Fisher-Price X3844 User manual

www.fisher-price.co.uk
X3844
X3844
IMPORTANT! KEEP FOR FUTURE REFERENCE.

2
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child’s movement may cause
product to slide or tip over. Use only on
a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since product
can tip over and cause suffocation in
soft surfaces.
• Never use as a carrier or lift while child is
seated. Never use toy bar to carry product.
• Always use the restraint system.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Never leave child unattended.
• Do not use product once child can sit unaided.
WARNING
Consumer Information
IMPORTANT! Please keep this instruction sheet for future reference,
as it contains important information.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tool needed for assembly: Phillips
Screwdriver (not included).
• Requires one "D" (LR20) alkaline battery for soothing unit
operation. Requires one "AAA" (LR03) alkaline battery for toy bar
operation. Batteries not included.
• Weight limit: 9 kg (20 lbs)
• This product does not replace a cot or bed. Should the child need
to sleep, place the child in a suitable cot or bed.
• Product features and decorations may vary from photographs.
This package contains small parts in an
unassembled state. Adult assembly is required.
CAUTION
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Mattel Europa, B.V., Gondel 1, 1186 MJ Amstelveen, Nederland.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked
Bag #870, Richmond, Victoria 3121 Australia. Consumer Advisory
Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance
Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe,
Persiaran Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Fisher Price, Inc., a subsidiary of Mattel, Inc., East Aurora, NY 14052 U.S.A.
©2011 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA X3844pr-0726
B
C
To remove the pad:
• Pull to remove the pad from around the retainers and the soothing
unit A.
• Remove the bottom pocket of the pad from the footrest B.
• Lift to remove the pad C.
• To replace the pad, refer to Assembly steps 7 - 9.
A
A
Care
• The pad and head support are machine washable. Wash them
separately in cold water on the gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• The frame, toy bar and toys may be wiped clean using a mild
cleaning solution and damp cloth. Do not immerse the toy bar.
Do not use bleach. Do not use harsh or abrasive cleaners.
Rinse clean with water to remove residue.

3
Parts
2 Feet
Left Base Wire
Pad
Head Support
2 Toys
Seat Back Tube
Footrest
Right Base Wire
Base Tube
IMPORTANT! Please remove all parts from the package and identify them before assembly. Some parts may be packed in the pad.
Note: Screws shown actual size. Tighten or loosen all screws
with a Phillips screwdriver. Do not over-tighten the screws.
2 Retainers
Toy Bar
M5 x 20 mm Screw – 2 #8 x 2,2 cm Screw – 2

4
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel for
replacement parts and instructions if needed. Never substitute parts.
• Place the base tube on a flat surface.
• Position the left and right base wires as shown.
• Fit the left base wire and right base wire into the base tube.
Right Base Wire
Base Tube
Left Base Wire
1
Assembly
• Insert an M5 x 20 mm screw through each foot and tighten.
3
Non-skid Surface
2
• Position the feet so the non-skid surface is down.
• Fit the feet on the base tube, as shown.
• Position the footrest so that the soothing unit is upright.
• Fit the footrest onto the ends of the base wires.
Base Wires
Footrest
4
• Fit the seat back tube onto the ends of the base wire.
• Push the seat back tube to be sure it is completely on the
base wires.
Seat Back Tube
5

5
• Fit a retainer to the inside of each end of the seat back tube.
• Insert #8 x 2,2 cm screw into the outside hole in the ends of the
seat back tube and tighten.
• Pull the seat back tube up to be sure it is secure. If you can
remove either end of the seat back tube, you have not assembled
the retainers correctly. Remove the screws, re-read and repeat.
Assembly steps 5 and 6.
6
Retainers
Assembly
• Position the pad above the frame.
• Fit the upper pocket on the back of the pad onto the seat back tube.
Pad Seat Back Pocket
7
Pad Lower Pocket
• Fit the lower pocket on the back of the pad onto the footrest.
8
• Fit the toy bar retainer through the side opening in the pad.
• Fit the edges of the soothing unit through the large opening in the
front of the pad.
9
Soothing Unit
Toy Bar Retainer
• Press the head support strap to the fastener on the back of the pad.
Hint: You can move the head support up or down for your
baby’s comfort.
10
Head Support

6
Assembly
• Clip the removable toys to the hanging toys on the toy bar.
12
Toys
Toy Bar
Latch
Toy Bar Retainer
• Insert and “snap” the toy bar into the toy bar retainer.
• Press the latch the end of the toy bar to the tab on the socket.
Hint: The toy bar is removable. Pull the end of the latch and lift the
toy bar.
11
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
+
–1,5V
“D” (LR20)
1,5V
“AAA” (LR03)
• Pull to remove the pad from around the toy bar retainer and the
soothing unit A.
• Remove the pad bottom pocket from the footrest B.
1
B
A
A
Soothing Unit
• Loosen the screw in the battery compartment door. Remove the
battery compartment door.
• Insert one “D” (LR20) alkaline battery into the battery compartment.
• Replace the battery compartment door and tighten the screw.
• Fit the toy bar retainer through the side opening in the pad.
• Pull and fit the pad seat bottom pocket around the soothing unit
and footrest.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power switch off and then back on.
2
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities.

7
3
Toy Bar
• Loosen the screw in the battery compartment door with
a Phillips screwdriver. Remove the battery compartment door.
• Insert one "AAA" (LR03) alkaline battery into the
battery compartment.
• Replace the battery compartment door and tighten the screw.
• If the toy bar begins to operate erratically, you may need to reset
the electronics. Remove the battery and reinstall.
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.
Battery Safety Information
Battery Installation
To prevent serious injury or death:
• Fall Hazard - Never use on any elevated
surface, since child’s movement may cause
product to slide or tip over. Use only on
a floor.
• Suffocation Hazard - Never use on a soft
surface (bed, sofa, cushion) since product
can tip over and cause suffocation in
soft surfaces.
• Never use as a carrier or lift while child is
seated. Never use toy bar to carry product.
• Always use the restraint system.
• This product is not intended to replace a cot
or bed for prolonged periods of sleep.
• Never leave child unattended.
• Do not use product once child can sit unaided.
WARNING
Restraint Belts
Securing Your Infant
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the restraint belts to the restraint pad. Make sure you hear
a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Restraint Pad
1
Setup and Use

8
Setup and Use
• Tighten each waist belt so that the restraint system is snug against
your child. Please refer to the next section for instructions to
tighten the waist belts.
2
Restraint System
B
A
A
B
To tighten the restraint belts:
• Feed the anchored end of the restraint belt up through the buckle
to form a loop A. Pull the free end of the restraint belt B.
To loosen the restraint belts:
• Feed the free end of the restraint belt up through the buckle to
form a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the restraint belt to
shorten the free end of the restraint belt B.
Anchored End Anchored End
TIGHTEN LOOSEN
Free End Free End
3
e
m is snug against
s
tructions to
Soothing Unit and Toy Bar
Power Switch
PULL
• Make sure your child is properly secured in the seat.
• Slide the power switch to: Vibrations or Off.
IMPORTANT! Low battery power causes this product to operate
erratically: no vibrations and the product may not turn off. Remove
and discard the battery and replace with a new “D” (LR20)
alkaline battery.
• Pull the toy for sounds.