FMI Outland Living SUNSHINE COAST OUTDOOR LIVING PERFECTED... User manual

Model: OLSC-121
OWNER’S MANUAL
SUNSHINE COAST
MODULAR OUTDOOR FURNITURE SYSTEM
COMPONENT: CHAIR
FMI BRANDS INC.
101 - 3570 194 Street, Surrey, BC Canada V3Z 1A5 • www.outlandliving.com
USA, Canada Toll Free: 1-888-514-1663 • Tel: [phone] • Email: [e-mail]
Hours of Operation: 8:30AM - 4:00PM (Pacific Time) • Customer Service in English only
D.121.000.V1® Registered trademark of FMI Brands Inc.

En-2 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
Supplied Parts & Hardware List:
PART # DESCRIPTION QUANTITY PICTURE
1Seat Cushion 1
2Back Cushion 1
3Chair Back 1
4Front Panel 1
5Side Panel 2
6Seat Panel 1
PART # DESCRIPTION QUANTITY PICTURE
7Seat Support 4
8Foot 4
9Bracket-A 2
10 Bracket-B 2
11 ¾” Length Screws,
¼ - 20 thread 28 +1
12 1-½” Length Screws,
¼ - 20 Thread 8 +1
13 ¼ - 20 Flange Nut 4 +1
14 5/32” Hex Key Tool 1

En-3
1-888-514-1663 • WWW.OUTLANDLIVING.COM
Scissors
Required Tools (Not Supplied):
WARNING:
Improper assembly, adjustment, alteration, service or
maintenance can cause injury or property damage.
Read the Owner & Safety Manual instructions thoroughly
before assembling or servicing this product.
INSTALLER: Leave this manual with the consumer.
CONSUMER: Retain this manual for future reference.
NOTES:

En-4 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
STEP 2
On a level, non-marking surface, fasten the (2x) Side Panels to the Chair Back with (2x) Bracket-A and (8x) ¾ ” Length Screws.
Use the provided 5/32” Hex Key Tool.
a) Confirm the feet mounting holes are facing down.
b) Confirm the Side Panels are mounted flush with the sides and aligned with the bottom of the Chair Back.
c) After confirming A & B above, firmly tighten the (8x) bracket screws.
(4x) ¾” LENGTH SCREWS
(4x) ¾” LENGTH
SCREWS
(2x) SIDE PANEL
(2x) SIDE
PANEL
(2x) BRACKET-A
(2x) BRACKET-A
CHAIR BACK
IMPORTANT: During
assembly, ensure that these
holes are all facing down!
SECTION 1: ASSEMBLY
STEP 1
Unpack all parts on a level, non-marking surface.
Use scissors to open the vacuum-packed cushion bags.
Be careful not to cut the cushions.
HANDLE WITH CARE
The Sunshine Coast modular component furniture
system features high quality aluminum frames
woven with 100% new all weather HDPE resin
wicker and luxury cushions constructed with
premium materials.
ATTENTION:
The cushions will be wrinkled due to being vacuum-
packed. DON’T WORRY! The wrinkles will naturally
work themselves out. Vacuum-packing has reduced
the packing box size and is a key component of the
E-commerce shipping innovation.
SCISSORS KNIFE
ATTENTION:
Note the screw holes for
mounting the feet on the
(1x) Front Panel and (2x)
Side Panels.

En-5
1-888-514-1663 • WWW.OUTLANDLIVING.COM
SECTION 1: ASSEMBLY (continued)
STEP 3
Fasten the (1x) Front Panel to the (2x) Side Panels with (2x) Bracket-B and (8x) ¾” Length Screws.
a) Confirm the feet mounting holes are facing down.
b) Confirm the ends and bottom of the Front Panel are squarely aligned with the Side Panels.
c) After confirming A & B above, firmly tighten the (8x) bracket screws.
(1x) FRONT PANEL
IMPORTANT: During
assembly, ensure that these
holes are all facing down!
ATTENTION:
INSTALLATION OF ARM RESTS
At this point, if you have purchased Arm Rests
for your Chair or Sectional, you should now turn
to your Arm Rest Owner’s Manual for installation
instructions, before proceeding to STEP 4.
When you finish installing the Arm Rests,
return to this manual and proceed to STEP 4.
(4x) ¾” LENGTH
SCREWS
(4x) ¾” LENGTH SCREWS
(2x) SIDE PANEL
(2x) SIDE PANEL
(2x) BRACKET-B

