FLORABEST FAT 18 B3 User manual

®
IAN 273039
CORDLESS GRASS TRIMMER FAT 18 B3
AKKU-RASENTRIMMER
Originalbetriebsanleitung
CORDLESS GRASS TRIMMER
Translation of the original instructions
BATTERIDREVEN GRÆSTRIMMER
Oversættelse af den originale driftsvejledning
COUPE-BORDURES SANS FIL
Traduction des instructions d‘origine
ACCUGRASMAAIER
Vertaling van de originele gebruiksaanwijzing
273039_flo_Akku-Rasentrimmer_cover_DK_BE.indd 2 02.09.15 10:04

GB / IE Translation of the original instructions Page
DK Oversættelse af den originale driftsvejledning Side
FR / BE Traduction des instructions d‘origine Page
NL / BE Vertaling van de originele gebruiksaanwijzing Pagina
DE / AT / CH Originalbetriebsanleitung Seite
Before reading, unfold the page containing the illustrations and familiarise yourself with all functions of the
device.
Før du læser, vend siden med billeder frem og bliv bekendt med alle apparatets funktioner.
Avant de lire le mode d‘emploi, ouvrez la page contenant les illustrations et familiarisez-vous ensuite avec
toutes les fonctions de l‘appareil.
Vouw vóór het lezen de pagina met de afbeeldingen open en maak u vertrouwd met alle functies van het
apparaat.
Klappen Sie vor dem Lesen die Seite mit den Abbildungen aus und machen Sie sich anschließend mit allen
Funktionen des Gerätes vertraut.
273039_flo_Akku-Rasentrimmer_cover_DK_BE.indd 3 02.09.15 10:04

1
2
3
4
5
6
7
8
9
10
11
1312
14
15
16
16
17
20
16 19
19
18
17
16
24

4
GB IE
Content
Introduction .................................4
Intended purpose.........................4
General description......................5
Extent of the delivery....................... 5
Overview ...................................... 5
Functional description ..................... 5
Technical data..............................5
Safety instructions........................ 6
Symbols and icons.......................... 6
General safety instructions for power
tools ............................................. 7
Charging the battery.................. 12
Removing / inserting the
battery ........................................ 12
Recharging the battery.................. 12
Used batteries.............................. 13
Assembling instructions.............. 13
Operation ................................14
Turning on and off ........................ 14
Checking the battery charge level... 14
Trimmer settings............................ 14
Manner of operation..................15
Cutting grass................................ 15
Vertical cut / lawn edge
trimming...................................... 15
Cleaning and maintenance.........16
Cleaning ..................................... 16
General maintenance.................... 16
Replacing the cutting insert ............ 16
Storage...................................... 16
Replacement parts/Accessories ..17
Trouble shooting ........................17
Disposal and protection of
the environment.........................18
Guarantee .................................18
Repair Service............................19
Service-Center............................20
Importer .................................... 20
Introduction
Congratulations on the purchase of your
new device. With it, you have chosen a
high quality product.
During production, this equipment has
been checked for quality and subjected
to a nal inspection. The functionality of
your equipment is therefore guaranteed. It
cannot be ruled out that residual quantities
of water or lubricants will remain on or in
the equipment/hose lines in isolated cases.
This is not a fault or defect and it repre-
sents no cause for concern.
The operating instructions constitute part of
this product. They contain important infor-
mation on safety, use and disposal.
Before using the product, familiarise your-
self with all of the operating and safety
instructions. Use the product only as de-
scribed and for the applications specied.
Keep this manual safely and in the event
that the product is passed on, hand over
all documents to the third party.
Intended purpose
The appliance is solely intended for cutting
grass and weeds in the garden and for
edge trimming. Any other use that is not
specically approved in these Instructions
can result in damage to the trimmer and
give rise to serious danger for the user. Do
not use the appliance to trim hedges or
bushes. The appliance must only be used
by adults. Young people aged 16 and
over may only use the trimmer under adult
supervision.
Translation of the original
EC declaration of conformity ......92
Exploded Drawing .....................97

