Fisher-Price Classical Chorus B0772 User manual

D
i
s
c
o
v
e
r
w
h
a
t
’
s
p
o
s
s
i
b
l
e
™
…
w
w
w
.
f
i
s
h
e
r
-
p
r
i
c
e
.
c
o
m
Bouncer
Classical Chorus™
Model Number: B0772
Please keep this instruction sheet for future reference,
as it contains important information.
Adult assembly is required. Tool required for assembly:
Phillips Screwdriver (not included).
Requires three “C” (LR14) alkaline batteries (not included).

2
Warning and Caution
To prevent serious injury and/or falls:
• Never use on any elevated surface,
since child’s movement may cause
bouncer to slide or tip over.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use as a car seat.
• Never use with a child able to sit
up unassisted.
WARNING
This package contains small parts
in its unassembled state.
Adult assembly is required.
CAUTION

Parts
3
Toybar
Pad
Seatback
Tube
Retainer
Retainer
Soothing Unit
Right Base Wire
Left Base Wire
Footrest
Base Tube
#8 x 3/4" Screw - 2
Shown Actual Size

Battery Installation
4
1.5V x 3
“C” (LR14)
SHOWN ACTUAL SIZE
Battery Compartment Door
Battery Tips
• Do not mix old and new batteries.
• Do not mix different types of batteries: alkaline, standard (carbon-zinc) or
rechargeable (nickel-cadmium).
• Remove the batteries during long periods of non-use. Always remove
exhausted batteries from the product. Battery leakage and corrosion
can damage the product. Dispose of the batteries safely.
• Do not dispose of batteries in a fire.The batteries may explode or leak.
• Never short circuit the battery terminals.
• Non-rechargeable batteries are not to be recharged.
• Only batteries of the same or equivalent type as recommended in the
“Battery Installation” instructions are to be used.
• If removable rechargeable batteries are used, they are only to be charged
under adult supervision.
• Rechargeable batteries are to be removed from the product before they
are charged.
• If you use a battery charger, it should be examined regularly for damage to
the cord, plug, enclosure and other parts. Do not use a damaged battery
charger until it has been properly repaired.
• Loosen the screw in the soothing unit battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
• Insert three “C” (LR14) alkaline batteries, as indicated inside the
battery compartment.
• Replace the battery compartment door and tighten the screw with a
Phillips screwdriver. Do not over-tighten.
Hint: We recommend the use of alkaline batteries for longest battery life.

• Place the base tube on a flat surface
as shown.
• Position the left and right base wires as
shown. Note the location of the colored
tabs on the left and right base wires.
• Fit the left base wire into the base tube.
• Fit the right base wire into the base tube.
•Make sure both colored tabs on the base wires are visible through the
holes in the base tube.
1
Base Tube
Colored Tab
Back View
Base Wire
Assembly
Base Tube
Left Base Wire
Colored Tabs
Right Base Wire
5
2
Soothing Unit
Clip Screw
Footrest
Soothing Unit
• Loosen the screw in the soothing unit clip with a Phillips screwdriver.
• Slide the soothing unit onto the footrest, as shown. Make sure the footrest
is completely in the grooves around the sides and back end of the
soothing unit.
• Tighten the screw in the soothing unit clip with a Phillips screwdriver.
Do not over-tighten.

• Position the footrest so that the soothing unit is upright.
• While flexing the base wires toward each other, hook the footrest onto the
ends of the base wires.
• Push the footrest down completely to the tabs on the base wires.
Assembly
Tab Tab
Footrest with Soothing Unit
Flex Base
Wires Inward
3
6
4
Seat Back Tube
Base Wire
Base Wire
• Fit the seat back tube completely onto the base wires.

• Fit a retainer to the outside of the seat
back tube, as shown. Make sure the
socket in the retainer is upright.
• Insert a screw through the hole in the
seat back tube, base wire and into the
inside of the retainer.
• Tighten the screw with a Phillips screw-
driver. Do not over-tighten.
• Repeat this procedure to assemble the
other retainer to the other side of the
seat back tube.
• Pull up on the seat back tube to be sure it is secure. If you can remove
either end of the seat back tube, you have not assembled the retainers
correctly. Remove the screws, re-read and repeat Assembly steps 4 and 5.
Assembly
5
7
Seat Back Tube
Retainer
Socket
Up
Retainer
Socket
Up
PULL UP

Assembly
Seat Back
Tube
Pad
Footrest
Soothing
Unit
6
8


• Position the pad above the frame with the blanket toward the soothing unit.
• Fit the upper pocket on the back of the pad onto the seat back tube .
• Lift the footrest. Fit the lower pocket on the back of the pad onto the
footrest . Lower the footrest.

• Fit the toy bar plugs into each retainer socket.
• The toy bar is removable. Simply pull to remove.
Assembly
7
9
Plugs
Toy Bar
Retainer
Socket
Retainer
Socket

10
Set-Up & Use
To prevent serious injury and/or falls:
• Never use on any elevated surface,
since child’s movement may cause
bouncer to slide or tip over.
• Never use as a carrier or lift while child
is seated.
• Always use the restraint system.
• Never leave child unattended.
• Never use with a child able to sit
up unassisted.
WARNING
Securing Your Child
• If the toy bar is attached, remove it before placing your child in the seat.
• Place your child in the seat. Position the restraint between your child’s legs.
• Fasten both belts to the buckles on each side of the restraint. Make sure
you hear a “click” on both sides.
• Check to be sure the restraint is securely attached by pulling it away from
your child. The restraint should remain attached.
• Attach the toy bar, if desired (see Assembly Step 7).
1
Belt
Buckle
Restraint