Fluance RT82 User manual

RT82, RT83, RT84, RT85
Reference High Fidelity Vinyl Turntable
User Manual v2.4
Serious Performance™Fluance.com

Fluance RT82, RT83, RT84, RT85 User Manual 2
Introduction
Fluance believes everyone should experience audio in its truest form, recreating the performance
the way the artist intended. Utilizing only superior components and expert audio engineering,
their products are a testament to the performance that can be achieved when a passion for music
takes center stage. The perfect complement to any audiophile’s lifestyle, you’ll be enjoying live
performances in your home for years to come.
Fluance.com/resources Fluance.com/contactFluance.com/support
Don’t forget to register your product with us!
Fluance.com/registration
Thank you for your purchase of this Fluance®product.
We hope you enjoy your experience.
Questions?
Give us a chance to help, we’re just a click away.
Bag
Bubble Level
45 Adapter
Rubber Turntable Mat
(RT82/RT83/RT84 Only)
Dust Cover
Turntable
Headshell
with Stylus
Counterweight
Cardboard
Insert
Cardboard
Insert
Foam End Cap
Foam End Cap
Dust Cover
Hinges
Cotton
Gloves
Instruction
Manual
Motor
Pulley
Cap
Platter with
Rubber Belt
Box
Ground
Cable
Power
Adapter
RCA
Audio
Cable

Fluance RT82, RT83, RT84, RT85 User Manual 4
What’s Included
LIFETIME
Customer Support
Turntable with
Dust Cover
Motor Pulley
Cap
Manual
Dust Cover
Hinges
RCA Audio
Cable
Power
Adapter
45 Adapter
Ground Cable
Lifetime Customer
Support
Bubble Level
2 Year
Warranty
Headshell with
Stylus
RT82 - OM 10
RT83 - 2M Red
RT84/RT85 - 2M Blue
RT85N – MP-110
Platter with
Rubber Belt
RT82/RT83/RT84 - Metal
RT85 - Acrylic
Rubber
Turntable Mat
RT82/RT83/RT84 Only
RT85 - Mat Not Included
Counterweight

Fluance RT82, RT83, RT84, RT85 User Manual 5
Components and Connections
1
2
4
3
5
6
7
8
14
21
20
18 19
15
16 17
13
12
11
10
9
1. Platter
2. Motor Pulley
3. Motor Pulley Cap
4. Rubber Belt
5. Spindle
6. Rubber Turntable Mat
(RT82/RT83/RT84 Only)
7. Speed Selection
8. Power LED
9. Counterweight
10. Anti-Skating Control
11. Cueing Lever
12. Tonearm Lock
13. Tonearm
14. Headshell & Stylus
15. RCA Audio Outputs
16. Ground Terminal
17. Auto Stop Switch
18. Power Input
19. Motor Servo
20. Isolation Feet
21. Hinge

Fluance RT82, RT83, RT84, RT85 User Manual 6
1. Remove the protective packaging and
ensure the turntable is placed on a
sturdy and level surface. Place the
platter onto the spindle located in the
middle of the turntable.
2. Place the motor pulley cap over the
motor pulley. Ensure the arrows are
aligned so that the motor pulley cap
is installed properly.
Tip: The arrows help to align the notch on the
motor cap with the post on the motor.
3. Lift the rubber belt and place it around
the motor pulley. Rotate the platter
several times to ensure the rubber belt
is secure and not twisted.
4. RT82/83/84: Place the turntable mat
on top of the platter. Make sure the
logo side is facing up
Note: RT85-Turntable mat is not included. When
using an acrylic platter a turntable mat is not required.
Turntable Mat
Platter
Motor Pulley Cap
Spindle
Motor Pulley
First Time Setup
Step One: Installing the Platter

Fluance RT82, RT83, RT84, RT85 User Manual 7
Step Two: Installing the Counterweight
Step Three: Installing the Headshell
1. Secure the tonearm using the
tonearm lock.
1. Remove the headshell from the
protective packaging and insert
into the end of the tonearm.
2. Slide the counterweight onto the end
of the tonearm with numbers facing
forward until it clicks and is fully
installed on the tonearm.
2. Tighten the locking nut until the
headshell is secure.
Tonearm Lock
Counterweight
Locking Nut
Headshell
Tonearm

