer Head Screws
• Fit the tabs on the seat back into the openings in each side of
the seat bottom.
6• Fit the frame covers into each frame tube.
Frame Covers
8BACK VIEW
#8-16 x 1,9 cm Screws
• To secure the frame covers, insert a #8-16 x 1,9 cm screw into
the hole in each frame tube and tighten.
9

6
Assembly
Armrests
• Fit the side slots in the pad onto the armrests.
10
Pad
FRONT VIEW
• Lift the lower portion of the pad. Insert the crotch belt up
through the largest and lowest slot in the pad. Make sure the
belt is not twisted.
11
Crotch Belt
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2010 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN MEXICO V6908pr-0726
12
• Insert both elastic loops on the pad through the holes in the
footrest area of the seat bottom.
• From the back and bottom of the seat, hook the elastic loops
to the tabs on the seat bottom.
Tabs
Tabs
Elastic Loops
Elastic Loops
Elastic Loops
Elastic Loops
BACK VIEW
BACK VIEW

7
Assembly
Waist Belts
13
• Fold the top of the pad down and insert the waist belts through
the lowest set of slots in the pad. Make sure the belts are
not twisted.
14
• Insert the shoulder belts through the slots in the pad.
-Use the lower shoulder belt slots for a smaller baby.
-Use the upper should belt slots for a larger baby.
Smaller Baby Larger Baby
Lower Shoulder Belt Slots Upper Shoulder Belt Slots
To change shoulder belt slots:
• From the back of the high chair, pull each shoulder belt
through the slots in pad and seat back.
• Then, insert each shoulder belt back through the desired
shoulder belt slots in the seat back and pad.
15 BACK VIEW Shoulder Belts
16
• Fit the top of the pad over the seat back.

8
Assembly
17
• Hook the elastic loops on each side of the pad onto the tabs in
the seat back.
Elastic Loops
Tabs
Tabs
18
Slots
Slots
Hooks
Hooks
• Fit both hooks on each side of the pad into the slots in the seat
back (near the armrests).
Secure Child
Prevent serious injury or death
from falls or sliding out:
• The child should at all times wear
a safety harness correctly tted and
adjusted. The tray is not designed to
hold the child in the chair.
• NEVER leave child unattended.
• Do not use the high chair unless all
components are correctly tted
and adjusted.
• NEVER use near steps.
Prevent injury from burns: Do not
place this high chair near open res or
any hot surfaces.
WARNING

9
Secure Child
• Place your child in the seat. Position the crotch belt between your
child’s legs.
• Fit the end of each waist belt through the end of each shoulder belt.
• Fasten both waist/shoulder belts to each side of the crotch
belt. Make sure you hear a "click" on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
• Tighten each waist belt and shoulder belt so that the restraint
system is snug against your child. Please refer to the next section
for instructions to tighten the waist belts and shoulder belts.
Waist Belts
Crotch Belt
1
To tighten the waist/shoulder belts:
• Lift the tabs on the seat back.
• Pull the free end of the restraint belts that you would like
to tighten.
• Lower the tabs on the seat back to secure the restraint belts
in place.
2
TIGHTEN
To loosen the waist/shoulder belts:
• Lift the tabs on the seat back.
• From the front of the seat, pull the restraint belts that you would
like to loosen.
• Lower the tabs on the seat back to secure the restraint belts
in place.
3
LOOSEN
Shoulder Belts
To change shoulder belt slots:
• Remove the end of each shoulder belt from each waist
belt buckle.
• From the back of the high chair, pull each shoulder belt
through the slots in pad and seat back.
• Then, insert each shoulder belt back through the desired
shoulder belt slots in the seat back and pad.
4

10
Using the Trays
Prevent serious injury or death from
falls or sliding out:
• The child should at all times wear a safety
harness correctly fitted and adjusted. The
tray is not designed to hold the child in
the chair.
• Do not use the high chair unless all
components are correctly fitted
and adjusted.
WARNING
• Fit the base tray onto the seat armrests. Push down until the
base tray “snaps” in place.
Hint: Before use, thoroughly wash all parts (the trays) that may
contact food. The base tray is not dishwasher safe.
5
Base Tray
Armrests
• While pushing the release bar on the front of the base tray,
adjust the base tray forward or backward.
• While pushing the release bar on the front of the base tray,
pull the base tray towards you and remove.
PUSH
PUSH
6
7