Flowserve Accord WS/WM Ultraswitch User manual

USER INSTRUCTIONS
Installation
Operation
Maintenance
FCD ACENIM0135-02 - 09/16
Accord WS/WM Ultraswitch™
Switchbox

2
1. GENERAL INFORMATION .................................................................................... 3
2. SAFETY INSTRUCTION....................................................................................... 3
3. UNPACKING.................................................................................................... 3
4. CERTIFICATES................................................................................................. 4
5. SPECIFICATIONS.............................................................................................. 4
5.1 Technical data .................................................................................................................................4
5.2 Materials of construction ................................................................................................................4
5.3 Product label...................................................................................................................................4
5.4 WS/WM UltraSwitch™ nomenclature..............................................................................................5
5.5 WS/WM UltraSwitch™ switch options ............................................................................................6
6. INSTALLATION ................................................................................................ 8
6.1 Wiring instructions .........................................................................................................................9
6.2 Cover and housing options ...........................................................................................................10
7. SWITCHES (Certified) ....................................................................................... 11
7.1 Installation in hazardous locations................................................................................................11
7.2 Adjusting limit switches................................................................................................................ 11
7.3 Cam fine adjustment ....................................................................................................................11
7.4 Switch option specifications (all) ..................................................................................................12
8. DIMENSIONS ................................................................................................. 14
9. SPARE PARTS ................................................................................................ 15
10. SPECIAL CONDITIONS FOR SAFE USE .................................................................. 15
CONTENTS
FCD ACENIM0135-02 - 09/16

3
1. GENERAL INFORMATION
WS/WM Ultraswitch™ enclosures provide local and remote position indication for
automated valves. They generally feature a visual black/yellow or red/green indicator for
intuitive local position determination. The WS/WM Ultraswitch™ is available with a number
of limit switch options for remote indication, in a variety of electrical applications. They may
also be used as a junction box for direct installation of solenoid valves.
2. SAFETY INSTRUCTION
Read the safety instructions in this manual carefully before using the product. If any
questions arise during installation, contact supplier/sales office before continuing further.
This equipment is suitable for use in Class 1, Division 1&2, groups ABCDFG or non-hazardous locations
only.
3. UNPACKING
Report transport damage to the carrier immediately. In case of discrepancies - contact your
nearest FLOWSERVE location.
• Substitution of components may impair suitability
for Div. 2 locations.
• Inspect periodically for degradation. Replace parts if
degradation is found.
• Cleaning this housing by rubbing should be done in
a non-hazardous area.
• Potential electrostatic charging hazard, clean only
with a damp cloth – danger of propagating discharge.
• All grounding and bonding installation requirements
must be addressed.
• Pay attention to personal protection, (clothing,
glasses, gloves) when performing installation or
service.
• All installation, inspection, and maintenance of the
equipment should be performed by suitably trained
personnel. For more information refer to EN 60079-
14:1997, EN 60079-17, EN 60079-18, EN 60079-19.
• Do not disconnect equipment unless area is known
to be non-hazardous.
• To prevent ignition of flammable or combustible
atmospheres, disconnect power before servicing.
• Use only Flowserve original spare parts in order not
to invalidate certification.
WARNING
POTENTIAL ELECTROSTATIC HAZARD
DO NOT OPEN WHEN AN EXPLOSIVE ATMOSPHERE MAY BE PRESENT
CABLE ENTRANCES MAY REACH A TEMPERATURE OF MAX 83 ºC
SEE MANUAL FOR SAFE USE
CERTIFICATES, MANUAL AND CONTROL DRAWING CAN BE DOWNLOADED FROM
WWW.PMV.NU
FCD ACENIM0135-02 - 09/16

