FLIR MPX C134BD Series User manual

Package Contents
C134BD Series
QUICK START GUIDE
English Version 1.0
flir.com/security/support
FLIR Systems, Inc., Copyright © 2015
As our products are subject to continuous improvement, FLIR
Systems Inc. reserves the right to modify product design,
specifications and prices, without notice and without incurring
any obligation. E&OE
Safety Precautions
• Use an appropriate low voltage power cable to
prevent fire or electrical shock.
• Make sure to install the camera in an area that can
support the camera weight.
• There are no user serviceable parts inside the
camera. Please do not disassemble the camera.
• Do not clean the lens cover with an abrasive cleaning
material. Please use a soft cloth to clean the lens
cover.
1080P Varifocal WDR Bullet Camera
flir.com/security/support
VISIT
• 1x Varifocal Bullet Camera
• 3x Mounting Screws
• 3x Drywall Anchors
• 1x Allen Key
• 1x Mounting Template
• 1x Power Pigtail Adapter
NOTE: 12V DC power supply not included.
IT’S ALL ON THE WEB!
On-Screen Display (OSD) Menu
AE Brightness
Exposure Mode
WB Mode
Day-Night Mode
Video Setting Contrast
Sharpness
Color Gain
WDR
Format
Language
Reset
Save-Exit
Exit
To use the OSD menu:
1. In Live View, double-click the channel that has
the camera connected to open in full-screen.
2. Right-click and click Pan/Tilt/Zoom. Enter the
system user name and password if prompted. The
PTZ menu opens.
3. Click the arrow in the PTZ control window to
show advanced controls.
4. Click . The OSD menu appears over the
camera image.
5. Use the on-screen controls to configure menu
items:
• Up / down arrows: Select menu items.
• Left / right arrows: Change values for menu
items.
• Esc: Exit the OSD menu.
• Enter: Confirm selection.
Select Return to return to the previous menu, or
Exit from the main menu to exit.
Note: These instructions are based on current
MPX DVR interface. If you are not able to access
your DVR’s OSD menu by following these steps,
please use the instructions in your DVR manual
instead.
You can configure the camera’s advanced
settings on an MPX DVR using the OSD menu.
See the full OSD menu tree below.

Camera Dimensions
To install the camera:
1. Use the included mounting template to mark and drill
holes for the included mounting screws.
NOTE: Insert the included drywall anchors if installing into
drywall.
2. Connect the video and power cable as detailed in the
section ‘Setting up the Camera’.
3. Attach the camera
base to the mouting
surface using the
included screws.
4. Set the position and angle of the camera using the
provided Allen key.
5. Remove the protective film from the camera lens.
10.6”
269mm
3.9”
99mm
3.5”
89mm
ATTENTION:
Test the camera prior to selecting a permanent
mounting location by temporarily connecting the
camera(s) and cables to the DVR.
Installing the Camera
Extension Cable Options
Specification Maximum Length
RG59 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 1500ft (455m)†
RG6 20AWG Conductor 95% Braid
CSA/UL or C(UL) Approved
Up to 2300ft (700m)†
Analog CCTV Balun Up to 300ft (91m)
† Long cable runs over 1000ft (300m) may be affected by
electro-mechanical interference (EMI), which can increase the
amount of noise in the picture in some installations.
The entire length of the cable run must be made using a
single extension cable between the camera and the DVR.
B) Loosen lower screw with
the Allen key to adjust the
camera’s vertical position.
C) Loosen the screws on either side of the
camera stand with the Allen key to rotate the
camera housing. Loosen the right-side to make
fine adjustments, or the left-side for broad
adjustments.
A) Loosen the screw on the
camera base with the Allen
key to tighten / loosen the
stand connection. Adjust the
camera’s horizontal position.
A B
C
Adjusting Zoom & Focus
Use the included Allen key to adjust
the zoom and focus control screws
on the underside of the camera as
required.
C134BD_SERIES_QSG_EN_R1
Resources
Go to flir.com/security/support
Search the model number of your product
Click on your product in the search results
Click on the Downloads tab
1
2
3
4
Need Help?
Visit us online for up-to-date
software and complete instruction manuals
Setting up the Camera
WARNING:
A REGULATED 12V DC power supply is REQUIRED for use with
this camera. Use of a non-regulated, non-conforming power
supply can damage this product and voids the warranty.
1. Connect the BNC connector on the camera to the video
cable. See “Camera Wiring” for details.
2. DC Power—Power Pigtail: Connect the included power
pigtail to the camera. Connect the terminating wires of the
cable directly to the DC power source.
OR
DC Power—Power Adapter: Connect a 12V DC power adapter
(not included) to the camera and a local power outlet.
NOTE: For pigtail connection with 12V DC, make sure to check
polarity specifications on the power adapter.
MPX
Connect to the included
power pigtail or a 12V
DC power adapter
(not included).*
Connect to an MPX DVR
Camera Wiring
* Camera focus may be affected if the power connection is too
long. It is recommended not to extend the power connection
past 200ft (61m).