Focal Point Durham Pine User manual

ASSEMBLY & INSTALLATION INSTRUCTIONS
All instructions must be handed to the user for
safekeeping.
Please note : Except where otherwise stated, all rights, including copy-
right in the text, images and layout of this booklet is owned by Focal
Point Fires plc. You are not permitted to copy or adapt any of the con-
tent without the prior written permission of Focal Point Fires plc.
1
Revision A - 09/17
© 2017 Focal Point Fires plc.
Focal Point Fires plc.
Christchurch, Dorset BH23 2BT
Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e : [e-mail]
MODELS COVERED BY THESE INSTRUCTIONS
DURHAM SURROUND PINE

A S S E M B L Y I N S T R U C T I O N S
2
GB IE
1.0 IMPORTANT NOTES
© 2017 Focal Point Fires plc.
Section
1.0
2.0
3.0
4.0
5.0
6.0
7.0
Contents
Important notes
Tools required
Hardware & parts list
Assembly
Installation
Cleaning/ finishing
Guarantee - terms and conditions
Page No.
2
2
2
3
5
6
6
2.0 TOOLS RE UIRED
CODE NAME FIGURE QUANTITY
A
WOOD
DOWE S
(8X30mm)
14PCS
B
WOOD
DOWE S
(8X20mm)
4PCS
C CAM OCKS
(15X12mm)
11PCS
D CAM BO TS
(5.5X30mm)
11PCS
E
WOOD
SCREW
(8X32mm) 6PCS
F
WOOD
SCREW
(8X50mm)
9PCS
G SCREWS
(8X38mm)
2PCS
3.0 HARDWARE & PARTS LIST
CODE NAME FIGURE QUANTITY
①TOP PANE 1PC
②FRONT PANE 1PC
③EFT SIDE
EG
1PC
④RIGHT SIDE
EG
1PC
⑤EFT SIDE
PANE 1PC
⑥RIGHT SIDE
PANE
1PC
⑦
SIDE
INSIDE
PANE
2PC
To ensure safe and stable installation:
1. The assembled Fire Surround must be fixed / secured to wall.
2. The wall must be sturdy and in good repair.
3. Some walls require alternative fixings (not included).
4. When drilling into the wall, check for hidden pipes and cables.
5.There are two options for construction of this surround.
A - with rebates - If you are installing this surround with a gas fire, or an electric fire where there is space in the wall to recess
the fire use parts 7 & 8, this means the laminate is up against the wall.
B - with out rebates - If using this surround with an electric fire and a flat wall do not use with rebates, instead use the spacer
frame from the fire.
Cross head screwdriver PZ2 (3 inches in length or greater)
Drill, 6mm and a 2mm suitable drill bit
Pencil
Tape measure

3.0 HARDWARE & PARTS LIST - CONTINUED
3
GB IE
© 2017 Focal Point Fires plc.
STEP 1
Insert 3x cam locks (C) into the right hand side panel (6), ensuring that the cross heads are facing outwards. So it can be tight-
ened later on. Using a cross head screwdriver, screw the 3x cam bolts (D) into the right side leg (4). Offer the side panel up to
the leg to make sure the inserts are in the correct orientation. Making sure that the cam locks are facing into the right leg and
the leg is not upside down. Next insert 2 wooden 20mm dowels (A) into the right leg, using a small amount of glue (K). With
the glue on both ends of the dowel joints, insert the right panel onto the right leg. When in the correct position, you are able
to tighten the cam locks with a PZ2 screw driver.
CODE NAME FIGURE QUANTITY
H
MIRROR
P ATES
(45X43mm)
2PCS
I
WOOD
SCREW
(6X19mm)
4PCS
J WA P UG
(6X25mm)
2PCS
K G UE
(10g)
1PCS
CODE NAME FIGURE QUANTITY
⑧
TOP
INSIDE
PANE
1PC
4.0 ASSEMBLY
Fixings Parts
A x 4 PCS 3
C x 6 PCS 4
D x 6 PCS 5
6
A
A
A
A
C
C
C
D
D
D
D
D
D③
⑤
⑥
④
To assemble the left side please follow the same method used to complete the right hand side in the section above.
C
C
C