4
4. CERTIFICATES
General Purpose
ATEX II 1GD Ex ia IIC T4/T5/T6
ATEX II 1GD Ex ia IIB T4/T5/T6
cCSAus Class I, Division 1 Groups A,B,C,D; Class II Division 1 Groups F,G; Class III
cCSAus Class I, Division 2, Groups A,B,C,D; Class II, Division 2, Groups F,G; Class III
5. SPECIFICATIONS
5.1 Technical data
Ingress protection IEC 529 IP 66/67, NEMA Type 4X Weight (max) 0.7 kg / 1.55 lbs
5.2 Materials of construction
Part Material
Housings Powder Epoxy painted Aluminum or
PA6/PA66 engineered resin, 25 – 30% fiberglass filled
Covers Powder Epoxy painted Aluminum or
PA6/PA66 engineered resin, 25 – 30% fiberglass filled or
Transparent Polycarbonate
Shaft Stainless Steel SS EN 2346 / AISI 303
Cams/Splines Nylon
Terminal Block Nylon
Internal Brackets Nylon, Aluminum or Stainless Steel
All Internal Fasteners Stainless Steel
All External Fasteners Stainless Steel
All Molded in Fasteners Anodized Aluminum
Indicators Polycarbonate or PA66
5.3 Product label
Product name and model code
Warnings Year of manufacture
Manufacturer
Electrical rating
and diagram
Serial number
Logotype
Approvals
* NOTE: If the equipment is likely to come in contact with aggressive
substances, it is the responsibility of the user to take suitable precautions
to prevent it from being adversely affected, thus ensuring that the type of
protection provided by the equipment is not compromised.
FCD ACENIM0135-02 - 09/16

5
5.4 WS/WM UltraSwitch™ nomenclature
A = brand, NAMUR shaft, 1/2” NPT Housing with 2 conduits, Aluminum body, Resin cover, stadard UltraDome™,
2 proximity switches ”PP”, cCSAus certificate (2 open terminals)
FCD ACENIM0135-02 - 09/16
A = Brand sticker
A Accord
B = Shaft type
N Namur shaft, EN 15714
S Low profile shaft
T For NAF Turnex
D Double ”D” 1/4 Inch Flats
C = Body style
WS General Purpose/I.S. Enclosure / 1/2” NPT Conduit entries
WM General Purpose/I.S. Enclosure / M20x1,5mm Conduit entries
D = Number of conduit entries
2 2 conduit entries
4 4 conduit entries (2 according to ”C” + entries opposite side with different type of th-
reading)
E = Body material
A Aluminum
R Engineered resin
F = Cover material
A Aluminum
R Engineered resin
P Polycarbonate Cover (clear)
G = Indicator
1 No indicator
2 Flat Arrow Indicator Yellow / Black
H Black / Yellow UltraDome™
U Standard UltraDome™ (Red Close/Green Open)
H = Number of switch elements
0 No switches (empty housing)
1 1 Switch
2 2 Switches
I = Switch type - (See page 12 and 13)
J = Certificate
14 General Purpose
15 ATEX Ex ia
28 cCSAus Ni
Ordering code example
A B C C D E F G H I I J J
A N W S 2 A R U 2 P P 2 8