5
GB IE
12 Cutting disk
13 Cutting insert
14 Protective cover
15 Bar for tilt angle adjustment
16 Battery
17 Battery release button
18 Battery charge state indicator
19 Battery charger
20 Guide track
21 Handle holder
22 Handle screw
23 Pin
24 Twist lock
Functional description
The trimming assembly of the manually
controlled, portable, battery-operated
lawn trimmer consists of a system of plastic
knife/cutting insert.
The appliance also features a pivoting mo-
tor head, adjustable aluminium telescopic
shaft, and a spacer bow. A hood covering
the cutting device protects the user.
The following describes the functions of the
operating parts. This equipment is not suit-
able for commercial use.
Commercial use will invalidate the guar-
antee.
Technical data
Appliance
Motor voltage.......................... 18 V
Idling speed ...............8000 min-1 (rpm)
Protection Class ............................... III
Protection category ...................... IP20
Runtime..........................max. 50 min*
Cutting circle .............................25 cm
Weight (without battery charger) ... 2.1 kg
The user or operator is responsible for ac-
cidents causing injury to other people or
damage to property.
The manufacturer cannot be held liable
for damage when the trimmer is not used
in conformity with its intended purpose or
due to incorrect operation.
General description
Extent of the delivery
Carefully unpack the trimmer and check
that it is complete:
- Battery-operated lawn trimmer
- Cutting disc
with one srew (left-hand thread)
- Protective cover with three screws
- Auxiliary handle
- 20 Cutting inserts
- Battery charger
- Battery
- Instruction Manual
The illustrations are on the front
fold-out page.
Overview
1 Top handle
2 On/Off switch
3 Switch lock
4 Box for cutting inserts
(not visible)
5 Auxiliary handle
6 Handle rod
7 Lock of handle rod adjustment
8 Threaded bush for length adjust-
ment
9 Telescopic shaft
10 Motor head
11 Spacer bow (ower guard)

6
GB IE
Sound pressure level
(LpA).................72.8 dB (A), KpA= 3 dB
Sound power level (LWA)
guaranteed .......................94 dB (A)
measured.... 83,8 dB (A); KWA=2.21 dB
Vibration (ah)
upper handle.1.098 m/s2, K=1.5 m/s2
additional handle
..................... 1.539 m/s2, K=1.5 m/s2
Battery (Li-Ion)
Nominal voltage...................... 18 V
Capacity..................................1.5 Ah
Charging time ...................approx. 5 h
Recharger ............ JLH122100400G
Nominal consumption................. 15 W
Uptake voltage / Input
...................... 100-240 V~, 50/60 Hz
Voltage output / Output 21 V 400 mA
Protection class ............................ II
Protection category ...................... IP20
* The actual runtime under load of a fully
charged battery depends on how you
work and on the load put on the trimmer
during operation.
Noise and vibration values have been
determined according to the standards
and regulations mentioned in the declara-
tion of conformity. The vibration and noise
measuring processes in accordance with
EN 786, appendices D and E, were com-
pleted successfully.
Noise and vibration values have been
determined according to the standards and
regulations mentioned in the declaration of
conformity.
Technical and optical changes may be
undertaken in the course of further devel-
opment without notice. All dimensions,
references and information in this instruc-
tion manual are therefore not guaranteed.
Legal claims made on the basis of the
instruction manual can therefore not be
considered as valid.
The stated vibration emission value was
measured in accordance with a standard
testing procedure and may be used to com-
pare one power tool to another.
The stated vibration emission value may
also be used for a preliminary exposure
assessment.
Warning: The vibration
emission value may differ during
actual use of the power tool from
the stated value depending on the
manner in which the power tool is
used.
Safety precautions aimed at protect-
ing the user should be based on esti-
mated exposure under actual usage
conditions (all parts of the operating
cycle are to be considered, includ-
ing, for example, times during which
the power tool is turned off and
times when the tool is turned on but
is running idle).
Safety instructions
Ensure that the safety instructions are ob-
served when operating the trimmer.
Symbols and icons
Symbols on the trimmer
WARNING!
Carefully read these Operating In-
structions.
Wear goggles and ear defenders.