Fluance RT82, RT83, RT84, RT85 User Manual 8
Step Four: Installing the Dust Cover
1. Important: Place dust cover on a soft surface to avoid scratching it. Install the hinges on
the provided grooves located on the back of the dust cover.
CAUTION: The hinges are spring loaded and can close with strong force. Use caution when
installing.
2. Carefully open the hinges on the dust cover and insert into the hinge mounts pre-
installed on the back of the turntable.

Fluance RT82, RT83, RT84, RT85 User Manual 9
Step Five: Leveling the Turntable
This turntable features 3 adjustable feet to ensure the turntable is level regardless of the surface
the turntable is resting upon.
Adjustable FeetBubble Level
Lower
Turntable
Raise
Turntable
Bubble Position Turntable Adjustment
Turntable is level when the bubble
is within the circle
Lower Back or Raise Front
Lower Left or Raise Right
Lower Back or Raise Front and
Lower Left or Raise Right
Use the table below with the included bubble level to adjust the feet and level the turntable.
Note: The turntable comes in the fully lowered position.

Fluance RT82, RT83, RT84, RT85 User Manual 10
Step Six: Balancing the Tonearm
Important!
Complete all steps for balancing the tonearm. Incorrect tonearm balancing can cause damage to the stylus and to your
records. For additional assistance go to www.uance.com/support to watch a tutorial video for this process.
1. Remove the stylus protector.
3. Position the tonearm over the
platter.
5. With the cueing lever now lowered, turn the entire counterweight until the tonearm is
balanced and floating horizontally when headshell is released. Do not allow the stylus to
touch the platter.
6. Set only the counterweight indicator ring to “0” on the center line while keeping the
tonearm balanced then lock the tonearm on the tonearm rest.
2. Unlock the tonearm and lift the
cueing lever.
4. Hold the headshell and lower the
cueing lever completely. Protect the
stylus from touching the platter.
Lock Cueing Lever
Tip: When balancing the tonearm make sure the cueing lever is down and the anti-skating control is set to 0.
Counterweight
Indicator Ring
Center Line
Cueing Lever

Fluance RT82, RT83, RT84, RT85 User Manual 11
Step Six (Continued): Balancing the Tonearm
7. Use the chart below to determine the recommended tracking force for your cartridge.
Rotate the entire counterweight counterclockwise until the indicator ring is set to the
correct value on the center line. (fig.1)
8. Set the anti-skating control value to match the recommended tracking force. (fig.2)
Tip: When setting the counterweight make sure you are turning the entire weight and not just the counterweight indicator ring.
Counterweight
Indicator Ring
Center Line
Model Cartridge Tracking Force Anti-Skating Value
RT82 OM 10 1.5g 1.5
RT83 2M Red 1.8g 1.8
RT84 / RT85 2M Blue 1.8g 1.8
RT85N MP-110 1.8g 1.8
(g.2)(g.1)

Fluance RT82, RT83, RT84, RT85 User Manual 12
Turntable Preamp
*Fluance PA10 shown here
OPTION 1
To Amplifier or
Powered Speakers
Ground Cable
Second Ground Cable
(Not included)
Step Seven: Connecting the RCA and Ground Cables
This turntable does not have an internal preamp so an external preamp or an amplifier with a
PHONO input must be used. Connect the RCA and ground cable to the back of the turntable
and then connect the other end to your external preamp or the PHONO input and ground
terminal on your amplifier. Ensure the cable colors are matched to the RCA connector colors.
Note: The included RCA cable is a high quality cable with a <90pF capacitance rating. For best performance it is
recommended that any other RCA connections use a similarly rated cable. The Fluance RCA cable is available at
www.uance.com/turntable-accessories
Step Eight: Connecting the Power Adapter
Ensure the power adapter is securely connected to a power outlet. Insert the power cable into
the power input on the back of the turntable. It is recommended to reconfirm with the bubble
level that the turntable is still level after setup is complete.
Important: When using an external preamp one ground cable should be connected between the turntable and the
preamp. A second ground cable (Not Included) should be connected between the preamp and the amplier/powered
speakers. Failure to connect both ground cables can result in unwanted noise/hum.
Important: The ground cable must be connected to both turntable and amplier. Failure to connect to both can result in
unwanted noise/humming.
Turntable Amplifier
OPTION 2
Important: Only use the ofcial power adapter included with your turntable.

