FLIR Lorex DV700FS Series User manual

Instruction Manual
DV700FS Series

Instruction Manual
DV700FS Series
#LX400060; r.37992/37992; en-US iii

Thank you for purchasing this product. Lorex Corporation is committed to providing our customers with a
high quality, reliable security solution.
This manual refers to the following models:
DV704 (4-channel)
DV708 (8-channel)
DV716 (16-channel)
For the latest online manual, downloads and product updates, and to learn about our complete line of
accessory products, please visit our website at:
www.lorextechnology.com
WARNING
RISK OF ELECTRIC SHOCK
DO NOT OPEN
WARNING: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE
COVER. NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol, within an equilateral
triangle, is intended to alert the user to the presence of uninsulated
"dangerous voltage" within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
WARNING: TO PREVENT FIRE OR SHOCK HAZARD, DO NOT EXPOSE THIS UNIT
TO RAIN OR MOISTURE.
CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF THE PLUG
TO THE WIDE SLOT AND FULLY INSERT.
#LX400060; r.37992/37992; en-US iv

Table of contents
1 Important Safeguards ..........................................................................1
1.1 General Precautions....................................................................1
1.2 Installation................................................................................. 1
1.3 Service.....................................................................................3
1.4 Use..........................................................................................3
2Getting Started (DV700FS Series) .............................................................4
3Front Panel (DV700FS Series) ...................................................................5
3.1 DV704 / DV708 / DV716 ............................................................... 5
4Rear Panel (DV700FS Series) ....................................................................6
5Basic Setup (DV700FS Series) ..................................................................8
5.1 Step 1: Connect the BNC Cameras................................................. 8
5.2 Step 2: Connect the Mouse........................................................... 8
5.3 Step 3: Connect the Ethernet Cable ................................................8
5.4 Step 4: Connect the Monitor..........................................................9
5.5 Step 5: Connect the Power Adapter and Power on the DVR..................9
5.6 Step 6: Upgrade Firmware to Latest Version (if Available) ....................9
5.7 Step 7: Verify Camera Image ....................................................... 10
5.8 Step 8: Set the Time .................................................................. 10
5.9 Default System Password & Port Numbers ..................................... 10
5.9.1 Remote Connectivity....................................................... 10
5.10 Quick Access to System Information ............................................. 11
5.11 Connecting Cameras ................................................................. 11
5.11.1 Camera Compatibility...................................................... 11
5.11.2 About Lorex MPX Cameras .............................................. 11
5.11.3 Installing Cameras.......................................................... 11
5.11.4 Connecting Camera Extension Cables................................ 12
5.11.5 Extension Cable Options ................................................. 13
6 Mouse Control .................................................................................. 15
7 Remote Control ................................................................................. 16
7.1 Setting the Remote Control Address ............................................. 17
8 Using the System .............................................................................. 18
8.1 On-Screen Display .................................................................... 18
8.2 Using the Quick Menu................................................................ 18
8.3 Adjusting Color Settings ............................................................. 19
8.4 Using the Navigation Bar ............................................................ 20
8.5 Using the Camera Toolbar .......................................................... 21
8.5.1 Using Instant Playback .................................................... 21
8.5.2 Using Zoom in Live Display .............................................. 22
8.5.3 Using Realtime Backup ................................................... 22
8.6 Using the Virtual Keyboard.......................................................... 22
9 Setting The Time ............................................................................... 24
10 Recording......................................................................................... 25
10.1 Video Recording Types .............................................................. 25
10.2 Main Stream and Sub Stream ...................................................... 25
10.3 Setting up Scheduled or Manual Recording .................................... 25
10.4 Configuring Hard Drive Overwrite ................................................. 26
11 Search (Playback) ............................................................................. 28
11.1 Playing Back Video from the Hard Drive......................................... 28
11.2 Playback Controls ..................................................................... 29
#LX400060; r.37992/37992; en-US v