7
GB IE
After turning off the appli-
ance, the cutting disk will
keep revolving for a couple
of seconds. Keep away
from your hand and feet.
Do not expose the trimmer to mois-
ture. Do not work when it is raining
and do not cut wet grass.
Keep by-standers well
away. They could be in-
jured by ung out objects.
Remove the battery prior to servic-
ing the appliance.
Noise level rating LWA in dB
Electrical appliances must not be dis-
posed of with the domestic waste.
Cutting circle
Symbols on the battery
Do not dispose of
batteries in house-
hold waste, re or
water.
Do not subject the battery to
strong sunlight over long periods
and do not leave it on a heater
(max. 45°C).
Take batteries to an old battery
collection point where they will
be recycled in an environmentally
friendly manner.
Symbols on the recharger
WARNING!
Before using for the rst time, care-
fully read through the user manual
The recharger is for indoor use
only.
T2A
130°C
Miniature fuse
Protection class II
Electrical appliances must not be dis-
posed of with the domestic waste.
Symbols in the manual
Warning symbols with in-
formation on damage and
injury prevention.
Instruction symbols (the instruction is
explained at the place of the excla-
mation mark) with information on
preventing damage.
Help symbols with information on
improving tool handling.
General safety instructions for
power tools
WARNING! Read all safety
directions and instructions.
Omissions in the compliance with
safety directions and instructions
can cause electrical shock, re
and/or severe injuries.

8
GB IE
Retain all safety directions and in-
structions for future use.
The term “Power Tools” used in the safety
instructions refers to mains-operated power
tools (with power cord) and to battery-oper-
ated power tools (without power cord).
1) WORK AREA SAFETY
a) Keep work area clean and well
lit. Cluttered or dark areas invite acci-
dents.
b) Do not operate power tools in
explosive atmospheres, such as
in the presence of ammable
Iiquids, gases or dust. Power tools
create sparks which may ignite the dust
or fumes.
c) Keep children and bystanders
away while operating a power
tool. Distractions can cause you to lose
control.
2) ELECTRICAL SAFETY
a) Power tool plugs must match the
outlet. Never modify the plug in
any way. Do not use any adapter
plugs with earthed (grounded)
power tools. Unmodied plugs and
matching outlets will reduce risk of electric
shock.
b) Avoid body contact with earthed
or grounded surfaces, such as
pipes, radiators, ranges and re-
frigerators. There is an increased risk
of electric shock if your body is earthed
or grounded.
c) Do not expose power tools to rain
or wet conditions. Water entering a
power tool will increase the risk of electric
shock.
d) Do not abuse the cord. Never use
the cord for carrying, pulling or
unplugging the power tool. Keep
cord away from heat, oil, sharp
edges or moving parts. Damaged
or entangled cords increase the risk of
electric shock.
e) When operating a power tool
outdoors, use an extension cord
suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the
risk of electric shock.
f) If operating a power tool in a
damp location is unavoidable,
use a residual current device
(RCD) protected supply. Use of an
RCD reduces the risk of electric shock.
3) PERSONAL SAFETY
a) Stay alert, watch what you are
doing and use common sense
when operating a power tool. Do
not use a power tool while you
are tired or under the inuence
of drugs, alcohol or medication.
A moment of inattention white operating
power tools may result in serious personal
injury.
b) Use personal protective equip-
ment. Always wear eye protec-
tion. Protective equipment such as dust
mask, non-slip safety shoes, hard hat, or
hearing protection used for appropriate
conditions will reduce personal injuries.
c) Prevent unintentional starting.
Ensure the switch is in the off-po-
sition before connecting to power
source and/or battery pack,
picking up or carrying the tool.
Carrying power tools with your nger on
the switch or energising power tools that
have the switch on invites accidents.
d) Remove any adjusting key or
wrench before turning the power
tool on. A wrench or a key left attached

9
GB IE
to a rotating part of the power tool may
result in personal injury.
e) Do not overreach. Keep proper
footing and balance at all times.
This enables better control of the power
tool in unexpected situations.
f) Dress properly. Do not wear loose
clothing or jewellery. Keep your
hair, clothing and gloves away
from moving parts. Loose clothes,
jewellery or long hair can be caught in
moving parts.
g) If devices are provided for the
connection of dust extraction and
collection facilities, ensure these
are connected and properly used.
Use of dust collection can reduce dust-
related hazards.
h) Never let children or persons who are not
familiar with the instructions mentioned
use the machine.
i) Stop using the machine when persons,
above all children, and house pets are in
the vicinity.
j) Use the machine only in daylight or with
good articial lighting.
k) Always keep your hands and feet away
from the cutting equipment, above all
when you switch the motor on.
l) Never install metallic cutting elements.
m) Before commissioning and after any im-
pacts, check for signs of wear and dam-
ages, and have any necessary repairs
performed.
n) Never use the machine with damaged or
missing protective equipment.
4) POWER TOOL USE AND CARE
a) Do not force the power tool. Use
the correct power tool for your
application. The correct power tool will
do the job better and safer at the rate for
which it was designed.
b) Do not use the power tool if the
switch does not turn it on and off.
Any power tool that cannot be controlled
with the switch is dangerous and must be
repaired.
c) Disconnect the plug from the
power source and/or the bat-
tery pack from the power tool
before making any adjust -ments,
changing accessories, or storing
power tools. Such preventive safety
measures reduce the risk of starting the
power tool accidentaIly.
d) Store idle power tools out of the
reach of children and do not al-
low persons unfamiliar with the
power tool or these instructions to
operate the power tool. Power tools
are dangerous in the hands of untrained
users.
e) Maintain power tools. Check for
misalignment or binding of mov-
ing parts, breakage of parts and
any other condition that may af-
fect the power tool’s operation. If
damaged, have the power tool repaired
before use. Many accidents are caused
by poorly maintained power tools.
f) Keep cutting tools sharp and
clean. Properly maintained cutting tools
with sharp cutting edges are less Iikely to
bind and are easier to control.
g) Use the power tool, accessories
and tool bits etc. in accordance
with these instructions, taking into
account the working conditions
and the work to be performed.
Use of the power tool for operations dif-
ferent from those intended could result in
a hazardous situation.
h) Ensure that the vents are free of soiling.

