Fisher-Price J7814 User manual

www.fisher-price.com/uk
J7814
1
Infant
2
Older Baby
3
Note: Use the hammock (con-
nected to all four corners of the
bathtub) only for a baby that
weighs up to 4,54 kg (10 lbs).
Newborn
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.
WARNING

• Babies have DROWNED while using
infant bathtubs. Since babies can
drown in as little as one 2,5 cm (1")
of water, ALWAYS bathe baby using
as little water as necessary.
• Never place this product in water in
a larger bathtub.
•
ALWAYS keep child within adult’s reach.
• DO NOT allow other children to
substitute for an adult.
• DO NOT carry baby in this product.
• ALWAYS test water temperature for
comfort on wrist before placing baby
in tub.
• Before use, ALWAYS test tub for
secure fit in sink or bath. For domestic
use only.
WARNING
2
Consumer Information
Consumer Information
Parts
Parts
3 Toys
Bathtub
Hammock
Base
#8 x 2,5 cm (1”) Screw – 2
Fastener Shown Actual Size
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required.Tool needed for assembly:
Phillips Screwdriver (not included).
• Water toys sometimes get messy. Protect play surfaces
before use.
• Overfilling the bathtub may cause it to leak.
• After each use, drain and rinse all items.
• Before storing, drain, clean, rinse and dry all items.
• The hammock is surface wash only with a mild cleaning
solution
and damp cloth. Do not use bleach. Rinse the
hammock thoroughly.
Squeeze excess water from the
hammock and line dry.
• Product features and decoration may vary from photos.
THIS PRODUCT IS NOT
A SAFETY DEVICE.
CAUTION
This product contains small parts
in its unassembled state. Adult
assembly is required.
Warning and Caution
Warning and Caution

3
Set-up the Aquarium Bath Center for use with a 1Newborn
(up to 4,54 kg - 10 lbs), 2Infant or 3Older Baby.
One - Time Assembly
One - Time Assembly
3 Stages of Use
3 Stages of Use
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp edges.
DO NOT use if any parts are missing or broken. Contact Mattel
for
replacement parts and instructions if needed. Never
substitute parts.
• Turn the bathtub upside down on a flat surface.
• Fit the base to the bathtub.
•
I nsert two screws into the base and tighten with a Phillips
screwdriver. Do not over-tighten.
Bathtub
Base
1
3
2

4
Newborn
Newborn
• Fit the clips on the headrest end of the hammock to the nar-
row end of the bathtub. Fit the clips on the other end of the
hammock to the wide end of the bathtub.
• Tighten the hammock fit as much as possible. Pull the
free end of the belts.
• Fit the bathtub to the sink, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
Fill the bathtub with as little water as possible to
bathe baby. Test water temperature.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby on the hammock.
Hint: To loosen hammock fit, lift the buckle.
Clips
Clips Headrest
Wide End
Narrow End
1
Note: Newborn stage (of use) is only intended for a baby who
weighs up to 4,54 kg (10 lbs).
TIGHTEN LOOSEN

Clips
Headrest
Narrow End
• Fit the clips on the headrest end of the hammock to the narrow
end of the bathtub.
• Lay the bottom of the hammock in the bathtub.
• Fit the bathtub to the sink, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
•
Fill the bathtub with as little water as possible to bathe baby.
Test water temperature.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby on the hammock.
Infant
Infant
2
• Place the bathtub in a larger bathtub, or place on a flat surface.
• Fit the plug into the hole in the bottom of the bathtub.
• Fill the bathtub with as little water as possible to bathe
baby.Test water temperature.
• Plug the toy into the side slot in the bathtub.
• Carefully place baby in the bathtub.
5
Older Baby
Older Baby
3

www.service.mattel.com/uk
Telephone [phone]
Great Britain: Mattel UK Ltd., Vanwall Business Park, Maidenhead SL6 4UB.
Australia: Mattel Australia Pty. Ltd., 658 Church Street, Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower, World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Questions?
If you are missing parts or need assistance, we can help!
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A. PRINTED IN CHINA
©2005 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc. J7814pr-0726