Fisher-Price H7178 User manual

Product features and decorations may vary from the photo above.
H7178
www.fisher-price.com/uk
WARNING
IMPORTANT! PLEASE KEEP INSTRUCTIONS FOR FUTURE REFERENCE.

Important!
• This product is not intended to be used as a medical
monitor and its use should not replace adult supervision.
• Test sound reception of receiver before first-time use
and whenever you change location of transmitter.
• To prevent entanglement:
- Never place transmitter in a crib or playpen. Keep
transmitter and receiver out of baby’s reach.
- Never use extension cords with the AC adaptors.
• Never use transmitter or receiver near water (ie.: bathtub,
sink or wet basement, etc.).
• Always use transmitter and receiver where there is
adequate ventilation. To prevent overheating, keep
transmitter and receiver away from heat sources such
as radiators, heat registers, direct sunlight, stoves,
amplifiers, or other appliances which produce heat.
• Never attempt to modify this product.
• For proper setup and use, please read these instructions.
• Please keep this instruction sheet for future reference,
as it contains important information.
• Range: 122 meters (400 feet).
• Transmitter is electrically powered.
• Receiver is powered by the AC adaptor (included, plugs into
standard household outlets). Receiver also runs on battery
power (three LR6 (“AA”) alkaline batteries – not included).
• Requires one PR12 (or equivalent) light bulb (included).
• An adult must install the batteries (if used) and replace the
light bulb. Tool needed for battery installation and light bulb
replacement: Phillips screwdriver (not included).
WARNING
To prevent strangulation with
power cord, never place
transmitter within reach of child.
CAUTION
This product cannot replace
responsible adult supervision.
2

Receiver Battery Installation
(Optional) Battery Safety Information
• Locate battery compartment door on back of receiver.
• Loosen screw in battery compartment door with a Phillips
screwdriver. Lift to remove battery compartment door.
• Insert three LR6 ("AA") alkaline batteries into the
battery compartment.
• Replace battery compartment door and tighten screw.
Do not over-tighten.
Hint: We recommend using alkaline batteries for longer battery life.
Battery Compartment Door
In exceptional circumstances batteries may leak fluids that
can cause a chemical burn injury or ruin your product. To avoid
battery leakage:
• Do not mix old and new batteries or batteries of different types:
alkaline, standard (carbon-zinc) or rechargeable (nickel-cadmium).
• Insert batteries as indicated inside the battery compartment.
• Remove batteries during long periods of non-use. Always remove
exhausted batteries from the product. Dispose of batteries safely.
Do not dispose of product in a fire. The batteries inside may
explode or leak.
• Never short-circuit the battery terminals.
• Use only batteries of the same or equivalent type,
as recommended.
• Do not charge non-rechargeable batteries.
• Remove rechargeable batteries from the product before charging.
• If removable, rechargeable batteries are used, they are only to be
charged under adult supervision.
LR6 (AA)
1.5V x 3
3
•Protect the environment by not disposing of this product
with household waste (2002/96/EC). Check your local
authority for recycling advice and facilities (Europe only).

Testing Sound Reception
6
5
14
7
7
9
10
• Variable light display lights when sound is received by receiver:
- One or two dots light for shallow sounds.
- Three or more dots light for louder sounds.
• If you experience interference (buzzing or static, etc.) while using
one channel setting, switch both units to other channel. Selecting
a channel is usually a one time adjustment.
Hint: All four dots on receiver variable light display light:
- If you turn receiver power on before transmitter power. You will also hear
static noise. Turn volume down and turn transmitter power on.
- If the receiver is too far away from the transmitter. Move the receiver closer
to the transmitter.
- If loud sounds are transmitting.
Place transmitter in room in which you intend to use it. Rotate
transmitter power/volume dial to turn power on. Set transmitter
channel switch to same channel as receiver. Turn on a radio.
Power Indicator
Power/Volume Dial
Power/Volume Dial
Test transmitter transmission and receiver reception.
Place receiver in room in which you intend to use it. Rotate
power/volume dial to turn power on. Adjust receiver location.
Power Indicator
Static
Buzzzz
Adjust Channel
Adjust Channel
Fisher-Price, Inc., a subsidiary of Mattel, Inc., East Aurora, New York 14052, U.S.A.
©2006 Mattel, Inc. All Rights Reserved.
® and ™ designate U.S. trademarks of Mattel, Inc.
PRINTEd IN ChINA
h7178a-0726

Setup & Use
12
11
2
3
1
6
5
14
7
7
9
10
Ceiling Light Show
Music/Sound Effects
RECEIVER
TRANSMITTER
8
5