Table of contents
11.3 Playing Back from a USB Drive .................................................... 29
11.4 Using Smart Search .................................................................. 30
12 Backup............................................................................................. 32
12.1 Formatting the USB Thumb Drive ................................................. 32
12.2 Backing up Video...................................................................... 33
12.3 Using Video Clip Backup ............................................................ 34
12.4 Viewing Backup Files................................................................. 35
12.4.1 Viewing Backup Files on PC ............................................. 35
12.4.2 Viewing Backup Files on Mac ........................................... 38
13 Managing Passwords and User Accounts............................................. 41
13.1 Changing Passwords................................................................. 41
13.2 Adding Users ........................................................................... 42
13.3 Modifying Users ....................................................................... 43
13.4 Deleting Users ......................................................................... 43
13.5 Account Groups ....................................................................... 44
13.6 Adding Groups ......................................................................... 44
13.7 Modifying Groups ..................................................................... 45
13.8 Deleting Groups ....................................................................... 45
14 Using the Main Menu ......................................................................... 46
14.1 Camera .................................................................................. 46
14.1.1 Recording..................................................................... 46
14.1.2 Configuring Recording Quality .......................................... 47
14.1.3 Configuring Snapshot Recording Settings............................ 49
14.1.4 Creating Custom Channel Names...................................... 49
14.1.5 Selecting Cable Type (Advanced) ...................................... 50
14.2 Info........................................................................................ 51
14.2.1 HDD Info...................................................................... 51
14.2.2 Record Info ................................................................... 51
14.2.3 Version ........................................................................ 52
14.2.4 Alarm Status ................................................................. 52
14.2.5 Online Users ................................................................. 53
14.2.6 Load............................................................................ 53
14.2.7 Test............................................................................. 54
14.2.8 BPS ............................................................................ 54
14.2.9 Log ............................................................................. 54
14.3 Setting.................................................................................... 56
14.3.1 Network ....................................................................... 56
14.3.2 Selecting DHCP or Static IP Address (TCP/IP) ...................... 56
14.3.3 Configuring System Ports (Connection)............................... 57
14.3.4 Configuring DDNS Settings .............................................. 57
14.3.5 Configuring Email Alerts .................................................. 58
14.3.6 Event........................................................................... 59
14.3.7 Configuring Motion Detection............................................ 59
14.3.8 Configuring Video Loss Settings ........................................ 62
14.3.9 Configuring Hard Drive Warnings....................................... 63
14.3.10 Configuring Network Warnings .......................................... 64
14.3.11 Storage........................................................................ 64
14.3.12 Configuring the Video Recording Schedule .......................... 65
14.3.13 Configuring Pre-Recording ............................................... 66
14.3.14 Configuring the Snapshot Schedule ................................... 66
#LX400060; r.37992/37992; en-US vi

Table of contents
14.3.15 Configuring Holidays....................................................... 67
14.3.16 Formatting the Hard Drive ................................................ 68
14.3.17 Configuring Hard Drive Type ............................................. 69
14.3.18 Configuring General System Settings ................................. 69
14.3.19 Setting the Monitor Resolution (Display) .............................. 70
14.3.20 Saving Your System Configuration to a USB Flash
Drive ........................................................................... 71
14.3.21 Setting the System to Factory Defaults................................ 72
14.3.22 Upgrading Firmware from USB.......................................... 72
14.4 Shutdown................................................................................ 74
15 Connecting to Your System Over the Internet on PC or Mac .................... 75
15.1 System Requirements................................................................ 75
15.2 Step 1 of 3: Connect your System to Your Router ............................. 75
15.3 Step 2 of 3: Obtain the system’s Device ID...................................... 76
15.4 Step 3 of 3: Connect to the System Over the Internet ........................ 76
16 Using FLIR Cloud™ Client for PC or Mac .............................................. 80
16.1 Home Page ............................................................................. 80
16.2 Live View ................................................................................ 80
16.2.1 Live View Controls.......................................................... 81
16.2.2 Opening Live View in Multiple Monitors ............................... 82
16.3 Controlling PTZ Cameras ........................................................... 83
16.3.1 PTZ Presets.................................................................. 84
16.3.2 PTZ Tours..................................................................... 85
16.3.3 PTZ Pattern .................................................................. 86
16.3.4 PTZ Scan ..................................................................... 87
16.3.5 PTZ Pan....................................................................... 87
16.4 Playback................................................................................. 87
16.5 Playback Controls ..................................................................... 89
16.6 Downloading Video to your Computer Hard Drive............................. 90
16.7 Alarm ..................................................................................... 91
16.8 Log........................................................................................ 92
16.9 E-map .................................................................................... 93
16.10 Devices .................................................................................. 95
16.11 Device Config .......................................................................... 96
16.12 Alarm CFG .............................................................................. 96
16.13 Tour & Task ............................................................................. 99
16.14 Account................................................................................ 100
16.14.1 Managing User Accounts ............................................... 100
16.14.2 Managing Roles........................................................... 102
16.15 General ................................................................................ 103
16.15.1 Basic......................................................................... 103
16.15.2 File ........................................................................... 103
16.15.3 Alarm Prompt .............................................................. 104
16.15.4 Version ...................................................................... 105
17 Connecting to your System Using Smartphone or Tablet Apps.............. 106
17.1 FLIR Secure™ ....................................................................... 106
17.1.1 Connect to Your Mobile Device Using FLIR Secure™ ........... 106
17.1.2 iPhone ....................................................................... 107
17.1.3 Android Phone ............................................................ 116
17.2 FLIR Cloud™......................................................................... 125
17.2.1 iPhone ....................................................................... 125
#LX400060; r.37992/37992; en-US vii

