FiveCo CDC6 User manual

CDC6 Specifications

F ABBRICA ITALIANA VEICOLI ELETTRICI
2
Contents
1、About the User Manual..................................................................................... 3
2、Characteristics................................................................................................... 3
3、Functions and Display....................................................................................... 4
4、Buttons.............................................................................................................. 5
5、Installation ........................................................................................................ 5
6、Functions........................................................................................................... 6
7、Error codes........................................................................................................ 8

F ABBRICA ITALIANA VEICOLI ELETTRICI
3
1、About the User Manual
Dear users,
to ensure better performance of your e-bike, please read carefully through the
CDC6 Specifications before using it.
2、Characteristics
CDC6 products use a 3.5-inch LCD display, double PCB, nylon buckle, ABS
material shell and a keyboard. See Figure 1 (unit:mm).
Figure 1

F ABBRICA ITALIANA VEICOLI ELETTRICI
4
3、Functions and Display
CDC6 is a Multifunction 3.5-inch LCD display. The same display can match 24V,
36V and 48V batteries
CDC6 functions Summary (Figure 2):
•Total distance indicator
•Riding distance indicator
•Current speed indicator
•PAS level selection
•Residual battery capacity indicator
•Error code definition
•Kilometers or miles
•Wheel diameter selection
•USB charging function
•6Km/h implementation function
Figure 2
1/2
3/4
5

F ABBRICA ITALIANA VEICOLI ELETTRICI
5
4、Buttons
CDC6 has four buttons: ON/OFF, UP, DOWN and SET.
Figure 3
5、Installation
Mount the display on the handlebar and then adjust the view angle. Install the
keyboard in a position, where it is easy to control. Tighten the screws to
complete the installation (Figure 4):
Figure 4

F ABBRICA ITALIANA VEICOLI ELETTRICI
6
6、Functions
a. on/off
Press the ON/OFF button once to turn on the display. Press and hold for 3
seconds to turn off the display.
b. Turn on/off headlights (if supported)
If supported by the ebike, while the display is on, press the ON/OFF button to
turn on or off the headlights.
c. PAS level selection
With the screen on, press the “+” or “-“buttons to increase or decrease the
assistance levels from 0 (no power) to 5 (max power). While in 0 assistance
level, hold the “-“ button to activate the walking assisted mode. This mode will
help you push the e-bike by foot up to a maximum of 6 km/h speed
d. Speed unit selection
The display supports km/h and MPH speed units. To switch from a unit to
another, hold the “M” button to enter Settings. Then press the “M” button
until the speed unit interface appears on the display (Figure 5). By clicking the
“+” button, the preferred speed unit can be selected.
Figure 5

F ABBRICA ITALIANA VEICOLI ELETTRICI
7
e. Battery indicator
The residual charge of the battery is shown on the top-right part of the
display. When the battery is full, the five notches are all bright. With low
battery, the last one flashes and the battery needs to be recharged
immediately. See Figure 6:
Figure 6
f. Wheel diameter selection
Press and hold for 5 seconds the “M” button to open the Settings Interface,
then click the “M” button until the wheel diameter setting interface is reached
(Figure 7). With “-“ and “+” select the correct diameter (Figure 8). To choose a
diameter other than the real one may cause malfunctions.
Figure 7 Figure 8

F ABBRICA ITALIANA VEICOLI ELETTRICI
8
7、Error codes
The error codes are shown at the bottom-right of the display. Check the following
Table. In case of error, please contact the Technical Support.
Error code definition table
Error code
Description
2
Overcurrent protection / Motor’s Hall signal anomaly /
controller’s internal power device / motor’s phase missing
3
Motor’s Hall signal anomaly / safety shutdown of the motor
anomaly / bad contact of power supply terminal / damage control /
motor damage
4
Low voltage
5
Faulty brakes sensor
6
Battery anomaly
7
Throttle anomaly
9
Voltage anomaly
A/10
Display and controller communication fault (yellow cable)
F/15
Display and controller communication fault (green cable)
Display does not turn on or shuts down after 3 second from turning on: please check
that controller cables or supply power cables are well connected.