10
GB IE
5) CAREFUL HANDLING AND USE OF
BATTERY DEVICES
a) Charge the batteries only in
chargers that are recommended
by the manufacturer. Risk of re if a
charger that is suitable for a specic type
of battery is used with other batteries.
b) In the power tools, use only the
batteries designed for the pur-
pose. The use of other batteries may
result in injuries and risk of re.
c) Keep the unused battery away
from paper clips, coins, keys,
nails, screws and other small
metal objects, which could cause
bridging of the contacts. A short
circuit between the battery contacts may
cause burns or re.
d) If used incorrectly, liquid may
leak from the battery. Avoid
contact with this. In the event of
accidental contact, rinse off with
water. If the liquid gets into eyes,
seek medical assistance. Leaking
battery uid may cause skin irritations or
burns.
6) SERVICE
Have your power tool serviced by
a qualied repair person using
only identical replacement parts.
This will ensure that the safety of the
power tool is maintained.
7) SPECIAL SAFETY DIRECTIONS FOR
BATTERY-OPERATED TOOLS
a) Ensure that the device is switched
off before inserting the battery.
Inserting a battery into a power tool that
is switched on may result in accidents.
b) Recharge the batteries indoors
only because the battery charger
is designed for indoor use only.
c) To reduce the electric shock haz-
ard, unplug the battery charger
from the mains before cleaning
the charger.
d) Do not subject the battery to
strong sunlight over long periods
and do not leave it on a heater.
Heat damages the battery and there is a
risk of explosion.
e) Allow a hot battery to cool before
charging.
f) Do not open up the battery and
avoid mechanical damage to the
battery. Risk of short circuit and fumes
may be emitted that irritate the respiratory
tract. Ensure fresh air and seek medical
assistance in the event of discomfort.
g) Do not use non-rechargeable bat-
teries!
8) CORRECT HANDLING OF THE BAT-
TERY CHARGER
• This appliance is not intended for opera-
tion by persons (including children) with
reduced physical, sensory or mental
capabilities, or lacking experience and/
or knowledge, unless they are under the
supervision of or have been instructed on
how to use the appliance by a person
responsible for their safety.
• Keep the equipment away from children
and pets. Children should be supervised
in order to ensure that they do not play
with the equipment.
•To charge the battery, use only
the charger supplied.
Risk of re and explosion. This ensures
that the safety of the device is maintained.
•Before each use, check the charg-
er, cable and plug and have them