Table of contents
17.2.2 iPad .......................................................................... 139
17.2.3 Android...................................................................... 154
18 DDNS Setup (Advanced) .................................................................. 166
18.1 Accessing your System within a Local Network (LAN) ..................... 166
18.1.1 Step 1 of 3: Connect your System to Your Router ................ 166
18.1.2 Step 2 of 3: Obtain the System’s Local IP Address ............... 167
18.1.3 Step 3 of 3: Connect to the System’s Local IP
Address ..................................................................... 167
18.2 DDNS Setup—Access your System Remotely over the
Internet................................................................................. 169
18.2.1 Step 1 of 4: Port Forwarding ........................................... 170
18.2.2 Step 2 of 4: Create a DDNS Account ................................ 170
18.2.3 Step 3 of 4: Enable DDNS on the System .......................... 174
18.2.4 Step 4 of 4: Connect to the System’s DDNS Address ........... 174
19 DV700FS Series Hard Drive Installation.................................................. 178
19.1 Installing a Hard Drive.............................................................. 178
19.1.1 DV704 / DV708 / DV716 ................................................ 178
19.2 Removing the Hard Drive.......................................................... 179
19.2.1 DV704 / DV708 / DV716 ................................................ 179
19.3 Formatting Hard Drives ............................................................ 180
20 Connecting a PTZ Camera (DV700FS Series) .......................................... 182
20.1 Controlling a PTZ Camera (Local DVR)........................................ 183
20.2 Advanced PTZ Controls ........................................................... 184
20.2.1 Presets ...................................................................... 185
20.2.2 Tours......................................................................... 185
20.2.3 Pattern....................................................................... 186
20.2.4 Auto Scan .................................................................. 186
21 Recording Audio ............................................................................. 188
21.1 Step 1 of 2: Connecting a Self-powered Microphone....................... 188
21.2 Step 2 of 2: Configuring Audio Recording..................................... 188
22 Troubleshooting .............................................................................. 190
23 DV700FS Series System Specifications.................................................. 192
24 Notices........................................................................................... 195
24.1 FCC/IC Notice........................................................................ 195
24.2 Modification........................................................................... 195
24.3 ROHS .................................................................................. 195
#LX400060; r.37992/37992; en-US viii

