Focal Point ATHERSTONE SLATE ELECTRIC SUITE Assembly Instructions

Focal Point Fires Ltd.
RBK House, Irishtown, Athlone,
Co. Westmeath, N37 XP52, Ireland
Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e: [email protected]
ATHERSTONE SLATE ELECTRIC SUITE
ATHERSTONE BRICK ELECTRIC SUITE
MODELS SHOWN: ATHERSTONE SLATE ELECTRIC SUITE
Revision - A 07/21
2021
ATHERSTONE BRICK ELECTRIC SUITE

2021

ATHERSTONE BRICK ELECTRIC
SUITE DS-EHS01-20E
ATHERSTONE SLATE ELECTRIC
SUITE DS-EHS01-19E
2021
36.5kg
H 800 x W 1000 x D 240(mm)
24kg
H 800 x W 1000 x D 240(mm)
ATHERSTONE ELECTRIC SUITE

2021
Recess any part of the appliance into the wall, or run the supply cable under carpets
Site in a position where curtains or drapes could cover the appliance , or other soft materials could cover e.g. below a coat rack
Site behind an opening door where mechanical impact/damage could occur
Site where the supply cable would become a trip hazard
Sit, stand or forcefully pull on the appliance
Obstruct,cover of force items into the openings
It should be noted that the appliance creates warm convected air currents.These currents move heat from the room surroundings
to, and up the wall surfaces adjacent to the heater.
Installing the heater next to these types of wall coverings or operating the heater where impurities in the air ,(such as tobacco
smoke) exist, may slightly discolour wall finishing.
If the appliance is to be secure on a dry lined or timber framed construction then the integrity and ability of the wall to secure the
appliance must be confirmed.It is important in these circumstances that any vapour barrier and or strucural members of the house
frame are not damaged.
If you are unsure of the ability of the wall to secure the appliance and or which type of wall fixing to use, you should take professional
advice and obtain the correct fixings.Alternatively , find a more suitable wall location.
DO NOT
1 Heater unit
2 Fixing brackets
4 3x12mm screws
2 Wall plugs
2 4x30mm screws

2021
STEP1
brackets A 2pcs
screws B 3x12mm 4pcs
With a pencil mark out the desired height where you
would like the brackets(A) to be situated on the rear of
the legs, to avoid splitting the leg, pre drill the bracket
holes with a 2mm drill bit. Now attach the brackets to
the legs using the 3x12mm screws(B).
Please note: Before drilling into wall, always
check that there are no hidden wires, pipes, etc.
Make sure that the screws and wall plugs supplied
are suitable for supporting the unit to the
surface. Consult a qualified person if you are not
sure.

2021
NOTE:
1.Mantel
2.Logs
3.Remote control
4.Heat settings
5. Flame effect
6. Fire ON/OFF
7. Power Switch
DOWN
LIGHT
button 3 seconds to turn on
This product without downlights.If the product without downlights function, press
the downlights function is invalid.
STEP2
STEP3
Once the brackets are in position, centre and level
the suite into its final fitting position, mark with a
pencil on the wall where you wish to drill. Remove
the suite and prepare the wall from the marked
positions. If using the fixings supplied, drill a hole in
the wall using a 5.5mm drill bit. If not, use a suitable
drill bit for the wall plugs you are using.
Insert the wall plugs into position. Offering the suite back
up into position against the wall, you are now able to
secure the suite to the wall using the 4x30mm screws.
Wall
Floor

