Fluke i1000s Configuration guide

Manual Supplement
© 2001 Fluke Corporation. All rights reserved. Printed in U.S.A.
Manual Title: i1000s Calibration Supplement Issue: 1
Part Number: 1574933 Issue Date: 7/01
Print Date: May 2001 Page Count: 2
Revision/Date:
This supplement contains information necessary to ensure the accuracy of
the above manual. Enter the corrections in the manual if either one of the
following conditions exist:
1. The revision letter stamped on the indicated PCA is equal to or higher
than that given with each change.
2. No revision letter is indicated at the beginning of the change.

i1000s Calibration Manual Supplement
7/01 1
Change #1
On page 8, Table 4, under Recommended Model,
Replace:
Digital Multimeter Hp 3458A or equivalent
With:
Digital Multimeter Agilant 3458A or equivalent
Delete the following from Table 4,
AC/DC Shunt IET Labs-DCCS-200 0.1e- 0.1% non-inductive
Replace the entire Phase Shift section, Table 5 and Figure 3 with the following:
Phase Shift Test
To check Phase Shift performance, set up the equipment as shown in Figure 3.
1. Center the Current Probe around the coil.
2. Set the calibrator output to 1V (phase meter reference input), 1A and 50 Hz, per step 1 of Table 5.
Performance Test Steps.
3. Verify that the phase meter reading is within the “Phase in Deg” limits of Table 5.
Table 5. Performance Test Steps
i1000s
mV Output Phase in Deg.
Step Coil Range 5520A
Output
5500A
Coil
I. Prim. Freq. Min. Max. Min. Max.
1 50 turn 1 mV/A 1 A 50.0 A 50 Hz 48.5 51.5 -3.0 3.0
2 50 turn 1 mV/A 2 A 100 A 400 Hz 98.0 102.0 N/A N/A
3 50 turn 1 mV/A 4 A 200 A 60 Hz 197.0 203.0 -2.0 2.0
4 50 turn* 1 mV/A 14 A 700 A 50 Hz 692.0 708.0 -2.0 2.0
5 1 turn 10 mV/A 5 A N/A 50 Hz 44.0 56.0 -15.0 15.0
6 50 turn 10 mV/A 0.4 A 20 A 50 Hz 191.0 209.0 -10.0 10.0
7 50 turn 10 mV/A 2 A 100 A 50 Hz 975.0 1025.0 -10.0 10.0
8 1 turn 100 mV/A 0.50 A N/A 50 Hz 38.5 61.5 N/A N/A
9 1 turn 100 mV/A 2.00 A N/A 50 Hz 184.0 216.0 -15.0 15.0
10 1 turn 100 mV/A 10 A N/A 50 Hz 960.0 1040.0 -15.0 15.0
* 700 A/ 50 Hz in 1 mV/A range has a TUR of 3.3
4. Continuing to use 1V as the phase meter reference input, set the calibrator output for the remaining
steps listed in Table 5. Steps 2 and 8 do not require phase tests.
5. Verify that the phase meter readings meet the "Phase in Deg" limits for each step.

Manual Supplement i1000s Calibration
27/01
0•
123
456
789
ENTER
M
k
mVHz
FIELD
EDIT
/
+
F
OPRSTBY EARTH SCOPE
EXGRD MENU
PREV
SHIFT
RESET
CE
SETUP
REF
NEW
TC
MEAS
¡F
µ
n
p
W
dBm sec
¡C
POWER
A
MULT
x
DIV
÷
MODES
MORE
5520A
CALIBRATOR
HI
LO
TRIG
GUARD
TC
20A
NORMAL AUX SCOPE
OUT
V, , ,RTD A, -SENSE, AUX V
20V PK MAX
20V PK MAX
mV Output
Black
Red
5520A calibrator
Phase meter
1 turn coil
or
5500A/coil
Tie Aux Com and
Normal Com together
using heavy gauge
wire or bus bar.
akp03f.eps
Figure 3. Phase Check Setup
mV Output Test
1. Connect the equipment as shown in Figure 5.
2. Set the calibrator output and coil for each step of Table 5.
3. Verify that the voltmeter reading is within the “i1000S mV Output” limits of Table 5.