6
5.5 WS/WM UltraSwitch™ switch options
More switch options available
FCD ACENIM0135-02 - 09/16
Cert. Switch Option Manufacturer Load Capacity
M1 SPDT Mechanical Honeywell
MicroSwitch
15A @ 125/250 VAC; 0,5A @ 125 VDC; 0,25A @
250VDC; 5A @ 120VAC (resistive load)
MG A, B SPDT Gold Mechanical Honeywell
MicroSwitch
1A @ 125 VAC; 50 mA @ 24 VDC
(resistive load)
F1 IN5129 IFM 10-36VDC
F3 IF5250 IFM 10-36VDC NC PNP, 150mA, 3-wire NC
F5 IF6001 IFM 18-32VDC, NO PNP, 150mA@50°C
F6 IF6034 IFM 10-36VDC, NO PNP, 150mA, Stainless
steel
F7 IN0074 IFM 20-250 AC/DC NO, 350mA/100mA
F8 IN0081 IFM 20-250 AC/DC NO, 350mA/100mA w/LED
FJ IN5263 IFM IN-2002-FRKG/PH RT
P4 A, B, C SPST Proximity Aleph 0.35A @ 140 VAC; 0.25A @ 200VDC
(50 W Max.)
P5 A, B, C SPDT Proximity Hamlin 0.25A @ 120 VAC; 0.25A @ 28 VDC
(3 W Max.)
PE A, B, C SPDT Sabre Proximity Flowserve 1A @ 120 VAC; 1A @ 24 VDC
PP C SPDT Phazer Proximity Flowserve 3A @ 120 VAC; 2A @ 24 VDC
PT A, B, C SPST BRS Proximity Flowserve 3A @ 120 VAC; 0.5 @ 24 VDC
N8 A Solid State Proximity PF NJ2 V3 N NAMUR NC Sensor; 8 VDC
NP A Solid State Proximity PF SJ3.5-N NAMUR Sensor Output; 5-25 VDC Supply
NQ A Solid State Proximity PF NJ4-12GK-N NAMUR NC Sensor; 8 VDC
NR Solid State Proximity PF NJ4-12GM40-E1 PNP Sinking; 200 mA max.
Current; 10-60 VDC
NS Solid State Proximity PF NJ4-12GM40-E2 NPN Sourcing; 200 mA max.
Current; 10-60 VDC
NT Solid State Proximity PF NJ4-12GK40-E2 NPN Sourcing; 200 mA max.
Current; 10-60 VDC
N9 Solid State Proximity PF NBB3-V3-Z4 NPN Sourcing; 100 mA max.
Current; 5-60 VDC
NW A Solid State Proximity PF SJ3.5-SN NAMUR NC Sensor; 8 VDC

7
Notes
1) Valid certification codes according to table in WS/WM Nomenclature on page 5.
2) Some models have more than two open terminal locations open as standard. Consult factory for details.
Code Certificate
A ATEX II 1GD Ex ia IIC T4/T5/T6
ATEX II 1GD Ex ia IIB T4/T5/T6
B cCSAus IS
C cCSAus NI
FCD ACENIM0135-02 - 09/16

8
WS/WM switch mounted on rotary actuator
ISO/NAMUR
Mounting bracket
VDI/VDE 3845
Hex. screws
4x M5x8
Mounting kits
For compact/low profile installation - use mounting kit KL01 or KL02. Use with shaft type ”S” only. These
kits allow the user to install it on actuators with a shaft height of 20, 30 or 50mm. The kits also adapt
easily to both 80/30mm actuator top pattern as well as 130/80mm actuator top pattern (see table below
for reference). Standard NAMUR mounting brackets are also available.
The WS/WM Ultraswitch™ may be installed to
valves or valve actuators with a variety of mounting
hardware.
For best results, specify the NAMUR shaft option
and NAMUR mounting hardware when fitting to a
NAMUR compliant actuator. These options allow
direct coupling to actuators without couplings,
reducing dead band.
Bolt bracket to actuator and WS/WM
Ultraswitch™ to bracket, leaving bolts finger tight.
For NAMUR applications the WS/WM Ultraswitch™
switch shaft features an integral alignment pin.
This pin must engage the tapped hole in the
actuator shaft.
For non-NAMUR applications, make sure to
properly install a coupler between the WS/WM
Ultraswitch™ and actuator. Once the WS/WM
Ultraswitch™ is installed with fasteners loosely
tightened, stroke the actuator two or three times
to align the bracket. Then tighten all fasteners.
Ambient temperature working conditions.
The WS/WM Ultraswitch™ switch box is tested
and operational in following temperature range:
-40° – 180°F
-40° – 80°C
Note! Shaft type ”S”
only!
c
KL01 20/30 yes yes 80/90
KL02 50 yes yes 110
Mounting kit p/n Actuator shaft height (mm) Bolt pattern 80/30 (mm) Bolt pattern 130/30 (mm) C = Height (mm)
6. INSTALLATION
FCD ACENIM0135-02 - 09/16