Setup & Use
IMPORTANT! Test sound reception of this monitor before first
time use and whenever you change location of transmitter
(see page 4).
1. Set transmitter channel switch to same channel as receiver.
2. Place transmitter in same room with child. Point micro-
phone directly toward crib or play area.
3. Unwrap and fully extend power cord for best transmission.
Insert power cord plug into wall outlet.
4. Rotate transmitter power/volume dial to turn power on.
Power indicator lights.
5. If you’d like baby to enjoy sounds or music, slide the
sound switch to:
Location: Transmitter (TX) BUTTON front
music; sound effects or Ooff.
Press the start button. Sounds turn on gradually to the
volume selected.
6. If you’d like to entertain baby with a ceiling light show, slide
the light switch to . Press the start button. Lights turn on
gradually. To turn the ceiling light show off, slide the light
switch to O.
7. You can adjust where the ceiling light show projects and the
image clarity. Rotate the transmitter on the base to project
the light show over baby's crib. Now, rotate the lens to focus
the image.
8. Rotate power/volume dial to adjust volume.
9. If you would like the light show/music or sound effects to
automatically turn on when baby fusses or cries, rotate the
sound sensor dial on. Now, adjust the sensitivity for
baby’s sounds. Rotate towards for high sensitivity (shallow
sounds); rotate towards for low sensitivity (loud sounds).
To turn this automatic feature "off", rotate the sound sensor
to Ooff.
Hint: You may want to start with the high sensitivity setting at first.
10. Press the start button. Light show/music or sound effects
will gradually turn on for about 10 minutes and then
automatically turn off. If you’d like to turn off lights/music/
sound effects, press the start button on the transmitter.
Lights/music/sound effects gradually turn off.
11. Place receiver where you will see or hear it.
12. Unwrap and fully extend AC adaptor cord for best reception.
Insert AC adaptor jack into receiver socket and plug into
wall outlet.
Note: To use LR6 (AA) alkaline batteries for power source, refer
to "Receiver Battery Installation" instructions on page 3.
13. Rotate receiver power/volume dial to turn power on.
Power indicator lights. Rotate power/volume dial to
adjust volume.
12
11
13
6

Replacing the Light Bulb (Glass Bulb)
IMPORTANT! Should light bulb become non-functional, you are
advised to remove and replace it. This should be carried out away
from child’s sleep or play area.
Light Bulb Compartment Door
• Loosen screws in light bulb compartment door with a
Phillips screwdriver.
• Lift to remove light bulb compartment door.
Hint: You may need to fit a flat edged object to pry light bulb
compartment door up.
1
2
Retainer
• Turn light bulb compartment door so that inside faces up.
• Loosen and remove two screws in the retainer with a Phillips
screwdriver. Remove retainer.
4
3
Reflector Lens
Tab
Notch
Groove
• While pressing lens of reflector , lift it from light bulb
compartment cover.
• Remove and properly discard light bulb .
• Replace light bulb with a new PR12 or equivalent light bulb.
Note: When replacing light bulb, be sure to discard light bulb
properly. Beware of cracked or broken glass.
• At an angle, fit reflector over new light bulb.
• Align notch in reflector with tab in light bulb receptacle.
• Push reflector lens slightly and fit reflector edges into grooves in
light bulb compartment cover.
7

56
• Replace retainer and insert two screws.
• Tighten screws with a Phillips screwdriver. Do not over-tighten.
• Fit light bulb compartment door into back of transmitter. Press light
bulb compartment door to "snap" into place.
• Tighten screws in light bulb compartment door with Phillips screw-
driver. Do not over-tighten.
Light Bulb Compartment Door
Replacing the Light Bulb (Glass Bulb)
8

“Mum, mum, mum, mum…”
Circuit Breaker
Problems & Solutions
5
PROBLEMS SOLUTIONS
1. Transmitter power indicator not lit. Turn transmitter power on. Power indicator lights.
2. You hear static or buzzing from receiver. Make sure channel switches on both transmitter and receiver are set to
same channel.
3. Transmitter power indicator not lit. Make sure light switch that controls power flow to wall outlet is on.
4. Transmitter power indicator not lit. Check AC adaptor cord plug-to-outlet connection.
5. Transmitter power indicator not lit. Power is off because circuit breaker for baby’s room is off.
Make sure house fuses and circuit breakers are on.
6. You hear static or buzzing and all four dots Check all five solutions above. Any one or more of these solutions
light on receiver. should solve the problem.
7. Baby’s sounds do not activate transmitter The sound sensitivity dial is set too low. Turn the sound sensitivity
light show/music/sound effects. dial to a high setting .
Hint: If, after checking all of these solutions, you believe that your transmitter
power cord or AC adaptor is damaged, please contact Mattel.
“That doesn’t sound right.
Maybe we should check the transmitter.”
7
3
4
6
2
21
Buzzzz
9

PROBLEM SOLUTION
You can hear conversations or sounds from other homes. There is signal interference due to other nursery monitors on same
channel or cordless telephone use. Change channel switches on both
transmitter and receiver to eliminate source of interference.
Hints: Do not use more than one transmitter and one receiver at same time in same
household. Always remember that you are using public airwaves when using your
monitor. Conversations, even from rooms near transmitter, may broadcast to other
nursery monitors, radios, cordless telephones, or scanners outside your home.
To protect privacy of your home, always turn transmitter off when not in use.
Problems & Solutions
“That must be
Susie next
door…”
“That must be
coming from
next door…”
“Did you read about…”
“Wah, Wah, Wah…”
“Did you read about…”
“I better get off
the telephone,
she’s up…”
“Wah, Wah, Wah…” “Wah, Wah, Wah…”
10