pleasant hearth MERLOT 24-44-34M User manual

1
MODEL #24-44-34M / 24-42-34M
ATTACH YOUR RECEIPT HERE
Serial Number ________________________________ Purchase Date _________________________________
20-10-225 Rev. 06/15/17
Questions, problems, missing parts?
Before returning to your retailer, call our customer service department at 1-877-447-4768,
8:30 a.m. – 8:00 p.m. CST, Monday – Friday or email us at [email protected]
Español p. 10
Français p. 19
MERLOT MANTEL FOR 24” FIREBOX

2
PACKAGE CONTENTS
HARDWARE CONTENTS
Bolt
Qty. 62 Long
Connector
Qty. 4
Short
Connector
Qty. 25
AA BB CC DD EE FF GG
Knob
Qty. 2
H
E
D
GF K
C
B
A
JM
P
NQ
HH JJ
Hinge
Screw
Qty. 24
Shelf Pin
Qty. 8
Back
Panel Screw
Qty. 36
Cabinet
Door
Hinge
Qty. 4
Dowel
Qty. 34
L
KK
Dowel
Qty. 4

3
PACKAGE CONTENTS
Some parts and specications may change without notice.
A
B
C
D
E
F
G
H
J
K
L
M
N
P
Q
AA
BB
CC
DD
EE
FF
GG
HH
JJ
KK
1
1
1
1
2
1
1
1
1
1
1
2
2
1
2
62
25
4
30
2
36
4
8
24
4
Top Panel
Base
Media Shelf
Upper Back Panel
Side Panel
Left Inner Panel
Right Inner Panel
Left Door
Right Door
Left Trim Panel
Right Trim Panel
Lower Back Panel
Upper Side Panel
Top Trim Panel
Adjustable Shelf
Bolt
Short Connector
Long Connector
Dowel
Knob
Back Panel Screw
Cabinet Door Hinge
Shelf Pin
Hinge Screw
Dowel
20-12-718
20-12-719
20-12-720
20-12-721
20-12-722
20-12-723
20-12-724
20-12-725
20-12-726
20-12-829
20-12-830
20-12-729
20-12-730
20-12-831
20-12-732
20-09-530
PART QTY.DESCRIPTION
PART NO.
MERLOT FINISH
24-44-34M/24-42-34M

4
Carefully remove all pieces from carton and
make sure that you have all parts listed (refer
to parts list on page 2-3).
If you are missing parts, please call GHP
customer service at 1-877-447-4768.
1. Lay the right inner side panel (G), the left
inner side panel (F), and both side panels (E)
on a clean, at surface. The side with the most
predrilled holes should be facing up. Attach
two short connectors (BB) into predrilled holes
on each end of the panels with bolts (AA) as
shown.
2. Turn the right inner side panel (G) and the
left inner side panel (F) over and attach two
long connectors (CC) into predrilled holes on
each edge of the panels with bolts (AA) as
shown.
3. Insert 3 dowels (DD) into predrilled holes
in the left trim panel (K) and the right trim
panel (L). Slip the left trim panel (K) into the
predrilled holes in the edge of the left inner side
panel (F) until snug. Secure with bolts (AA) as
shown. Repeat using the right trim panel (L)
and the right inner side panel (G).
ASSEMBLY INSTRUCTIONS
1
3
G
G
F
E
AA
CC
2
G
AA
AA
F
K
L
F
DD
BB

5
4. Lay the top trim panel (P) curved side down.
Insert short connector (BB) into predrilled holes
and secure with bolt (AA).
5. Insert 2 dowels (KK) into predrilled holes in
each end of the top trim panel (P). Slip the left
end of the top trim panel (P) into the predrilled
holes in the edge of the left panel assembly
until snug. Repeat using the right panel
assembly.
6. Set base (B) on a clean, at surface. Insert
8 dowels (DD) into predrilled holes in the base
(B) as shown. Slip previously assembled inner
panel over dowels (DD) until snug and secure
with bolts (AA). Slip each of the side panels (E)
over dowels (DD) in left and right edges of the
base (B), at side facing out, and secure with
bolts (AA).
ASSEMBLY INSTRUCTIONS
5
AA
BB
4
P
KK
F
G
6
P
E
E
B
AA
DD