Important Safeguards
1
In addition to the careful attention devoted to quality standards in the manufacturing proc-
ess of your product, safety is a major factor in the design of every instrument. However,
safety is your responsibility too. This sheet lists important information that will help to en-
sure your enjoyment and proper use of the product and accessory equipment. Please read
them carefully before operating and using your product.
1.1 General Precautions
1. All warnings and instructions in this manual should be followed.
2. Remove the plug from the outlet before cleaning. Do not use liquid aerosol detergents.
Use a water-dampened cloth for cleaning.
3. Do not use this product in humid or wet places.
4. Keep enough space around the product for ventilation. Slots and openings in the stor-
age cabinet should not be blocked.
5. It is highly recommended to connect the product to a surge protector to protect from
damage caused by electrical surges. It is also recommended to connect the product to
an uninterruptible power supply (UPS), which has an internal battery that will keep the
product running in the event of a power outage.
CAUTION
Maintain electrical safety. Power line operated equipment or accessories connected to this product
should bear the UL listing mark or CSA certification mark on the accessory itself and should not be modi-
fied so as to defeat the safety features. This will help avoid any potential hazard from electrical shock or
fire. If in doubt, contact qualified service personnel.
1.2 Installation
1. Read and Follow Instructions - All the safety and operating instructions should be
read before the product is operated. Follow all operating instructions.
2. Retain Instructions - The safety and operating instructions should be retained for fu-
ture reference.
3. Heed Warnings - Comply with all warnings on the product and in the operating
instructions.
4. Polarization - Do not defeat the safety purpose of the polarized or grounding-type
plug.
A polarized plug has two blades with one wider than the other.
A grounding type plug has two blades and a third grounding prong.
The wide blade or the third prong are provided for your safety.
If the provided plug does not fit into your outlet, consult an electrician for replacement
of the obsolete outlet.
#LX400060; r.37992/37992; en-US 1

Important Safeguards
1
5. Power Sources - This product should be operated only from the type of power source
indicated on the marking label. If you are not sure of the type of power supplied to your
location, consult your video dealer or local power company. For products intended to
operate from battery power, or other sources, refer to the operating instructions.
6. Overloading - Do not overload wall outlets or extension cords as this can result in the
risk of fire or electric shock. Overloaded AC outlets, extension cords, frayed power
cords, damaged or cracked wire insulation, and broken plugs are dangerous. They
may result in a shock or fire hazard. Periodically examine the cord, and if its appear-
ance indicates damage or deteriorated insulation, have it replaced by your service
technician.
7. Power-Cord Protection - Power supply cords should be routed so that they are not
likely to be walked on or pinched by items placed upon or against them. Pay particular
attention to cords at plugs, convenience receptacles, and the point where they exit
from the product.
8. Surge Protectors - It is highly recommended that the product be connected to a
surge protector. Doing so will protect the product from damage caused by power
surges. Surge protectors should bear the UL listing mark or CSA certification mark.
9. Uninterruptible Power Supplies (UPS) - Because this product is designed for con-
tinuous, 24/7 operation, it is recommended that you connect the product to an uninter-
ruptible power supply. An uninterruptible power supply has an internal battery that will
keep the product running in the event of a power outage. Uninterruptible power sup-
plies should bear the UL listing mark or CSA certification mark.
10. Ventilation - Slots and openings in the case are provided for ventilation to ensure reli-
able operation of the product and to protect it from overheating. These openings must
not be blocked or covered. The openings should never be blocked by placing the prod-
uct on a bed, sofa, rug, or other similar surface. This product should never be placed
near or over a radiator or heat register. This product should not be placed in a built-in
installation such as a bookcase or rack unless proper ventilation is provided and the
product manufacturer’s instructions have been followed.
11. Attachments - Do not use attachments unless recommended by the product manu-
facturer as they may cause a hazard.
12. Water and Moisture - Do not use this product near water — for example, near a bath
tub, wash bowl, kitchen sink or laundry tub, in a wet basement, near a swimming pool
and the like.
13. Heat - The product should be situated away from heat sources such as radiators, heat
registers, stoves, or other products (including amplifiers) that produce heat.
14. Accessories - Do not place this product on an unstable cart, stand, tripod, or table.
The product may fall, causing serious damage to the product. Use this product only
with a cart, stand, tripod, bracket, or table recommended by the manufacturer or sold
with the product. Any mounting of the product should follow the manufacturer’s instruc-
tions and use a mounting accessory recommended by the manufacturer.
15. Camera Extension Cables – Check the rating of your extension cable(s) to verify
compliance with your local authority regulations prior to installation.
16. Mounting - The cameras provided with this system should be mounted only as in-
structed in this guide or the instructions that came with your cameras, using the pro-
vided mounting brackets.
#LX400060; r.37992/37992; en-US 2

