FLOS RF04322 User manual

EN
11
RF04322
BJB E27 LAMP HOLDER
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061

12
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
Fig.1
Fig.2
L
H
RF04322
BJB E27 LAMP HOLDER
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061
M
I
N
Remove the white glass diffuser.
It is necessary to ask somebody to hold the glass
diffuser (I).
Unlock the rod (L) from the housings (M) present on
the diffuser assembly (I).
Remove the glass diffuser (I) by unhooking the lamp
holder supports from the housing (H).
Remove the lamp-bulb.

13
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
Unfasten the 2 screws (A) of the cable clamp
present on the lamp holder assembly and then
remove the cover (B).
Fig.3
Fig.4
A
B
RF04322
BJB E27 LAMP HOLDER
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061

14
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
Remove the lamp holder (E) that needs to be
replaced, from the cap (F) and from the lamp
holder assembly support (G).
Assemble now the new spare-part:
Insert the new lamp holder (E) inside the cap (F)
and lamp holder support (G).
REMARK!!! Ensure that the terminals of the lamp
holder correspond with the holes present on the
cap.
Fig.5
Fig.6
C
F
D
Insert a thin pin (C) or any other similar object
inside the terminals (D) of the wire connections.
Press down inside the terminals (D) with the pin (C)
and then free the wires from the lamp lamp holder.
E
G
RF04322
BJB E27 LAMP HOLDER
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061

15
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
Strip-off 15mm length of the wires isolations.
Fig.6
Fig.7
Strip-off 40mm length of the electrical isolation.
CABLE ISOLATION
ISOLANTE CAVO
40 mm
15 mm
WIRE ISOLATION
ISOLANTE CONDUTTORI
RF04322
BJB E27 LAMP HOLDER
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061

16
WARNING! When installing and whenever acting on the appliance, ensure that the power supply has been switched off.
For the installation of the spare-part, it is necessary to consult a qualified electrician.
©2021 Flos -All rights reserved -www.flos.com
Flos reserves the right to introduce any changes to its own models, without prior notice.
EN
Twist and bend the conductors (K) of the wires and
connect them inside the terminals (D) of the lamp
holder.
Verify that they are inserted correctly by pulling
the wires.
Clamp the electrical cable.
Position the cable clamp cover (B) and fasten the 2
screws (A).
Now Insert the lamp bulb.
Install the bulb-holder in its housing (H) present on
the glass diffuser (I).
Insert the rod (L) in the housing (M).
Hook the rod (L) into the housing (N), up to the
blocking “click”. (view image at page 12)
Fig.7
Fig.8
D
A
K
RF04322
BJB E27 LAMP HOLDER
REV. 1
DATE 01/07/2021
GLO-BALL S2 F3010061