En-6 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
SECTION 1: ASSEMBLY (continued)
STEP 5
Install the (4x) Seat Supports using (8x) ¾” Length Screws.
Ensure the ends of the wicker panels are squarely aligned.
Firmly tighten the seat support screws.
STEP 4
Flip the assembly over. Use two people to lift.
Take care not to scratch the wicker.
HEAV Y OB JECT.
TWO PERSON LIFT REQUIRED.
FLIP
OVER!
(8x) ¾” LENGTH SCREWS
(4x) SUPPORT
BRACKETS

En -7
1-888-514-1663 • WWW.OUTLANDLIVING.COM
SECTION 1: ASSEMBLY (continued)
STEP 6
Install the (4x) Feet components using the (8x) 1-½” Length Screws.
Ensure the ends of the wicker panels are squarely aligned.
Firmly tighten the feet screws.
**Reference the installation instruction diagrams below, depending on which Chair configuration you are building. **
(8x) 1-½” LENGTH
SCREWS
(8x) 1-½” LENGTH
SCREWS
INSTALL (4x) FEET HERE
INSTALL (4x) FEET HERE
INSTALL (4x) FEET HERE
INSTALL (4x) FEET HERE
MIDDLE CHAIR FOR COUCH/LOVESEAT
AND/OR SINGLE CHAIR WITHOUT ARMS
ARM CHAIR

En-8 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
SECTION 1: ASSEMBLY (continued)
STEP 7
Confirm all wicker panels are squarely aligned.
Double-check the tightness of all screws.
Ensure all screws are firmly tightened.
Flip the assembly over so that the feet are contacting the ground.
Use two people to lift.
FLIP
OVER!
HEAV Y OB JECT.
TWO PERSON LIFT REQUIRED.
MIDDLE CHAIR FOR COUCH/LOVESEAT and/or
SINGLE CHAIR WITHOUT ARMS ARM CHAIR
Note installation
location of feet!

En-9
1-888-514-1663 • WWW.OUTLANDLIVING.COM
Congratulations! Your chair is now assembled and ready for use.
Don’t worry if you have extra screws laying around, we included
extra screws for you just in case.
STEP 9
Place the Seat Cushion and Back Cushion.
1. The mesh seat cushion bottom should be facing down for water drainage;
2. The seat cushion zipper should face the back of the chair to remain hidden;
3. The back cushion zipper should face down to remain hidden.
STEP 8
Lay the Seat Panel onto the Seat Supports.
Note: For cushion support, the flat seat strap surface
should be placed on the top side, so to be in contact
with the cushion bottom.
SEAT PANEL
SECTION 1: ASSEMBLY (continued)

En -10 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
SECTION 2: SECTIONAL FASTENING
Each furniture panel has (4x) holes for assembling your modular furniture.
STEP 1A
To assemble one furniture component to another, use (4x) ¾” Long Screws and (4x) Flange Nuts. Align your components. Push the screws
through the holes in one panel, through the wicker, and through the holes in the panel on the opposite side.
TIP: USE THE HEX KEY TOOL AS A GUIDE FOR PUSHING THE SCREW THROUGH THE HOLES.
**See diagrams on next page.
(4x) SECTIONAL MOUNTING HOLES
(4x) ¾” LENGTH SCREW

E n -11
1-888-514-1663 • WWW.OUTLANDLIVING.COM
SECTION 2: SECTIONAL FASTENING (continued)
TIP: THE HEX KEY TOOL CAN BE USED AS A GUIDE TO PUSH THE SCREW THROUGH
THE HOLES IN THE WICKER PANELS.
a) Wiggle the Hex Key Tool through the gaps in the wicker between both panels;
b) Align the tip of the screw with the end of the Hex Key Tool;
c) Keeping the two metal faces in contact, retract the Hex Key Tool and guide the screw through to the other side.

En -12 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
SECTION 2: SECTIONAL FASTENING (continued)
STEP 1B
Lock together using (4x) Flange Nuts.
Tighten with the Hex Key Tool.
(4x) FLANGE NUT

En -13
1-888-514-1663 • WWW.OUTLANDLIVING.COM
SECTION 2: SECTIONAL FASTENING (continued)
Arrange the different sections together in your preferred layout.
One such layout option is shown here. There is no limit to what you can build!
Additional modular components can be ordered from www.outlandliving.com.

