Lennox Elite series User manual

DOOR TRIM KITS
MODEL EPIC™
INSTALLATION INSTRUCTIONS FOR INSTALLING DOOR TRIM
KITS FOR USE WITH EPIC DIRECT-VENT GAS STOVES
775,291M
Rev. A, 10/2008
HEARTH PRODUCTS
KITS AND ACCESSORIES
DRAFT
10/27/2008
KIT CONTENTS
Please ensure that all these parts are included
2 ea. Trim Pieces
6 ea. Nuts
6 ea. #6 Washers
1 ea. Instruction Sheet
TOOLS NEEDED:
5/16” nut driver or socket wrench
CAUTION: Always ensure that plated surfaces are clean and free of
fingerprints before lighting stove. Fingerprints will leave permanent
blemishes if left on plated surface when lit. When installation is
complete, the trim should be gently cleaned with a soft cloth and
either alcohol or a household glass cleaner. Do not overtighten nuts,
overtightening can create visible dimples on the plated surface.
INSTALLATION INSTRUCTIONS
Step 1. Remove the trim pieces and hardware from its packaging and
ensure that all pieces are present before beginning installation.
Take care not to scratch finished surfaces.
Step 2. Facing the stove pull open the left side door.
Step 3. Unlatch the front door and swing it open (See Figure 1).
GENERAL INFORMATION
If you encounter any problems, need clarification of these instructions
or are not qualified to properly install this kit, contact you local distribu-
tor or dealer.
Read this instruction sheet in its entirety before beginning the installa-
tion.
All of these parts may scratch and bend, great care should be used
in handling them.
ALL WARNINGS AND PRECAUTIONS IN THE INSTALLATION AND
OPERATION MANUAL PROVIDED WITH THE APPLIANCE APPLY TO
THESE INSTRUCTIONS.
TURN OFF THE STOVE AND ALLOW IT TO COMPLETELY COOL BEFORE
PROCEEDING.
1
Cat. No. Model Description
75348 EPIC-TRIM-B Black Trim Kit
75349 EPIC-TRIM-G Gold Trim Kit
75350 EPIC-TRIM-BN Brushed Nickel Trim Kit
75351 EPIC-TRIM-BKN Black Nickel Trim Kit
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
Figure 1 - Front Door Latches
Thefrontdoorlatchesarelocatedbehindthe
left side door panel (indicated by arrows)
fire-parts.com

2
Printed in U.S.A. © 2008 Lennox Hearth Products
P/N 775,291M REV. A 10/2008
NOTE: DIAGRAMS AND ILLUSTRATIONS ARE NOT TO SCALE.
Lennox Hearth Products reserves the right to make changes at any time, without notice, in
design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
1110 West Taft Avenue • Orange, CA 92865
Figure 3
Step 4. Put trim in place by inserting trim studs into the corresponding
holes in the door (see Figure 2). The top piece of trim will only fit
in one direction, but the bottom piece can be installed incorrectly.
When placing the bottom piece of trim make sure there is a small
gap between the bottom of the trim piece and the bottom of the
door, if the trim extends below the bottom of the door the trim is
on upside down.
Step 5. Place one washer on each stud (see Figure 2). Using a 5/16”
nut driver, snug up the nuts on each piece of trim. Do not finish
tightening nuts.
Step 6. There should be approximately a 1/8” gap between the edge of
the trim and the top and bottom of edges of the door. Visually
inspect the alignment of the trim and adjust if necessary.
Step 7. Finish tightening nuts. CAUTION - DO NOT OVERTIGHTEN
NUTS.
Figure 2
COMPLETED
INSTALLATION
Step 8. Close the front door and secure latches (see Figure 1). Close left
side panel door. Use a household glass cleaner or alcohol and
a soft cloth to remove any fingerprints from all plated surfaces
prior to firing the stove. Read Caution on Page 1.
fire-parts.com