11
GB IE
repaired by qualied profession-
als and only with original parts.
Do not use a defective charger and do
not open it up yourself. This ensures that
the safety of the device is maintained.
•Connect the charger only to a
socket with an earth. Ensure that
the mains voltage matches the
specications on the charger rat-
ing plate. Risk of electric shock.
•Disconnect the charger from the
mains before closing or opening
connection to the battery / power
tool / device.
•Keep the charger clean and away
from wet and rain. Do not use
the charger outdoors. Dirt and the
entry of water increase the risk of electric
shock.
•Operate the charger only with
the appropriate original batteries.
Charging other batteries may result in
injuries and risk of re.
•Avoid mechanical damage to the
charger. This can result in internal short
circuits.
•Do not operate the charger on a
combustible surface (e.g. paper,
textiles). Risk of re due to heating dur-
ing charging.
• If the power cable for this equipment is
damaged, it must be replaced by the
manufacturer, a customer service agent of
the same or a similarly qualied person in
order to prevent hazards.
• The battery of the appliance is not fully
charged at the time of delivery. It there-
fore needs to be fully recharged before
you use it for the rst time. For the rst
recharge cycle we recommend that you
charge the battery for about 1 hour. Slot
the battery into the base and plug the bat-
tery charger into a mains outlet.
• When the battery is fully charged, unplug
the charger from the mains and from the
appliance. Charging time is approx. 1
hour.
• Do not charge the battery continuously
since this may damage the battery cells.
Note: Repeatedly charging small capaci-
ties may damage the battery cells. Re-
charge the battery only if the appliance is
becoming slow.
• Do not use the charger to charge non-
rechargeable batteries.
9) RESIDUAL RISKS
Even if properly operating and handling this
electric tool, some residual risks will remain.
Due to its construction and build, this electric
tool may present the following hazards:
a) Cuts
b) Ear damage if working without ear pro-
tection.
c) Damage to your health caused by swing-
ing your hands and arms when operating
the appliance for longer periods of time
or if the unit is not held or maintained
properly.
Warning! During operation, this elec-
tric tool generates an electromagnetic
eld which, under certain circum-
stances, may impair the functionality
of active or passive medical implants.
To reduce the risk of serious or lethal
injuries, we recommend that persons
with medical implants consult their
doctor and the manufacturer of their
medical implant before operating the
machine.

12
GB IE
Charging the battery
Do not expose the battery to
extreme conditions such as
heat or impact. Risk of injury
from escaping electrolytic so-
lution! After eye/skin contact,
rinse the affected areas with
water or a neutraliser and
consult a doctor.
Charge the battery in a dry room
only.
Prior to attaching the charger, check
that the battery‘s outer surface is
clean and dry.
There is a risk of injury due to elec-
tric shock.
Only use the original charger from
the package to charge the battery.
Mind not to charge the appliance
for more than 5 hours at a time. If
you do, the battery and the appli-
ance may be damaged and longer
charging times would be a waste
of energy. Excessive charging will
void the warranty.
• Charge the battery before the rst
time of use. Do not briey charge
the battery several time in a row.
• Recharge the battery when you no-
tice that the appliance is becoming
slower.
• If a fully recharged battery lasts
for considerably shorter operating
times, the battery is used up and
needs to be replaced. Only use an
OEM spare battery available from
our Customer Service.
• Always take heed of the applicable
safety instructions as well as the en-
vironmental protection regulations
and information.
• The warranty excludes all defects
caused by improper handling.
Removing / inserting the
battery
1. To remove the battery (16) from
the appliance, press the release
button (17) on the battery and
pull out the battery.
2. To insert the battery (16), place
it on the guide track (20) and
push it back into the appliance.
It will audibly snap in.
Do not insert the battery until
the appliance is fully assem-
bled. Risk of injury!
Recharging the battery
Recharge the battery ( 16) when the
last charge state indicator LED ( 18)
lights up red.
One LED at the charging status indi-
cator ( 18) of the battery ( 16)
LED ashes green during the char-
ging process. A green LED for each
preloaded section of the batteries
( 16). If all three LED‘S of the indi-
cating charging status ( 18) lights
up green, the battery ( 16) is fully
charged.
1. Remove the battery (16) from the
appliance, as necessary.
2. Inser the battery (16) in the char-
ging compartment of the battery
charger (19). It will audibly snap
in.
3. Plug the battery charger (19)
into a mains outlet.