4.0 ASSEMBLY - CONTINUED GB IE
4© 2017 Focal Point Fires plc.
STEP 2
Gently lay both legs you have prepared onto a suitable protected surface. Be extremely careful not to scratch the front edges
of the legs. DO NOT DRAG THE EGS! Make sure that the legs are lifted everytime they are moved to avoid them from being
damaged.
Now lay the left hand leg on your right and the right hand leg on your left, both facing downwards. Insert 2x 20mm dowels (B)
into the left and right hand legs. Now position the front panel (2) onto the dowel joints in the legs to ensure the legs are at
the correct distance apart. Also checking that the front panel is the correct way around. Next glue the dowels into position.
Once in you are then able to screw the 6 x32mm screws (E) into position.
Fixings Parts
B x 4 PCS 2
E x 6 PCS 5
6
If using option A only. If rebates are not being used go to step 4.
Now join all 3 inside panels (7 & 8) to the rear of the surround via 6 dowels, once glued into position screw 9x 50mm screws
(F) to secure the surround together. Ensure the labels on the rebates are facing outwards.
Fixings Parts
A x 6 PCS 7
F x 9 PCS 7
8
STEP 3
E
EE
EEE
BB
B B
②
⑥
⑤
F
F
F
F
F
F
F
F
F
A
A
A
A
A
A
⑦
⑦
⑧

4.0 ASSEMBLY - CONTINUED GB IE
5© 2017 Focal Point Fires plc.
Insert 2 cam locks (C) into each leg and 1 into the centre of the front panel,ensuring that all the cross heads are facing out-
wards. Next prepare the top panel (1) by screwing all 5 cam bolts (D) into position. The dowel joints (A) need to be glued in
at both ends of the top panel. Connect the top panel to the surround, making sure all 9 inserts are in their correct position.
Once home, all 5 cam locks (C) can be tightened into position.
Fixings Parts
A x 4 PCS 1
C x 5 PCS
D x 5 PCS
STEP 4
A
AAA
A
A
C
CC
C
C
C
D
D
DD
D
D
D
①
5.0 INSTALLATION
Fixings
G x 2 PCS
I x 4 PCS
H x 2PCS
J x 2 PCS
With a pencil mark out the desired height where you would like the mirror brackets (H) to be situated on the rear of the legs. To avoid
splitting the leg, pre drill the bracket holes with a 2mm drill bit. Now attach the brackets to the legs using the 6x19mm screws (I). Once
the brackets are in position, centre and level the hearth into its final fitting position. Position the surround on the hearth to correspond
with the header/fireplace lintel, mark with a pencil on the wall where you wish to drill. Remove the surround and prepare the wall from
the marked positions. If using the fixings supplied, drill a hole in the wall using a 6mm drill bit. If not, use a suitable drill bit for the wall
plugs you are using. Insert the wall plugs into position. Offering the surround back up into position against the wall, you are now able to
secure the surround to the wall using the 2x38mm screws (G).
II
H
H
I
I
G
G
J
J

6© 2017 Focal Point Fires plc.
6.0 CLEANING/ FINISHING GB IE
Before carrying out any of the following operations, ensure that the appliance is turned OFF and completely cold. Regularly
clean around the appliance to ensure that dust, fluff, pet hair etc, are kept to a minimum. There are no other specific require-
ments for care, other than regular cleaning of the general surround.
A wipe with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish. Test on a hidden
part before cleaning. Clean only in the direction of the grain. Regularly check that the surround is securely fixed in position.
7.0 GUARANTEE - TERMS AND CONDITIONS
F861475
As our policy is one of continuous improvement and development, we hope therefore you understand we must retain the right to amend details and/or specifications without prior notice.
The 3 year guarantee commences from the date of purchase, provided that the terms and conditions are adhered to:
Registration is not required.
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your
proof of purchase.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then
please submit the following information for the attention of the 3G Service Department to the address below. Alternatively, you
can email or fax. Please note that this does not affect your statutory rights.
Focal Point Fires plc, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Alternatively email: [email protected].uk or fax. [phone].
Details required:
1. Name, full address including post code and contact telephone number.
2. Receipt of purchase or credit card statement.