9
6.1 Wiring instructions
• Perform all wiring according to the
wiring diagram found on the label
in the housing (see picture) and
instructions given below.
• Make sure that the ground wire is
correctly connected
• Seal unused entries with proper and
suitable conduit plugs.
The WS/WM Ultraswitch™ enclosures feature
pre-wired switches. All user connections are made
at a numbered terminal strip. Both external and
internal grounding locations have been provided
for use in installation. A wiring diagram is located
on the product label and indicates which terminal
number corresponds to which switch contact:
normally open, normally closed, common, etc.
Follow the wiring diagram, and electric code to
connect switches to your system.
For field wiring: ensure that any excess wire lengths
or loops are routed away from any moving parts
and are short enough, or secured to ensure a 1/4”
clearance between the wire and the inside surface
of the switchbox cover.
Note: for all magnetically tripped proximity swit-
ches, the top switch should only be used to indicate
the clockwise position: the bottom switch should
only be used to indicate the counter-clockwise
position. Any deviation from these settings may
result in erratic indication.
Solenoids may also be wired through the WS/WM
Ultraswitch™ enclosure. At least two auxiliary
terminals are included as standard. Wire the so-
lenoid to auxiliary terminals, then connect power
leads to the opposite terminal side. Be sure to
properly ground the solenoid at the provided
ground terminal.
WS UltraSwitch™ Series enclosures include two
1⁄2” NPT conduit entries and the WM Series inclu-
des two M20x1.5 conduit entries.
Caution!
• Proper and suitable conduit plugs must be
installed in unused conduit entries before put-
ting the unit into service.
• Installation must be according to National
Electric Code, local codes, local certificates
and manufacturer’s instructions in all cases.
Environmental seals must be used to protect
ingress of water through the conduits.
• Prevent electrostatic build-up for safe use. The
enclosure of the WS/WM Ultraswitch™ switch
box is made of PA6/PA66 and any impact or
friction caused by external objects should be
avoided to prevent electrostatic build-up.
Wiring diagram inside
Internal and external grounding
Terminal strip
FCD ACENIM0135-02 - 09/16

10
Aluminum or Resin
cover
Dome Indicator
Aluminum housing Resin housing
Aluminum or Resin
cover
Arrow Indicator
Polycarbonate transparent cover
Arrow Indicator
Polycarbonate transparent cover
Dome Indicator
Aluminum or Resin
cover flat
6.2 Cover and housing options
FCD ACENIM0135-02 - 09/16

11
Substitution of components may impair suitability for hazardous (classified) locations. Do
not disconnect equipment unless area is known to be non-hazardous.
To prevent ignition of flammable or combustible atmospheres, disconnect power before ser-
vicing, or; read, understand and adhere to the manufacturer’s live maintenance procedures.
7. Switches (certified)
7.2 Adjusting limit switches
UltraSwitch™ enclosures feature Quick-Set™ cams
which are used to trip the limit switches. These
cams are easily adjusted without tools.
Caution: disconnect power before removing cover
when installed in hazardous locations.
Remove cover and set aside. Rotate actuator/valve
to full clockwise (CW) position. Adjust cam(s) as-
sociated with CW as follows:
1. Push or pull cam against spring to disengage
it from splines.
2. Rotate cam CW breaking contact with switch
(or moving magnet away from switch).
3. Continue rotating cam CW just until switch
trips.
4. Release cam and re-engage it with splines.
Rotate actuator/valve to full counter-clockwise
(CCW) position. Adjust cam(s) associated with
CCW as described in steps 1 through 4, except
Cam adjustment
7.1 Installation in hazardous locations
Refer to control drawing RA-2. Consult factory.
rotate cam(s) CCW.
Note: factory setting is:
Top switch = CW (closed)
Second switch = CCW (open)
Cam fine adjustment
7.3 Cam fine adjustment
Some cams have a fine adjustment available. These
cams will have a small screw embedded in the side
of the cam.
Adjusting this screw clockwise or counter clock-
wise will deform the cam, changing the trip point
slightly.
FCD ACENIM0135-02 - 09/16