13
GB IE
on the motor head (10). If the
position is correct, the cross-head
screw on the pipe is no longer
visible.
4. To lock, turn the twist lock (24)
approx.45º clockwise. Lock closed
symbol .
To put on the protective
cover:
1. Place the protective cover (14) on
the motor head (10) and screw it
down with the 3 Phillips screws.
To put on the auxiliary
handle:
2. Pull the ends of the auxiliary
handle (5) to extend the handle
and slide it over the handle
holder (22). The storage box for
your plastic knife (4) must point
upwards.
3. Screw down the screw (23) in the
auxiliary handle (5).
Mounting the trimming unit:
4. Slip the cutting disc (12) onto the
axle. There is only one mount-
ing position. Screw the cutting
disc (12) to the axle. Mind the
left-hand thread. Please ensure
that the screws are properly tight-
ened.
Place the cutting insert (13) on
the pin (23) on the cutting disk
(12) and pull out the insert until it
snaps in.
Spare cutting inserts are kept in the
box (4) on the auxiliary handle (5).
4. When the battery is fully rechar-
ged unplug the battery charger
(19) from the mains.
5. Press the release button ( 17)
on the battery (16) and pull the
battery out of the battery char-
ger (19).
Used batteries
• If a fully recharged battery lasts for
considerably shorter operating times,
the battery is used up and needs to be
replaced. Only use an OEM battery
pack replacement available from our
Customer Service.
• Always take heed of the applicable
safety instructions as well as the envi-
ronmental protection regulations and
information (see “Cleaning and Main-
tenance”).
Assembling instructions
Do not insert the battery until
the appliance is fully assem-
bled. Risk of injury!
To put together the equip-
ment:
1. Turn the black twist lock (24) on
the motor head (10) until the
notches match up to those in the
green casing. Lock open symbol
.
2. When plugging in the telescopic
tube (9) be aware of the different
plastic pin thicknesses on the
tube. Only one position is possi-
ble.
3. Plug the end of the telescopic
tube (9) all the way into opening

14
GB IE
To insert the battery:
5. To insert the battery (16), place it
on the guide track (20) and push
it into the appliance. It will audi-
bly snap in.
Operation
Caution: risk of injury! Do not
operate the appliance with-
out the protective cover. To
operate the appliance, wear
suitable clothing, eye and ear
protection.
Prior to every use, check that
the appliance is operative. Do
not block the On/Off switch
or the switch lock. They must
reliably turn off the motor
when you release the switch.
Do not operate the appliance
if one of the switches is dam-
aged.
Please observe local regulations
concerning noise protection.
Turning on and off
Maintain a rm stand and hold the
appliance well with both hands and
at some distance away from your
body. Before turning on the appli-
ance, check that it will not touch
any objects.
1. Check that the battery (16) is in
(see “Assembly instructions - In-
serting the battery”).
2. To turn on, use your thumb to
actuate the switch lock (3), then
press the On/Off switch (2). Re-
lease the switch lock.
3. To turn off, release the On/Off
switch (2). There is no continuous
operation mode.
After turning off the appli-
ance, the trimming assembly
will keep revolving for some
time. Allow the trimming as-
sembly to come to a stand-
still. Neither touch nor slow
down the moving cutting in-
sert. Risk of injury!
Checking the battery charge
level
The battery’s ( 18) charge level is indi-
cated by the charge state indicator (
16).
Press the PRESS button on the battery.
The LEDs indicate the battery’s charge
level.
one green LED = battery low
two green LED = charging about half
three green LED = battery fully charged
red LED = charging the battery
Trimmer settings
To adjust the auxiliary handle:
The auxiliary handle can be set to various
positions. Adjust the handle such that the
cutting disk slightly tilts forward in your
working position.
Loosen the screw (23) in the handle
and move the auxiliary handle (5) to
your favourite position. Tighten the
screw in the handle.

15
GB IE
To adjust the height:
The telescopic shaft allows you to adjust
the appliance to your personal size.
Loosen the threaded bush
(8). Adjust the telescopic shaft (9)
to the correct length and tighten the
threaded bush.
To adjust the cutting angle:
Changing the cutting angle lets you trim
grass at places that a difcult to reach,
e.g. under benches or wall offsets.
Tread on the pedal (15) on the motor
housing and tilt the telescopic shaft
(9). There are 6 preset tilt angles (see
“Work instructions”).
To adjust the handle rod:
The handle rod can be turned by 90° and
180° (see “Work instructions”).
Push down the lock (7) and turn the
handle rod
0° 90° 180°
(6) until it
snaps into your favourite position.
To adjust the spacer bow (ower
guard):
The spacer bow keeps the trimming as-
sembly away from plants and trunks not to
be cut.
Push the spacer bow (11) forward.
When the spacer bow is not in use you
can move it back to its parking posi-
tion.
Manner of operation
WARNING. Danger of in-
jury!
• Do not cut moist or wet grass.
• Prior to starting the appliance,
check that the cutting disk does
not contact stones, gravel or other
foreign bodies.
• Switch on the trimmer before you
approach the grass that is to be
cut.
• Do not overload the trimmer dur-
ing operation.
• Avoid contact with obstacles
(stones, walls, fences, etc.) as this
will rapidly wear out the lines.
Cutting grass
Cut the grass by
swaying the trimmer
sideways to the right
and left. Cut slowly
while the trimmer is
tilted forwards by
approx. 30°.
Cut tall grass by a
series of levels from top to bottom.
Vertical cut / lawn edge
trimming
Be particularly careful and
attentive when operating the
cutter vertically. To avoid in-
juries, keep enough distance
to the trimming assembly.
Setup for vertical trimming:
Move the appliance to the right and
left in a slow swinging motion to
trim slopes and steep inclines.
• Handle rod: 180° (see )
• Cutting angle: 0° (see )
• Spacer bow in parking position