6
7. Insert 8 dowels (DD) into predrilled holes in
top edge of the base assembly. Set the media
shelf (C) over dowels (DD) and connectors until
snug. Secure with bolts (AA) from underneath
the media shelf (C).
8. Set both of the upper side panels (N) on a
clean, at surface. Insert 4 short connectors
(BB) into predrilled holes in each of the upper
side panels (N). Secure with bolts (AA).
9. Insert 4 dowels (DD) into predrilled holes in
top of base assembly. Slip one of the upper
side panels (N) over dowels (DD) on left end of
the base assembly until snug and secure with
bolts (AA). Repeat using the remaining upper
side panel (N) on the right side of the base
assembly.
ASSEMBLY INSTRUCTIONS
9AA
8
7
N
DD
AA
N
BB
C
DD
AA

7
10. Insert 4 dowels (DD) into predrilled holes in
top edge of upper side panels (N). Set top (A)
over dowels (DD) and connectors until snug.
Secure top (A) from underneath with bolts (AA).
11. Attach the upper back panel (D) with back
panel screws (FF). Attach both lower back
panels (M) on each side with back panel
screws (FF).
12. Lay the left door (H) and right door (J) on
a clean, at surface. Attach the cabinet door
hinges (GG) to each door using hinge screws
(JJ) as shown.
ASSEMBLY INSTRUCTIONS
12
A
GG
11
10
AA
H
DD
D
J
FF
M
JJ
N

8
13. Insert 4 shelf pins (HH) into predrilled
holes in side walls of each cabinet at preferred
height. Attach the left door (H) to the left cabi-
net using hinge screws (JJ) as shown. Repeat
using the right door (J). Level the cabinet
doors using a Phillips screwdriver as shown
in inset diagrams. Attach knobs (EE) to each
door using screw included with knob (EE).
14. Set adjustable shelves (Q) in desired
positions in each cabinet.
15. Set completed mantel in desired position
against wall. Place the insert directly in front
of the mantel opening. Carefully lift the insert
through the center opening in the front of the
replace. The bottom of the insert has two
foam rubber strips to prevent scratching of the
hearth base. Slide the insert back through the
opening until the metal trim makes contact with
the front of the mantel.
ASSEMBLY INSTRUCTIONS
15
EE
14
13
JJ
Q
HH
Q
J
H

9
GHP Group, Inc.
6440 W. Howard St. • Niles, IL • 60714-3302
271 Massey Road • Guelph, ON • N1K 1B2
ONE YEAR LIMITED WARRANTY
If within one year from the date of original purchase, this item fails due to a defect in material or
workmanship, we will replace or repair at our option, free of charge. To order parts or obtain warranty
service, call 1-877-447-4768, 8:30 a.m. – 4:30 p.m. CST, Monday – Friday. This warranty does not
cover defects resulting from improper or abnormal use, misuse, accident, or alteration. Failure to follow
all instructions in the owner’s manual will also void this warranty. GHP Group, Inc. will not be liable for
incidental or consequential damages. Some states do not allow the exclsion or limitation of incidental or
consequential damages, so the above limitation or exclusion of incidental or consequential damages may
not apply to you. This warranty gives you specic legal rights and you may also have other rights which
vary from state to state.
Notice to the Customer
Our quality furniture is built keeping tradition in mind. Variations in actual wood color and nishes which may result
from natural characteristics of the wood, such as grain patterns, mineral streaks and the like, are not considered
defects. As wood continues to move and age you may notice these slight differences in color, even on different
parts of any individual unit. Sound knots and slight surface cracks are true personality of a quality piece of wood
furniture.
There are several practices we reccomend so that you may maintain your new furniture in top condition. First of all,
to maintain the nish, you should clean with a soft, slightly damp cloth and buff with a dry cloth. Secondly, wood
furniture should never be dragged across a oor. The added stress from dragging the unit may cause the dragged
edge to splinter or it may cause some joints to loosen.
Please contact us for any questions or concerns you may have regarding your new piece of furniture.
ONE YEAR LIMITED WARRANTY
Printed in China
6440 W. Howard St., Niles, IL 60714-3302
271 Massey Road, Guelph, ON N1K 1B2
877-447-4768

10
MODELO #24-44-34M / 24-42-34M
ADJUNTE SU RECIBO AQUÍ
Número de serie ________________________________ Fecha de compra _________________________________
20-10-225 Rev. 06/15/17
¿Preguntas, problemas, piezas faltantes?
Antes de volver a la tienda, llame a nuestro departamento de servicio al cliente al 1-877-447-4768,
de lunes a viernes de 8:30 a.m. a 4:30 p.m., hora central estándar o envíenos un correo electrónico a
[email protected].
REPISA DE LA CHIMENEA MERLOT
PARA CAJA DE COMBUSTIÓN 24”