12
00 No switches
(empty housing)
F1 IFM IN5129 10-36VDC (J=14only)
F3 IFM IF5250 10-36VDC NC PNP, 150mA, 3-wire NC
F5 IFM IF6001 18-32VDC, NO PNP, 150mA@50°C
F6 IFM IF6034 10-36VDC, NO PNP, 150mA, Stainless Steel
F7 IFM IN0074 20-250 AC/DC NO, 350mA/100mA
F8 IFM IN0081 20-250 AC/DC NO, 350mA/100mA w/LED (J=14)
F9 IFM IN0097 20-250 AC/DC NO FB
IFM IF5249 10-36VDC NO PNP, 150mA, 3-wire NO
FC IFM IF5718 10-36VDC NO PNP/NPN, 150mA, plastic
FE IFM NS5003 IS-2002-N
FG IFM IS5070 FB3004-APKG
FH IFM IS5001 IS-3002-BPOG
FJ IFM IN5263 IN-2002-FRKG/PH RT
FK IFM NS5002 IS-2002-N
FZ AS-i Bus Card 31VDC 28 mA
M1 SPDT Honeywell V7-1C13D8-201 15.1A (1/2 HP) at 125/250 VAC; 1/4A at 125 VDC;
Mechanical MicroSwitch 1/4A at 250 VDC; 5A at 120 VAC (resistive load)
MG SPDT Honeywell V7-1D19D8-201 1A at 125 VAC / 50 mA at 24 VDC
Gold Mechanical MicroSwitch (resistive load)
N1 Pepperl+Fuchs NJ4-12GM40-E
N2 Pepperl+Fuchs NJ2-12GK-N
N3 Pepperl+Fuchs SJ3,5-S1N
N4 Pepperl+Fuchs NJ2-12GK-SN
N5 Pepperl+Fuchs NJ4-12GK40-E
N6 Pepperl+Fuchs NJ4-12GK40-E1
N7 Pepperl+Fuchs NBB2-V3-E0
N8 Solid State Proximity Pepperl+Fuchs NJ2-V3-N NAMUR Sensor Output / 5-25 VDC Supply
N9 Solid State Proximity Pepperl+Fuchs NBB3-V3-Z4 NPN Sourcing/ 100 mA max. Current / 5-60 VDC
NA Pepperl+Fuchs NBN4-12GM40-E2
NB Pepperl+Fuchs NJ2-12GM-N
NC Pepperl+Fuchs NJ4-12GM-N
ND Pepperl+Fuchs NCB2-12GM40-Z1
NE Pepperl+Fuchs NCB2-12GM35-N0
NF Pepperl+Fuchs NCN4-12GM35-N0
NG Pepperl+Fuchs NJ5-11-N-G
NH Pepperl+Fuchs NCB4-12GM40-N0
NK Pepperl+Fuchs NCN4-12GM40-Z0
NL Pepperl+Fuchs NCB2-V3-N0
NM Pepperl+Fuchs NJ2-11-SN-G
NN Pepperl+Fuchs NBB2-V3-E2
NP Solid State Proximity Pepperl+Fuchs SJ3.5-N
NQ Solid State Proximity Pepperl+Fuchs NJ4-12GK-N
NR Solid State Proximity Pepperl+Fuchs NJ4-12GM40-E1 PNP Sinking / 200 mA max. Current / 10-60 VDC
7.5 Switch option specifications (all)
Code Switch Option Manufacturer Part Number Load Capacity
FCD ACENIM0135-02 - 09/16