En -14 D.121.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
Owner & Safety Manual
®
SECTION 3: MAINTENANCE
ATTENTION:
The cushions will be wrinkled when freshly released from
the vacuum pack bags. DON’T WORRY! The wrinkles will
naturally disappear.
ATTENTION:
The furniture cushion covers are removable and
washable, but can be challenging to put back on.
When replacing the covers, smooth the cushion interior
batting to prevent lumps.
IMPORTANT!
Do NOT use petroleum based, alcohol based, flammable
or corrosive cleaning products on or near the furniture.
Doing so may destroy the wicker resin material!
If in doubt, test a small inconspicuous section first.
OUTLAND LIVING Outdoor Furniture is meant for outdoor use
and requires periodic maintenance to keep it in good condition.
The all-weather resin wicker weave is made from 100% new
high-density polyethylene. HDPE is commonly recyclable, BPA
and Phthalate free and identified as the #2 plastic resin, the same
material as milk jugs.
Should any part of the wicker furniture become soiled or dirty,
wash down with soap and water. Use a soft brush and/or
non-abrasive cloth. Use only water-based cleaners.
The furniture frame is made from durable powder coated
aluminum. Rust should not be an issue.
The screw fasteners are made from 304 stainless steel.
Routinely check fasteners to ensure they are firmly tightened.
Cover and/or store your furniture to protect it from the elements,
between seasons, or when not in use.
Ensure the seat cushion mesh is facing down for water drainage.
CUSHION CARE
• Hand Washing (with or without the cushion cover removed):
Make a lukewarm water solution with 1/4 cup mild soap and one
gallon of lukewarm water. Allow to absorb into the fabric. Lightly
stir the stain with a sponge or a very soft bristle brush. Rinse
thoroughly. Air dry. Heavier stains may need to be pre-soaked
and machine washed.
• Machine Washing: Remove the covering with caution first. All
zippers should be closed. Machine wash on the delicate cycle in
cold water with a regular dose of mild laundry detergent. Allow
the fabric to dry naturally.

En -15
1-888-514-1663 • WWW.OUTLANDLIVING.COM
1 YEAR LIMITED WARRANTY
Customers in Canada and USA
All components are warranted by the manufacturer for a period of 1 year after date of purchase by the original owner against
defects in materials and workmanship under normal use.
This warranty does NOT cover normal wear and weathering, assembly and/or maintenance OR use in a commercial application.
At FMI Brands Inc.’s sole discretion, products under warranty will be repaired and/or replaced at no charge to the customer.
Any returns sent back to FMI Brands Inc. must be sent via prepaid freight and in the original retail packaging.
Please register your OUTLAND Living product for proof of purchase and warranty at:
https://outlandliving.com/register-products/.
Registration in English only.
For more warranty information and details, please contact Customer Service at [email protected].
WARNING NOTES:
• This product is not a toy.
• Children should always be supervised when using the furniture.
• Do not jump or climb on the furniture, as it may break or tip over, causing injury or death.
• Never allow children to climb inside the furniture interior compartments as they may become trapped, and/or injury or death could occur.
• CAUTION: Pinch points!
Watch out for pinching fingers when replacing the seat panel after lifting and/or accessing the inside compartment areas.
• CAUTION: Watch for sharp edges!
If the wicker somehow gets snagged and pulls a sharp corner, you can smooth it flat using a wooden spoon.
Our Quality Control team makes every effort to catch all the small imperfections, but sometimes something slips through.
Here are some QUICK FIX Tips:
• If you happen to find a raised staple, please reset it by pushing it down.
• Exposed staples can usually be hidden by sliding the strands of wicker weave.
Periodically check under and inside the furniture compartments to clear insect or animal nests,
especially after the furniture has been covered, stored, or unused for periods of time.