Fluance RT82, RT83, RT84, RT85 User Manual 13
Step Nine: Playing a Record
Tip: For best audio performance the dust cover should be removed during playback.
Note: When the turntable is not in use the speed selection knob should be set to OFF to turn the turntable completely off.
The turntable setup is now complete! Enjoy your Fluance turntable. Should you require any
further assistance please visit us at www.uance.com/support for how-to videos and guides.
Break In Period
To experience the peak performance of your turntable, it is recommended to allow the cartridge
to break in. The break in period for cartridges included with Fluance turntables is 20 hours of
normal playback.
1. Lift the dust cover
2. Place a record on the spindle (use the
45 Adapter if necessary)
3. Turn the speed selection knob to the
correct RPM typically listed on your
record (Normal LP playback speed is 33
RPM)
4. Unlock the tonearm lock
5. Lift the cueing lever
6. Move the tonearm to the desired
starting point
7. Lower the cueing lever
Note: The auto stop function will take approximately 30 seconds at the end of the record before the turntable stops spinning.
Due to variances in vinyl record production some records may not work correctly with the auto stop function.
Auto Stop Function
The auto stop function is designed to extend the life of your stylus. At the end of a record,
the platter will automatically stop spinning if auto stop is enabled. This feature will also require
that the tonearm is moved over the record before the platter will start spinning at the selected
speed.
If the auto stop switch is set to the OFF position the platter will begin spinning as soon as
the speed selection knob is set to 33 or 45. To stop the record from spinning set the speed
selection knob to the OFF position.

Fluance RT82, RT83, RT84, RT85 User Manual 14
Maintenance
Replacing the Stylus
Use the chart below to ensure you replace your stylus with the correct model.
Replacement stylus and instructions are available at www.uance.com/turntable-accessories
Cartridge Connections Turntable Cartridge Specifications
Model Cartridge Stylus
RT82 OM 10 Stylus 10 E
RT83 2M Red Stylus 2M Red
RT84 / RT85 2M Blue Stylus 2M Blue
RT85N MP-110 JN-P110
Wire Channel
White Left (+)
Blue Left (-)
Red Right (+)
Green Right (-)
Supported Cartridge
Weight 5.0 to 7.5 grams
Effective Tonearm Mass
RT82 21.78 grams
RT83
27.5 grams
RT84
RT85
RT85N 21.1 grams
Overhang 19.2 mm
Effective Tonearm Length 224 mm
Headshell Cartridge Mount Half-inch Mount
Fluance Headshell Weight 9 grams
Replacing the Rubber Belt
1. With the platter installed remove the defective rubber belt from the motor pulley and platter.
2. Wrap the new rubber belt around the platter being careful to not overstretch the belt.
Ensure it is not twisted.
3. Lift the rubber belt and place it over the motor pulley.
4. Rotate the turntable several times to ensure the rubber belt is secure and not twisted.
Upgrading the Cartridge
The turntable supports the option of upgrading the cartridge. A complete cartridge
replacement guide and video are available at www.uance.com/resources
There is also a Cartridge Alignment Protractor at the end of the manual for your convenience.
OM 10 2M RED/
2M BLUE
MP-110