Important Safeguards
1
17. Camera Installation - Cameras are not intended for submersion in water. Not all cam-
eras can be installed outdoors. Check your camera environmental rating to confirm if
they can be installed outdoors. When installing cameras outdoors, installation in a
sheltered area is required.
1.3 Service
1. Servicing - Do not attempt to service this product yourself, as opening or removing
covers may expose you to dangerous voltage or other hazards. Refer all servicing to
qualified service personnel.
2. Conditions Requiring Service - Unplug this product from the wall outlet and refer
servicing to qualified service personnel under the following conditions:
• When the power supply cord or plug is damaged.
• If liquid has been spilled or objects have fallen into the product.
• If the product has been exposed to rain or water.
• If the product has been dropped or the cabinet has been damaged
• If the product does not operate normally by following the operating instructions. Ad-
just only those controls that are covered by the operating instructions. Improper ad-
justment of other controls may result in damage and will often require extensive
work by a qualified technician to restore the product to its normal operation.
• When the product exhibits a distinct change in performance. This indicates a need
for service.
3. Replacement Parts - When replacement parts are required, have the service techni-
cian verify that the replacements used have the same safety characteristics as the orig-
inal parts. Use of replacements specified by the product manufacturer can prevent fire,
electric shock, or other hazards.
4. Safety Check - Upon completion of any service or repairs to this product, ask the
service technician to perform safety checks recommended by the manufacturer to de-
termine that the product is in safe operating condition.
1.4 Use
1. Cleaning - Unplug the product from the wall outlet before cleaning. Do not use liquid
cleaners or aerosol cleaners. Use a damp cloth for cleaning.
2. Product and Cart Combination - When product is installed on a cart, product and
cart combination should be moved with care. Quick stops, excessive force, and un-
even surfaces may cause the product and cart combination to overturn.
3. Object and Liquid Entry - Never push objects of any kind into this product through
openings as they may touch dangerous voltage points or “short-out” parts that could
result in a fire or electric shock. Never spill liquid of any kind on the product.
4. Lightning - For added protection of this product during a lightning storm, or when it is
left unattended and unused for long periods of time, unplug it from the wall outlet and
disconnect the antenna or cable system. This will prevent damage to the product due
to lightning and power line surges.
#LX400060; r.37992/37992; en-US 3

Getting Started (DV700FS Series)
2
The system comes with the following components:
DVR (Digital Video Recorder) 12V DC power supply Remote control
(may not be exactly as shown)
USB mouse Ethernet cable HDMI cable
Quick start guides
Hard drive size, number of channels, and camera configuration may vary by model. Please
refer to your package for specific details. Check your package to confirm that you have re-
ceived the complete system, including all components shown above.
#LX400060; r.37992/37992; en-US 4

Front Panel (DV700FS Series)
3
3.1 DV704 / DV708 / DV716
1. IR receiver and LED indicators: IR receiver for the remote control. Keep the IR re-
ceiver clear from obstructions.
•POWER: Glows to indicate the system is on.
•NET: Glows when network is in normal state. Turns off for network error.
•HDD: Glows to indicate hard drive is in normal state. Turns off when there is a hard
drive error.
•ALARM: Not supported.
2. FN: Performs special functions in some menus.
3. ESC: In menus, press to go back / exit menus. In playback, press to return to live view.
4. Directional buttons:
•: From live view, press once to open the System Information screen. In menus,
press to confirm menu options.
•Directional buttons: Press to move cursor in menus. In live view, press up to
change split screen layout; press left / right to select channels when single-channel
mode is selected.
5. USB port: Connect a USB mouse (included) or connect a USB flash drive (not in-
cluded) for data backup or firmware upgrades.
6. Power button: Press and hold to power off the system (system password required).
Press to power the system back on.
#LX400060; r.37992/37992; en-US 5

Rear Panel (DV700FS Series)
4
DV704 (4–Channel)
DV708 (8–Channel)
1. On / Off switch: Turns the DVR on or off.
2. VGA: Connect a VGA monitor (not included) to view the system interface.
3. DC12V: Connect the included AC power adapter.
4. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
5. A/B: Connect RS485 cables for analog PTZ cameras. See 20 Connecting a PTZ
Cam-era (DV700FS Series), page 182 for more details.
NOTE
Lorex 1080p MPX and 720p wired HD PTZ cameras can accept commands directly via the video
cable.
6. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
7. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
8. Audio IN/Audio OUT (RCA): Connect a self-powered microphone (not included) to
the Audio IN port to record one channel of audio. Connect a speaker to the Audio OUT
port. See 21 Recording Audio, page 188 for more details.
9. Video input: Connect Lorex 1080p MPX, 720p HD, or analog cameras.
DV716 (16–Channel)
1. On / Off switch: Turns the DVR on or off.
2. DC12V: Connect the included AC power adapter.
#LX400060; r.37992/37992; en-US 6