En -16 D.121.000.V1
Owner & Safety Manual
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CHAIR • OLSC-121
®
FOR REPLACEMENT PARTS AND ACCESSORIES PLEASE VISIT
WWW.OUTLANDLIVING.COM
Replacement part orders can be sent by mail to the address on the cover of this booklet.
This Owner’s Manual is available as a free download from www.outlandliving.com.
STOP
DO NOT
RETURN
TO STORE
If you experience ANY problems with your Outland Furniture Set,
PLEASE DO NOT RETURN IT TO YOUR POINT OF PURCHASE!
Simply call us or send an email to [e-mail] and we will answer all
questions and/or concerns that you may have.
We take pride in our products at FMI Brands Inc. (Outland Living) and will strive to
provide excellent customer support.
FMI BRANDS INC.
101 - 3570 194 Street, Surrey, BC Canada V3Z 1A5
USA, Canada Toll Free: 1-888-514-1663
Tel: [phone]
Email: [e-mail]
Hours of Operation: 8:30AM - 4:00PM (Pacific Time)
Customer Service in English only

Model: OLSC-123
OWNER’S MANUAL
SUNSHINE COAST
MODULAR OUTDOOR FURNITURE SYSTEM
COMPONENT: CORNER UNIT
FMI BRANDS INC.
101 - 3570 194 Street, Surrey, BC Canada V3Z 1A5 • www.outlandliving.com
USA, Canada Toll Free: 1-888-514-1663 • Tel: [phone] • Email: [e-mail]
Hours of Operation: 8:30AM - 4:00PM (Pacific Time) • Customer Service in English only
D.123.000.V1® Registered trademark of FMI Brands Inc.

En-2 D.123.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CORNER UNIT • OLSC-123
Owner & Safety Manual
®
Supplied Parts & Hardware List:
PART # DESCRIPTION QUANTITY PICTURE
1Seat Cushion 1
2Back Cushion
(Long) 1
3Back Cushion
(Short) 1
4Left Corner Back 1
5Right Corner Back 1
6Seat Panel 1
PART # DESCRIPTION QUANTITY PICTURE
7Corner Front Panel
(Long) 1
8Side Panel
(Short) 1
9Seat Support
(Long) 1
10 Seat Support
(Short) 3
11 Foot (with 45 degree
angle) 1
12 Foot (Standard) 3
13 Bracket-A 2
14 Bracket-B 1
15 ¾” Length Screws,
¼ - 20 thread 24 +1
16 1-½” Length Screws,
¼ - 20 Thread 10 +1

En-3
1-888-514-1663 • WWW.OUTLANDLIVING.COM
Scissors
Required Tools (Not Supplied):
WARNING:
Improper assembly, adjustment, alteration, service or
maintenance can cause injury or property damage.
Read the Owner & Safety Manual instructions thoroughly
before assembling or servicing this product.
INSTALLER: Leave this manual with the consumer.
CONSUMER: Retain this manual for future reference.
NOTES:
PART # DESCRIPTION QUANTITY PICTURE
17 ¼ - 20 Flange Nut 4 +1
18 5/32” Hex Key Tool
(Long) 1
19 5/32” Hex Key Tool
(Short) 1

En-4 D.123.000.V1
OUTLAND LIVING ®• SUNSHINE COAST • MODULAR OUTDOOR FURNITURE SYSTEM • CORNER UNIT • OLSC-123
Owner & Safety Manual
®
STEP 2
On a level, non-marking surface, align the (2x) Corner Back sections
together, upside down, as shown. Ensure the two Corner Back
components are touching face to face and the corner joint is
square and aligned at 90 degrees.
Note the (2x) crossbar connections inside the component cavity.
Using the SHORT Hex Key Tool, install (2x) 1-½” Length Screws.
** IMPORTANT! Leave loose.
Do not fully tighten the screws yet.
(2x) CORNER BACK
*Do not fully
tighten the
screws yet!
TIP: Use the ball end of the Short Hex Key Tool to turn the
screw at the bottom of the cavity. Use the tool on an angle to
avoid hitting the wicker and frame. (Sorry that this one is so
hard to reach. After this, the assembly gets much easier!)
SECTION 1: ASSEMBLY
STEP 1
Unpack all parts on a level, non-marking surface.
Use scissors to open the vacuum-packed cushion bags.
Be careful not to cut the cushions. Keep the packing box
intact as it can be used to aid the assembly.
HANDLE WITH CARE
The Sunshine Coast modular component furniture
system features high quality aluminum frames
woven with 100% new all weather HDPE resin
wicker and luxury cushions constructed with
premium materials.
ATTENTION:
The cushions will be wrinkled due to being vacuum-
packed. DON’T WORRY! The wrinkles will naturally
work themselves out. Vacuum-packing has reduced
the packing box size and is a key component of the
E-commerce shipping innovation.
SCISSORS KNIFE
USE (2x)
1- ½ ” LENGTH
SCREWS HERE