Fisher-Price P7539 User manual

www.fisher-price.co.uk
P7539
WARNING
IMPORTANT! KEEP INSTRUCTIONS
FOR FUTURE REFERENCE.

2
Consumer Information
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over. Use
only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Never leave child unattended.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 Kg/20 lbs).
WARNING
IMPORTANT! Please keep these instructions for future reference.
• Please read these instructions before assembly and use of
this product.
• Adult assembly is required. Tools needed for assembly: Allen
Wrench (included) and Phillips screwdriver (not included).
• Requires three “C” (LR14) alkaline batteries (not included) for
soother operation.
• Product features and decoration may vary from photographs.
Fasteners are shown actual size.
Fasteners
3.5mm x 32mm screw – 2
M6 - 1 x 15mm screw – 8
8mm x 27mm screw – 2
Great Britain: Vanwall Business Park, Maidenhead SL6 4UB.
Helpline: 01628 500303. www.service.mattel.com/uk.
Australia: Mattel Australia Pty. Ltd., 658 Church Street,
Locked Bag #870, Richmond, Victoria 3121 Australia.
Consumer Advisory Service 1300 135 312.
New Zealand: 16-18 William Pickering Drive, Albany 1331, Auckland.
Asia: Mattel East Asia Ltd, Room 1106, South Tower,
World Finance Centre, Harbour City, Tsimshatsui, HK, China.
Malaysia: Diimport & Diedarkan Oleh: Mattel SEA Ptd Ltd.
(993532-P) Lot 13.5, 13th Floor, Menara Lien Hoe, Persiaran
Tropicana Golf Country Resort, 47410 PJ. Tel: [phone].
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2009 Mattel, Inc. All Rights Reserved. ® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTED IN CHINA P7539pr-0726

3
Parts
This package contains small parts in
its unassembled state. Adult assembly
is required.
IMPORTANT! Please remove all parts from the package and identify
them before assembly. Some parts may be packed in the pad.
CAUTION
Crossbar
Soothing UnitHead Snuggler
Seat Assembly
Pad
Allen Wrench
Assembly
• Lay the seat assembly face down on a flat surface.
• Locate the foot tube that is attached to the liner. Line up the
holes in each end of the foot tube with the holes in the side rails.
• Insert two M6-1 x 15mm screws through the holes on each end
of the foot tube and into each side rail. Tighten each screw with
the Allen wrench.
IMPORTANT! Before assembly and each use, inspect this product
for damaged hardware, loose joints, missing parts or sharp
edges. DO NOT use if any parts are missing or broken. Contact
Fisher-Price®for replacement parts and instructions if needed.
Never substitute parts.
1
Foot Tube
• Turn the assembly around. Locate the head tube that is attached
to the liner. Line up the holes in each end of the head tube with
the holes in the side rails.
• Insert an M6-1 x 15mm screw through the hole on each end of
the head tube and into each side rail. Tighten the screws with the
Allen wrench.
2
Seat Assembly
Head Tube

4
• Insert two 8mm x 27mm screws into the outside holes in the
side rails and tighten with the Allen wrench.
4
Outside Holes
• Turn the seat assembly upright.
• At an angle, first insert one end of the crossbar into the groove
in the side rail, as shown.
• Then, insert the other end of the crossbar into the groove in the
other side rail.
• Insert two M6-1 x 15mm screws into the inside holes in each
side rail and tighten with the Allen wrench.
Hint: You may need to push both side rails together to align the
holes in each end of the crossbar and the side rails.
3
Crossbar
Inside Holes
Assembly
• Fit the soothing unit onto the foot tube, as shown.
• Insert two 3.5 mm x 32 mm screws into the foot tube.
Tighten the screws with the Allen wrench.
5
Soothing Unit
Foot Tube

5
Assembly
• Place the pad onto the seat.
• Insert the waist belts up through smaller slots in the pad.
Make sure the waist belts are not twisted. Fit the restraint pad up
through the larger slot in the pad.
• Fold the tabs on the top and bottom of the pad around the head
and foot areas and fasten.
• Fasten the head snuggler onto the strap on the seat.
6
Fasteners
Fasteners
Head Snuggler
Waist Straps
Restraint Pad
Battery Installation
Hint: We recommend using alkaline batteries for longer battery life.
• Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).
1,5V x 3
“C” (LR14)
• Locate the battery compartment on the top of the soothing unit.
• Loosen the screws in the battery compartment door. Lift to
remove the battery compartment door.
• Insert three “C” (LR14) alkaline batteries.
• Replace the battery compartment door and tighten the screws.
• If this product begins to operate erratically, you may need to reset
the electronics. Slide the power/mode switch off and then back on.
IMPORTANT! Low battery power could cause this product to
operate erratically: no vibrations/sound and the product may not
turn off. Remove and discard the batteries and replace them with
three new “C” (LR14) alkaline batteries.
Battery Safety Information
In exceptional circumstances, batteries may leak fluids that can
cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of this product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removeable, rechargeable batteries are used, they are only to be
charged under adult supervision.

6
• Place your child in the seat. Position the restraint pad between
your child’s legs.
• Fasten the waist belts to each side of the restraint pad.
Make sure you hear a “click” on both sides.
• Check to be sure the restraint system is securely attached by
pulling it away from your child. The restraint system should
remain attached.
Restraint Pad
Waist Belts
Securing Your ChildSetup and Use
To prevent serious injury or death:
• Fall Hazard - It is dangerous to use
this product on an elevated surface,
since child's movement may cause
the product to slide or tip over. Use
only on a oor.
• Suffocation Hazard - Never use on
a soft surface (bed, sofa, cushion)
since the product can tip over and
cause suffocation in soft surfaces.
• Never leave child unattended.
• Never use as a carrier or lift while
child is seated.
• Always use the restraint system.
• Not recommended for children who
can sit up by themselves (6 months
approximately, until 9 Kg/20 lbs).
WARNING
Anchored End Anchored End
Free End Free End
LOOSEN
TIGHTEN
To tighten the belts:
• Feed the anchored end of the waist belt up through the buckle to
form a loop A. Pull the free end of the waist belt B.
To loosen the belts:
• Feed the free end of the waist belt up through the buckle to form
a loop A. Enlarge the loop by pulling on the end of the loop
toward the buckle. Pull the anchored end of the restraint belt to
shorten the free end of the waist belt B.
• Tighten each waist belt so that the restraint system is snug
against your child. Please refer to the next section for instructions
to tighten the waist belt.
Restraint System

7
Infant Rocker or Stationary Seat
Infant Rocker
• While pulling the latches toward you, lower the crossbar until it
“clicks” into place.
Stationary Seat
• While pulling the latches toward you, lift the crossbar until it
“clicks” into place.

8
• Slide the power/mode switch to Music , Vibrations ,
Vibrations and Music or OFF .
Soothing Unit Care
• The pad and head snuggler are machine washable. Wash them
separately in cold water on gentle cycle. Do not use bleach.
Tumble dry separately on low heat and remove promptly.
• The frame and toy can be wiped clean using a mild cleaning
solution and a damp cloth. Do not use bleach. Do not use harsh
or abrasive cleaners. Do not immerse the frame.
To remove the pad:
• Lift the fasteners on the head and foot of the pad. Push the restraint
system back through the pad.
To replace the pad:
• Place the pad onto the seat.
• Fit the waist straps and restraint pad through the slots in the pad.
• Secure the fasteners on the head and foot of the pad.