Rear Panel (DV700FS Series)
4
3. A/B: Connect RS485 cables for analog PTZ cameras. See 20 Connecting a PTZ Cam-
era (DV700FS Series), page 182 for more details.
NOTE
Lorex 1080p MPX and 720p HD PTZ cameras can accept commands directly via the video cable.
4. LAN: Connect a CAT 5 RJ45 Ethernet cable for local and remote connectivity.
5. USB port(s): Connect a USB mouse (included) or USB flash drive (not included) for
data backup or firmware updates.
6. VGA: Connect a VGA monitor (not included) to view the system interface.
7. HDMI: Connect to an HDMI monitor or TV (not included) to view the system interface.
8. Audio IN/Audio OUT: Connect a self-powered microphone (not included) to the Audio
IN port to record one channel of audio. Connect a speaker to the Audio OUT port. See
21 Recording Audio, page 188 for more details.
9. Video input: Connect Lorex 1080p MPX, 720p HD, or analog cameras.
#LX400060; r.37992/37992; en-US 7

Basic Setup (DV700FS Series)
5
5.1 Step 1: Connect the BNC Cameras
• Connect cameras to the Video Input ports on the rear panel of the DVR.
NOTE
Connect Lorex 1080p MPX, 720p HD, or analog cameras to the system. For a list of compatible cam-
eras, please visit www.lorextechnology.com/support.
Push and twist the BNC connector clockwise to secure it to the BNC port.
5.2 Step 2: Connect the Mouse
• Connect a USB mouse (included) to one of the USB ports.
5.3 Step 3: Connect the Ethernet Cable
• Connect an Ethernet cable (included) to the LAN port on the rear panel of the DVR.
Connect the other end of the Ethernet cable to a router on your network.
#LX400060; r.37992/37992; en-US 8

Basic Setup (DV700FS Series)
5
5.4 Step 4: Connect the Monitor
• Connect the included HDMI cable from the HDMI port to the TV or monitor
(recommended).
OR
• Connect a VGA cable (not included) from the VGA port to the monitor.
1. VGA port.
2. HDMI port.
5.5 Step 5: Connect the Power Adapter and Power on the DVR
1. Connect the included power adapter to the DC 12V port. Connect the end of the power
adapter to a wall socket or a surge protector.
2. Turn the power switch to ON to turn on the DVR.
At startup, the system performs a basic system check and runs an initial loading sequence.
After a few moments, the system loads a live display view.
5.6 Step 6: Upgrade Firmware to Latest Version (if Available)
If a firmware upgrade is available, you will be asked to install it once the system starts up.
It is required to upgrade your system firmware and client software or mobile apps to the lat-
est version to enable remote connection to the system.
If a firmware upgrade is available:
1. After startup, a notification will appear asking you to upgrade the firmware. Click OK to
upgrade.
#LX400060; r.37992/37992; en-US 9