16
GB IE
Setup for edge trimming:
To trim lawn edges, slowly move the
appliance along the lawn edges.
• Handle rod: 90° (see )
• Cutting angle: 90° (see )
• Spacer bow in parking position
Cleaning and
maintenance
Contact our Service Centre about
repairs and servicing not described
in this manual. Only use OEM
parts. Risk of injury!
Turn off the appliance and, before
doing any servicing, remove the
battery.
The following cleaning and servicing
should be done regularly. This will ensure
a long and reliable service life.
Cleaning
Do not spray the appliance
with water and do not im-
merse it in water. Electric
shock hazard!
• Keep clean the ventilation slots, motor
housing and handles of the appliance.
Use a damp cloth or a brush.
Do not use cleaning agents or solvents.
You may otherwise irreparably dam-
age the appliance.
• After every trimming session, remove
grass and soil from the protective cover
and the trimming assembly.
• To thoroughly clean the trimming as-
sembly, remove the cutting insert
(13) (see “Replacing the cutting
insert”) and use a sharp knife to clean
the pin ( 24).
General maintenance
• Prior to every use, check the appliance
for obvious defects such as loose, worn
or damaged parts.
Check that the screws in the cutting
disk are tight.
• Check covers and safety devices for
damages and correct installation. Re-
place as necessary.
Replacing the cutting insert
1. Slide the cutting insert (13) in-
ward and push it out of the pin
(24) on the cutting disk (12).
2. Place the new cutting insert (13)
on the pin (24) and pull out the
insert until it snaps in.
Storage
• Store the trimmer in a dry place well
out of reach of children.
• Do not stand the trimmer on its pro-
tective cover. Suspend it by its upper
handle in such a manner that the pro-
tective cover does not come into con-
tact with other objects. This is because
the protective cover could become
deformed, thereby changing its dimen-
sions and its safety properties.
• In order to keep the battery well
charged, avoid exposing the appli-
ance to extreme heat or cold in stor-
age.
• Remove the battery before storing the
unit for longer periods of time.

17
GB IE
Replacement parts/Accessories
Spare parts and accessories can be obtained at
www.grizzly-service.eu
If you do not have internet access, please contact the Service Centre via telephone
(see “Service-Center” page 20). Please have the order number mentioned below ready.
Cutting inserts (pack of 20) ......................................................................91099379
Battery...................................................................................................91099411
Battery charger.......................................................................................91099412
Trouble shooting
Problem Possible cause Corrective action
Appliance won‘t
start
Battery ( 16) discharged Recharge battery ( 16) (see „Charg-
ing“)
Battery ( 16) not in Insert battery ( 16) (see „Operation“)
On/Off switch ( 2) de-
fective Send in to Service Centre for repair
Motor defective
Intermittent opera-
tion
Internal loose contact
Send in to Service Centre for repair
On/Off switch ( 2) de-
fective
Much vibration
Loud noise
Cutting insert ( 13) bro-
ken Replace cutting insert ( 13) (see „Cleaning and servicing“)
Trimming assembly dirty Clean trimming assembly (see „Cleaning
and servicing“)
Motor defective Send in to Service Centre for repair
Bad trim
Cutting insert ( 13) bro-
ken Replace cutting insert ( 13) (see „Cleaning and servicing“)
Trimming assembly dirty Clean trimming assembly (see „Cleaning
and servicing“)
Battery ( 16) not fully
charged Recharge battery ( 16) (see „Charg- ing“)