Fluance RT82, RT83, RT84, RT85 User Manual 15
Record Care
1. Records should be stored vertically in a dry environment away from sources of heat.
2. An anti-static brush can be used to remove dirt from the record’s grooved surface. Use
a record cleaning solution to further clean your records to ensure crystal clear playback.
3. It is important to use the cueing lever when lifting or lowering the tonearm to prevent
accidental slipping and scratching.
Turntable Care
1. Use a soft dry microfiber cloth to wipe dust from the turntable surface.
2. Keep the dust cover closed to ensure the turntable components remain dust free.
3. When cleaning the acrylic platter only use microfiber cloth to avoid scratching the surface.
Parts and Accessories
Replacement parts and turntable accessories are available at
www.uance.com/turntable-accessories
Stylus Care
1. When the turntable is not in use always keep the provided stylus protector installed to
prevent accidental damage.
2. A stylus cleaning brush can be used to remove dust and debris from the stylus.
3. Enabling the auto stop function will reduce wear and tear on the stylus by stopping the
turntable after playback is completed.
Part Number Description
PA10 High Fidelity Phono Preamp
VB52 Vinyl Record & Stylus Cleaning Kit
AP03 Frosted Acrylic Platter
BL21 Bubble Level
CA03 90pF RCA Cable
CW02 102g Counterweight
CW12 112g Counterweight
GW03 Ground Wire
HS82 RT82-RT85 Headshell with wires
PFHTDU Dust Cover
PFHTRP Rubber Turntable Mat
RB35 RT82-RT85 Rubber Belt
TA21 Cork Turntable Mat

Fluance RT82, RT83, RT84, RT85 User Manual 16
Troubleshooting
Turntable Not Spinning
• Turn the speed selection knob to 33 or 45 (power LED should light up). Lift the tonearm
over the platter and it should start spinning.
• The turntable should be connected to a known good power outlet and the power cable
should be securely inserted into the unit.
• Ensure the rubber belt is intact and hooked around the platter and the motor pulley.
No Power
• The turntable should be connected to a known good power outlet and the power
cable should be securely inserted into the unit.
• The power LED should light up when the speed selection knob is set to 33 or 45.
Wrong Speed
• Check the record label for the correct playback speed and that the speed selection knob is
set to match it. Normal LP playback speed is 33 1/3 RPM, but some play at 45 RPM.
Skipping
• Ensure the record surface is clear of dirt and debris. Also check that the record is not
warped or deformed.
• Inspect the stylus tip for built up dirt or debris. Use a stylus cleaning brush to clean if
necessary.
• Ensure the turntable is on a sturdy and level surface and properly leveled using the
adjustable feet.
• Use the instructions in step four of the first time setup instructions to confirm the tonearm
was balanced correctly and set to the correct tracking force for the included cartridge.
• Check that the anti-skating control is set to match the tracking force.
Audio Feedback
• If audio feedback occurs ensure the speakers are positioned away from the turntable.
The turntable should not be placed in front of the speakers or on the same surface as
the speakers.
• For best audio performance the dust cover should be removed during playback.
• Playback at excessive volume can cause feedback. If feedback is occurring decrease
volume or lower bass levels.
• If using an external preamp with a rumble filter, turn it on to reduce resonance feedback.

Fluance RT82, RT83, RT84, RT85 User Manual 17
Cueing Lever Not Lowering Tonearm
• Use instructions in step four of the first time setup instructions to confirm the tonearm was
balanced and set to the correct tracking force.
• Lock the tonearm and lower the cueing lever. Gently press down on the tonearm bridge until
fully lowered to reset the tonearm lowering mechanism.
Low Volume
• Check the RCA connections are correct and fully inserted. (See Step Seven)
• If the turntable is directly connected to an amplifier it must have a PHONO input.
• The turntable does not include an internal preamp so an external preamp or amplifier with
PHONO input must be used with the turntable. The Fluance High Fidelity Phono Preamp
(PA10) is designed for the Reference Series turntables and is available on www.uance.com.
Humming Sound
• Connect the ground wire to your external preamp or amplifier. If using an external
preamp ensure the second ground wire is connected from the preamp to the amplifier
/powered speakers.
• Ensure the headshell is fully tightened and secured.
• The turntable and other devices should be directly connected to a power outlet. It is
recommended to avoid power bars or extension cables.
• Ensure the speakers are positioned away from the turntable. The turntable should not
be placed in front of the speakers or on the same surface as the speakers.
Audio From Only One Channel
• Test the speakers with another device such as a CD Player or Smartphone.
• Confirm the tonearm is balanced and using the correct tracking force.
• Disconnect and reconnect the RCA cables ensuring they are fully inserted.
• Try a different set of RCA cables.
• Remove the headshell from the tonearm and use rubbing alcohol on a cotton swab to clean
the contacts on the back of the headshell. Reinstall the headshell ensuring the locking nut is
tightened completely.
Need Additional Help?
• Do not return this product to the store.
• Please contact Fluance Customer Experience first, regarding any additional information on
product features, specifications or assistance with setup.
• Online web chat or Support: www.uance.com/contact
• Online support videos and guides: www.uance.com/resources