Basic Setup (DV700FS Series)
5
2. Enter the system user name (default: admin) and password (default: 000000) and
click OK. Wait for the firmware update to complete. The system will restart once the
firmware has been upgraded.
WARNING
DO NOT POWER OFF THE SYSTEM OR DISCONNECT THE POWER CABLE DURING FIRM-
WARE INSTALLATION
5.7 Step 7: Verify Camera Image
• Power on the cameras, and then verify the camera video quality before mounting the
cameras to a permanent location.
• Mount the cameras under a sheltered location. Always verify the outdoor rating of your
camera before installing it in a permanent location.
5.8 Step 8: Set the Time
• Set the system time and date for accurate video time stamps. Videos with inaccurate
times may not be valid as surveillance evidence.
• For details on setting the system time, see 9 Setting The Time, page 24.
5.9 Default System Password & Port Numbers
CAUTION
By default, the system user name is admin and the password is 000000. It is essential that you create
your own password. For details, see 13 Managing Passwords and User Accounts, page 41.
The system requires a user name and password to log in to the system remotely using a
computer or mobile device. After logging on remotely the first time, you will be asked to
create a custom password for the system.
Local system and remote connectivity (LAN & Internet) user name and password:
• Username: admin
• Password: 000000
Default ports for DDNS remote access:
• Port 80 (HTTP port)
• Port 35000 (Client port)
5.9.1 Remote Connectivity
This system features remote connectivity, allowing you to view security video from any-
where in the world using our exclusive apps for smartphones, tablets and computers. Our
cloud service allows you to connect to your system over the Internet via a secure hand-
shake with our servers. This means you can easily connect to your system without requir-
ing any network configuration.
For details on setting up your system to connect to the Internet:
• See 15 Connecting to Your System Over the Internet on PC or Mac, page 75.
OR
• See 17 Connecting to your System Using Smartphone or Tablet Apps, page 106.
Connectivity using Lorex’s free DDNS service is also available, but requires the ports listed
above to be port forwarded on your router.
#LX400060; r.37992/37992; en-US 10

Basic Setup (DV700FS Series)
5
5.10 Quick Access to System Information
To quickly open a window that displays vital system information:
• Right-click to open the Quick Menu and click Info. Enter the system user name (default:
admin) and password (default: 000000).
OR
• Press the button on the front panel.
OR
• Press the ENTER button on the remote control.
NOTE
The QR code shown in the System Info screen can be scanned during mobile setup to enter the sys-
tem’s Device ID.
5.11 Connecting Cameras
5.11.1 Camera Compatibility
This system is compatible with 1080p MPX, 720p HD, and analog cameras. For a list of
compatible cameras, please visit www.lorextechnology.com/support.
5.11.2 About Lorex MPX Cameras
Lorex MPX cameras transmit high-definition video over BNC cable (such as RG59). They
use analog signals and can transmit video signals over long cable runs.
Lorex MPX cameras use a proprietary analog standard that only works with Lorex MPX
DVRs. MPX is not compatible with HD-SDI equipment.
5.11.3 Installing Cameras
CAUTION
Cameras differ in terms of installation or mounting instructions. Please see the documentation that came
with your camera(s) for specific installation instructions.
Installation Tips
• Test the cameras before permanent installation. Plan where you will route the wiring for
the camera and where you will aim the camera.
• Mount the camera where the lens is away from direct and intense sunlight.
• Plan your cable wiring so that it does not interfere with power lines or telephone lines.
• Ensure that the camera wiring is not exposed or easily cut.
• Mount the camera in an area that is visible, but out of reach.
#LX400060; r.37992/37992; en-US 11

Basic Setup (DV700FS Series)
5
• Avoid pointing the camera at a glass window to see outside. This may result in a bright
white ring in the night vision image, as the light from the night vision LEDs may reflect
off the glass.
• Adjust the camera angle so that it covers an area with high traffic.
• In "high-risk" locations, have multiple cameras point in the same area. This provides
camera redundancy if a vandal attempts to damage the camera.
To install the cameras:
1. Mount the camera(s) to the desired mounting surface according to the instructions that
came with the camera(s). Choose a firm mounting surface.
NOTE
If you wish to mount cameras to drywall, it is recommended to use drywall anchors (not included).
2. Adjust the camera stand to ensure that the camera has a satisfactory view of the area
you would like to monitor. Stand configuration depends on the mounting surface you
have chosen (see below for suggested stand configurations).
Table Mount Wall Mount Ceiling Mount
NOTE
Camera model may not be exactly as shown.
5.11.4 Connecting Camera Extension Cables
CAUTION
The extension cable must be a single stretch of cable between the DVR and camera. You cannot connect
multiple extension cables to each other. For more details on extension cables, see 5.11.5 Extension Ca-
ble Options, page 13.
1. Connect the male power connector on the BNC extension cable to the female power
connector on the camera.
• Connect the BNC connector to the camera.
2. Connect the female power connector on the BNC extension cable to the power
adapter.
3. Connect the BNC connector to one of the Video Input ports on the rear panel of the
DVR.
4. Plug the camera power adapter to a power outlet.
#LX400060; r.37992/37992; en-US 12