Quadra-Fire LOGS-QFI35FB User manual

1
Quadra-Fire • LOGS-QFI35FB Log Instructions • 2223-935 Rev. D • 5/18
Log Set Assembly: LOGS-QFI35FB
Models: QFI35FB, QFI35FB-C, QFI35FB-IFT
LOG PLACEMENT INSTRUCTIONS
CAUTION: Logs are fragile, handle with care.
Glass Rock (2201-853): Fill each light tray evenly with the glass rock.
WARNING! Risk of Explosion! DO NOT place glass rock on the burner surface. DO NOT place glass rock directly over
burner ports. Improperly placed glass rock interferes with proper burner operation.
Figure 3. Install Glass Rock
Figure 4. Place Log #1 Figure 5. Place Log #2
Figure 1. Logs Installed
GRATE TINES
PILOT BRACKET
LOG PINS
LIGHT TRAYS
LOG SUPPORTS
GRATE BAR
6
5
12
4
7
3
Figure 2. Reference Points for Log Placement
Log #1 (SRV2223-703): Position Log #1 as shown in Figure 4. See Figure 2 for additional points of reference. Center the
log over the pilot bracket. The log should rest on the burner ledge as shown in Figure 4.
Log #2 (SRV2223-701): Position Log #2 as shown in Figure 5. See Figure 2 for additional points of reference. Place the
left end of the log on the rear log support. Slide the log back until it rest against the back of the log support. The left end of
the log should touch Log #1. Swing the right end of the log counterclockwise until it contacts the right refractory wall.
GLASS ROCK
FLAT SPOT
FOR LOG #7
FLAT SPOT
FOR LOG #6
LOG #1 CONTACTS BURNER
LEDGE AT TWO POINTS
CENTER LOG CUT OUT
OVER PILOT BRACKET
LOG #2 TOUCHES
LOG #1 HERE
LOG #2 CONTACTS
RIGHT FIREBOX WALL
1
2
1
BURNER LEDGE
BURNER
LEDGE
SRV2223-703
SRV2223-701
SRV2223-702
SRV2223-704
SRV2223-706SRV2223-705
SRV2221-707

Quadra-Fire • LOGS-QFI35FB Log Instructions • 2223-935 Rev. D • 5/182
Log #4 (SRV2223-706): Position Log #4 as shown in Figure 9. See Figure 2 and Figure 8 for additional references. Mate
the slot located at the left end of log #4, shown in Figure 8, with the right log pin. Rotate the right end of the log clockwise,
until the log contacts the grate bar.
Figure 8. Log #4 - Bottom View Figure 9. Place Log #4 (Glass Rock not Shown)
MATE LOG PIN
WITH LOG SLOT
Figure 11. Place Log #6 (Glass Rock not Shown)
4
Figure 6. Log #3 - Bottom View
Log #3 (SRV2223-702): Position Log #3 as shown in Figure 7. See Figure 2 and Figure 6 for additional references. Mate
the grate tine groove with the base of the left grate tine. Slide the log forward until it stops against the vertical portion of the
left grate tine. Mate the burner top groove with the left edge of the burner top as shown in Figure 7.
GRATE TINE GROOVE
FRONT BACK
BURNER TOP GROOVE
Figure 7. Place Log #3
33
LOG PIN SLOT
LOG CONTACTS
GRATE BAR
5
3
1
2
Figure 10. Place Log #5 (Glass Rock not Shown)
RIGHTLEFT
REST ENDS OF LOGS
ON THE FLAT SPOTS
6
Log #5 (SRV2223-704): Position Log #5 as shown in Figure 10. See Figure 2 and Figure 7 for additional references. Rest
the left end of the log on the at spot of log #3. Locate the groove located on the right end of the log. Mate the groove with
the grate bar. Use the left log pin to positively locate the right end of the log.
Log #6 (SRV2223-705): Position Log #6 as shown in Figure 11. See Figures 2, 5 and 10 for additional reference points.
Place the front and back ends of the log on the at spots as shown in Figure 11.
FLAT SPOT
FOR LOG #5
FLAT SPOT
FOR LOG #7
FLAT SPOT
FOR LOG #6
USE LOG PIN TO
LOCATE LOG
LINE SHOWS BACK
EDGE OF GRATE BAR
LOG #3 TOUCHES
GRATE TINE
MATE GROOVE WITH
CORNER OF BURNER TOP
4
REST LOG ON
FLAT SPOT

3
Quadra-Fire • LOGS-QFI35FB Log Instructions • 2223-935 Rev. D • 5/18
Figure 12. Place Log #7
Log #7 (SRV2221-707): Position Log #7 as shown in Figure 12. See Figure 2 and 10 for additional reference points. Place
the front and back ends of the log on the at spots as shown in Figure 12.
7
PLACE END OF LOG
ON FLAT SPOT
REST END OF LOG
ON THE LEFT SIDE OF
KNOT
KNOT