Fluance RT82, RT83, RT84, RT85 User Manual 18
Specifications
Specications RT82 RT83 RT84 RT85 RT85N
CabinetSpecications
Material MDF
Dust Cover Yes - Tinted
TurntableSpecications
Drive System Belt Drive
Motor DC Motor with Servo Controller
Motor Isolation Seven-Point Rubber Isolation with Decoupling Isolation Ring
Speed 33 1/3 RPM, 45 RPM
Platter Aluminum Acrylic
Diameter of Platter 12” (30 cm)
Auto-Stop Yes
Turntable Mat Rubber None
TonearmSpecications
Type Static Balanced, S-Type
Supported Cartridge Weight 5.0 to 7.5 grams
Counterweight Ye s
Anti-skating Adjustment Yes
Pivot Bearing Yes
Cueing Lever Yes
Material Aluminum
Tonearm Wire 36 AWG Litz Cable / 7 Strand
Effective Tonearm Mass 21.78 grams 27.5 grams 21.1 grams
Overhang 19.2 mm
Effective Tonearm Length 224 mm
Headshell Mount H-4 Bayonet Mount
CartridgeSpecications
Type Moving Magnet (MM)
Cartridge Model Ortofon
OM10
Ortofon
2M Red
Ortofon
2M Blue
Ortofon
2M Blue
Nagaoka
MP-110
Replacement Stylus Stylus 10 Stylus
2M Red
Stylus
2M Blue
Stylus
2M Blue JN-P110
Stylus 0.3 x 0.7 mil 0.4 x 0.7 mil
Cantilever Aluminum
Mount Half-inch
Frequency Range 20-22,000
Hz
20-22,000
Hz
20-25,000
Hz
20-25,000
Hz
20-20,000
Hz
Channel Separation 22 dB at 1 kHz 22 dB 25 dB 25 dB 23 dB
Channel Balance < 1.5 dB 1.5 dB 1.5 dB 1.5 dB > 1.5 dB

Fluance RT82, RT83, RT84, RT85 User Manual 19
Specications RT82 RT83 RT84 RT85 RT85N
Load Impedance/
Capacitance
47k
Ohms/200
- 500 pF
47k Ohms/150-300 pF
47k
Ohms/100
pF
Output Voltage 4.0 mV 5.5 mV 5.5 mV 5.5 mV 5.0 mV
Cartridge Weight 5 grams 7.2 grams 7.2 grams 7.2 grams 6.5 grams
Headshell Weight 9 grams
Recommended Tracking
Force 1.5 grams 1.6 - 2.0 grams 1.5 - 2.0 grams
Vertical Tracking Angle 20° 31°
RubberBeltSpecications
Thickness 0.6 mm
Width 4.5 mm
Length 915 mm
OutputSpecications
Connector RCA (Gold-plated)
Preamp No - Separate Phono Preamp Required
Phono Output 4 mV 5.5 mV 5.5 mV 5.5 mV 5.0 mV
Ground Terminal Yes
PowerSpecications
Input 100 - 240 V AC (50/60 Hz)
Output 12 V / 500 mA
Consumption 1.5 W
GeneralSpecications
Unit Dimensions ( W x H
x D ) 16.5 x 5.5 x 13.75 inches (419.1 x 139.7 x 349.25 mm)
Unit Weight 6.8 kg (14.99 lbs) 7.6 kg
(16.76 lbs)
Optimal Operating
Temperature 5°C to 35°C