13
7.5 Switch option specifications (continued)
NS Solid State Proximity Pepperl+Fuchs NJ4-12GM40-E2 NPN Sourcing / 200 mA max.
Current / 10-60 VDC
NT Solid State Proximity Pepperl+Fuchs NJ4-12GK40-E2 NPN Sourcing / 200 mA max.
Current / 10-60 VDC
NV Solid State Proximity Pepperl+Fuchs NJ2-11-N-G NAMUR Sensor Output / 5-25 VDC Supply
NW Solid State Proximity Pepperl+Fuchs SJ3,5-SN NAMUR Sensor Output / 5-25 VDC Supply
NX NBB2-V3-E3
NY Solid State Proximity Pepperl+Fuchs NJ4-12GK-SN NAMUR Sensor Output / 5-25 VDC Supply
P4 SPST Proximity Aleph PS-6132 0.35A at 140 VAC / .25A at 200VDC
(50 W Max.)
P5 SPDT Proximity Hamlin 59135-030 0.25A at 120 VAC / 0.25A at 28 VDC (3 W Max.)
PE SPDT Sabre Pxy Flowserve XA0199 1A at 120 VAC / 1A at 24 VDC
PP SPDT Phazer Pxy Flowserve XA0155 3A at 120 VAC / 2A at 24 VDC
PT SPST BRS Pxy Flowserve XA0157 3A at 120 VAC / 0.5 at 24 VDC
R1 Pepperl+Fuchs NBB3-V3-Z4-3G-3D
R2 Pepperl+Fuchs NBB2-V3-E3-3G-3D
R3 Pepperl+Fuchs NBN4-V3-E2-3G-3D
Code Switch Option Manufacturer Part Number Load Capacity
FCD ACENIM0135-02 - 09/16

14
8. Dimensions
WS body enclosure WM body enclosure
FCD ACENIM0135-02 - 09/16

15
9. Spare parts
10. Special Conditions for Safe Use
Pos Part No Description
1 D2-SP31 Arrow indicator assembly
2 D2-SP52 Dome indicator assembly
red/green
2 D2-SP17 Dome indicator assembly
black/yellow
3 M800214 Polycarbonate transparent cover
with dome indicator red/green
4 M800215 Polycarbonate transparent cover
with arrow indicator
5 ME1967 Gasket for cover
(all cover types)
1
2
3
4
5
• The Rotary Limit Switch Box is marked with the following warning marking: ”WARNING – POTENTIAL
ELECTROSTATIC CHARGING HAZARD – SEE INSTRUCTIONS”.
• Enclosure material limits for EPL Ga are exceeded, as aluminium content is greater than 10%. User
must determine the suitability of the equipment for the particular application, for example, to avoid an
ignition hazard due to impact or friction
• The total electrical ratings must not exceed the values indicated in the control drawing, W-43C.
FCD ACENIM0135-02 - 09/16

Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
Country Name
Town Name, City 00000 Country
Telephone: [phone]
To find your local Flowserve representative please use
the Sales Support Locator System found at
www.flowserve.com
Or call toll free: 0 000 000
To find your local Flowserve representative:
Bulletin XX-00-00 (X)
This area can be used for divisional information
Flowserve Corporation has established industry leadership in the design and manufacture of its products. When properly selected, this Flowserve
product is designed to perform its intended function safely during its useful life. However, the purchaser or user of Flowserve products should be aware
that Flowserve products might be used in numerous applications under a wide variety of industrial service conditions. Although Flowserve can provide
general guidelines, it cannot provide specific data and warnings for all possible applications. The purchaser/user must therefore assume the ultimate
responsibility for the proper sizing and selection, installation, operation, and maintenance of Flowserve products. The purchaser/user should read and
understand the (INSERT OFFICIAL USER INSTRUCTION TITLE) instructions included with the product, and train its employees and contractors in the
safe use of Flowserve products in connection with the specific application.
While the information and specifications contained in this literature are believed to be accurate, they are supplied for informative purposes only and
should not be considered certified or as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be construed as a
warranty or guarantee, express or implied, regarding any matter with respect to this product. Because Flowserve is continually improving and upgrading
its product design, the specifications, dimensions and information contained herein are subject to change without notice. Should any question arise
concerning these provisions, the purchaser/user should contact Flowserve Corporation at any one of its worldwide operations or offices.
For more information about Flowserve Corporation, contact www.flowserve.com or call USA 1-800-225-6989.
To find your local Flowserve representative:
To find your local Flowserve representative please use the Sales
Support Locator System found at www.flowserve.com
Flowserve Corporation has established industry leadership in the design and manufacture
of its products. When properly selected, this Flowserve product is designed to perform its
intended function safely during its useful life. However, the purchaser or user of Flowserve
products should be aware that Flowserve products might be used in numerous applications
under a wide variety of industrial service conditions. Although Flowserve can provide general
guidelines, it cannot provide specific data and warnings for all possible applications. The
purchaser/user must therefore assume the ultimate responsibility for the proper sizing and
selection, installation, operation, and maintenance of Flowserve products. The purchaser/user
should read and understand the (WS/WM Switchbox User Instructions) instructions included
with the product, and train its employees and contractors in the safe use of Flowserve products
in connection with the specific application.
While the information and specifications contained in this literature are believed to be accurate,
they are supplied for informative purposes only and should not be considered certified or
as a guarantee of satisfactory results by reliance thereon. Nothing contained herein is to be
construed as a warranty or guarantee, express or implied, regarding any matter with respect
to this product. Because Flowserve is continually improving and upgrading its product design,
the specifications, dimensions and information contained herein are subject to change without
notice. Should any question arise concerning these provisions, the purchaser/user should
contact Flowserve Corporation at any one of its worldwide operations or offices.
For more information about Flowserve Corporation, contact www.flowserve.com or call USA
1-800-225-6989.
© October 2013, Flowserve Corporation, Irving, Texas
FCD ACENIM0135-02 - 09/16
Flowserve Corporation
Flow Control Division
1978 Foreman Drive
Cookeville, Tennessee 38501 USA
Phone: [phone]
Fax: [phone]
Flowserve Flow Control (UK) Ltd.
44 Victoria Way, Burgess Hill
West Sussex, RH15 9NF
UNITED KINGDOM
Tel: [phone]
E-mail: pmvuksales@flowserve.com
Flowserve Flow Control Benelux
Rechtzaad 17
4703 RC Roosendaal
THE NETHERLANDS
Tel: [phone]
Fax: [phone]
E-mail: fcbinfo@flowserve.com
Flowserve Flow Control GmbH
Rudolf-Plank Strasse 2
D-76275 Ettlingen
GERMANY
Tel: [phone]
Fax: [phone]
E-mail: argus@flowserve.com
Flowserve Spa
Via Prealpi, 30
20032 Cormano (Milano)
ITALY
Tel: [phone]
Fax: [phone]
E-mail: infoitaly@flowserve.com
Flowserve Ahaus GmbH
von-Braun-Str. 19a
48683 Ahaus
Phone: [phone]
Fax: [phone]
Flowserve Corporation
No. 35, Baiyu Road
Suzhou Industrial Park
Suzhou 215021, Jiangsu Province,
PRC
Phone: [phone]
Fax: [phone]
Flowserve Australia Pty Ltd
Flow Control Division
14 Dalmore Drive
Scoresby, Victoria 3179
Austrialia
Phone: [phone]
Fax: [phone]
Flowserve Pte Ltd
No. 12 Tuas Avenue 20
Singapore 638824
Phone: [phone]
Fax: [phone]
Flowserve do Brasil Ltda
Rua Tocantins, 128 - Bairro Nova
Gerti
São Caetano do Sul,
São Paulo 09580-130 Brazil
Phone: [phone]
Fax: [phone] - 423
flowserve.com