18
GB IE
Disposal and protection
of the environment
Remove the battery from the device and
take the device, battery, accessories and
packaging for environmentally friendly
recycling.
Machines do not belong with domes-
tic waste.
Do not dispose of batteries in
household waste, re (risk of explo-
sion) or water. Damaged batteries
may damage the environment and
your health if toxic fumes or liquids
leak out.
• Return the unit to a recycling centre.
The plastics and metals in the unit can
be sorted and appropriately recycled.
Ask our Service Centre for details.
• Dispose of batteries in discharged condi-
tion. We recommend covering the pole
with adhesive tape to prevent a short
circuit. Do not open up the battery.
• Dispose of batteries in accordance with
the local regulations. Take batteries to
an old battery collection point where
they will be recycled in an environ-
mentally friendly manner. For informa-
tion about this, ask your local waste
management company or our service
centre.
• Defective units returned to us will be
disposed of for free.
• Throw the cut grass on the compost. Do
not throw it in the normal household
waste.
Guarantee
Dear Customer,
This equipment is provided with a 3-year
guarantee from the date of purchase.
In case of defects, you have statutory rights
against the seller of the product. These
statutory rights are not restricted by our
guarantee presented below.
Terms of Guarantee
The term of the guarantee begins on the
date of purchase. Please retain the original
receipt. This document is required as proof
of purchase.
If a material or manufacturing defect
occurs within three years of the date of
purchase of this product, we will repair or
replace – at our choice – the product for
you free of charge. This guarantee requires
the defective equipment and proof of pur-
chase to be presented within the three-year
period with a brief written description of
what constitutes the defect and when it oc-
curred.
If the defect is covered by our guarantee,
you will receive either the repaired product
or a new product. No new guarantee pe-
riod begins on repair or replacement of the
product.
Guarantee Period and Statutory
Claims for Defects
The guarantee period is not extended by
the guarantee service. This also applies for
replaced or repaired parts. Any damages
and defects already present at the time of
purchase must be reported immediately af-
ter unpacking. Repairs arising after expiry
of the guarantee period are chargeable.

19
GB IE
Guarantee Cover
The equipment has been carefully pro-
duced in accordance with strict quality
guidelines and conscientiously checked
prior to delivery.
The guarantee applies for all material and
manufacturing defects. This guarantee
does not extend to cover product parts
that are subject to normal wear and may
therefore be considered as wearing parts
(e.g. cutting inserts) or to cover damage to
breakable parts (e.g. battery, charger, cut-
ting plate, protective housing, switches).
This guarantee shall be invalid if the prod-
uct has been damaged, used incorrectly or
not maintained. Precise adherence to all of
the instructions specied in the operating
manual is required for proper use of the
product. Intended uses and actions against
which the operating manual advises or
warns must be categorically avoided.
The product is designed only for private
and not commercial use. The guarantee
will be invalidated in case of misuse or
improper handling, use of force, or inter-
ventions not undertaken by our authorised
service branch.
Processing in Case of Guarantee
To ensure quick handling of you issue,
please follow the following directions:
• Please have the receipt and item num-
ber (IAN 273039) ready as proof of
purchase for all enquiries.
• Please nd the item number on the rat-
ing plate.
• Should functional errors or other de-
fects occur, please initially contact the
service department specied below by
telephone or by e-mail. You will then
receive further information on the pro-
cessing of your complaint.
• After consultation with our customer
service, a product recorded as defec-
tive can be sent postage paid to the
service address communicated to you,
with the proof of purchase (receipt)
and specication of what constitutes
the defect and when it occurred. In or-
der to avoid acceptance problems and
additional costs, please be sure to use
only the address communicated to you.
Ensure that the consignment is not sent
carriage forward or by bulky goods,
express or other special freight. Please
send the equipment inc. all accessories
supplied at the time of purchase and
ensure adequate, safe transport pack-
aging.
Repair Service
For a charge, repairs not covered by the
guarantee can be carried out by our ser-
vice branch, which will be happy to issue
a cost estimate for you.
We can handle only equipment that has
been sent with adequate packaging and
postage.
Attention: Please send your equipment to
our service branch in clean condition and
with an indication of the defect.
Equipment sent carriage forward or by
bulky goods, express or other special
freight will not be accepted.
We will dispose of your defective devices
free of charge when you send them to us.

20
GB IE
Service-Center
Service Great Britain
Tel.: [phone]
(£ 0.10/Min.)
E-Mail: [email protected]
IAN 273039
Importer
Please note that the following address
is not a service address. Please initially
contact the service centre specied above.
Grizzly Tools GmbH & Co. KG
Stockstädter Straße 20
63762 Großostheim
Germany
www.grizzly-service.eu