2021
Before using any operation with the remote control, Insert 2 x AAA batteries to the back of the remote control.
If the product without downlights function, press the “Downlights” button on the remote control is invalid.
The remote control will not respond until the digital display is illuminated as it is in sleep mode.Before operating , press any
button once to illuminate the digital display in order to activate the remote control.
Do not press the remote control buttons more than once within two seconds for correct operation.Please wait for the receiver
to respond to the transmitter
NOTE:
NOTE:
STEP 1: Plug in and turn the mains power supply on.
STEP 2: Turn the switch on the right hand side of the heater outlet to “I”position.
STEP 3: Press the button to turn on the appliance.
STEP 4: Press the button once to activate the low heat setting , press it again to activate the high setting,
press it a third time to switch the heat setting off.
STEP 5 : To change the flame brightness , press the button to cycle through the brightness options.Turn
off the LED flame effect by pressing the button repeatedly until the flame effect cycles off.
STEP 6: Activate the standby mode by pressling the button again.
STEP 7:Switch the fire off by turning the switch on the right hand side of the heater to the “0”position.
STEP 1: Switch on the appliance using the switch.
STEP 2: Press the power button on the remote control; the LCD display will illuminate.
STEP 3: Press“FLAME”button on the remote control to select the desired flame brightness; there are 3 different
brightness levels available.
STEP 4: Select the desired heat output by pressing the relevant heat setting button:
To activate the low heat setting, press “HEAT l” ; press it again to turn it off.
To activate the low heat setting, press “HEAT ll” ; press it again to turn it off.
The day and time can only be set using the remote control.
STEP 1:Press the “ DATE TIME” button on the remote control , the day of the week will flash, Use the up and down
Setting the Current Day and Time
Remote Control Operation
Manual Operation
DOWN
LIGHT
LED Display
Up Selection
Down Selection
Open Window/Door detection
Heat II
Heat I
“-” Selection“+” Selection
Downlights
Flame Effect
Timer ON/OFF
Fire ON/OFF
Timer Set
Date Time Setting
Clear button
buttons to set the day of the week.Once the current day is set , press the “DATE TIME” button to confirm the current day.
STEP 2: The hour setting will then flash once the day has been selected .Use“+”or “-” to adjust the time until the current
hour is selected.Press the “DATE TIME” button to confirm the current hour.
STEP 3: Then the minute setting will flash once the hour has been set.Use“+”or “-” to adjust the time until the current minute is
set correctly.Press the “DATE TIME” button to confirm the current minute.

2021
Setting the Heat Timer
Selecting the Day
Set TIMER ON Time
Set TIMER OFF Time
Safety Cutout System
ALWAYS DISCONNECT THE APPLIANCE FROM THE MAINS SUPPLY OUTLET
SOCKET BEFORE UNDERTAKING ANY CLEANING OR MAINTENANCE!
Press the “TIMER SET” button on the remote control, the time cycle number will flash. Use the “+” and “-” buttons to cycle
through the different timer cycles from 1 to 10 and press the “TIMER SET ” button to confirm. A small black triangle will flash
below one day of the week,indicating that the day of the week need to be determined.
Press the “CLEAR” button can cancel the set time conveniently.
STEP 1: Press the up or down buttons on the remote control to choose the set day between“SUN” to “SAT”, the default day is
“SUN”. Press the “+” button to confirm the set day. Press the “ TIMER SET ” button to confirm.
STEP 2: Repeat STEP 1 to add other days to the chosen timer cycle, or press the “-” button to delete the set day. Press the
“TIMER SET ” button to confirm.
The “ON” symbol will illuminate on the LCD display to indicate that the Timer ON will need to be set.
STEP 1: Press the “+” or “-” button to set the hour setting for Timer ON and press the “TIMER SET” button to confirm.
STEP 2 : Press the “+” or “-” button to set the minute setting for Timer ON and press the “TIMER SET” button to confirm.
The “ON” symbol with turn off and the “OFF” symbol will illuminate.
The “OFF” symbol will illuminate on the digital display to indicate that the timer OFF will need to be set.
STEP 1: Press the “+” or “-” button to set the hour setting for Timer OFF and press the “TIMER SET” button to confirm.
STEP 2: Press the “+” or “-” button to set the minute setting for Timer OFF and press the “TIMER SET” button to confirm.
CAUTION: This product has a self-resetting overheat protection device. In the event that the heater stops working as a
result of overheating, the fan kept working all the time, take the following immediate steps , switch the electricity off at the
socket and remove the plug. Remove any objects that are covering the product.
CAUTION: Do not touch the heater as it will be hot. Set the heater switches to OFF and leave the heater to cool down fully.
Once completely cool, reconnect the heater and switch it on. Do not open this product , There are no user-serviceable parts.
Open Window/Door detection
When this function is enabled , if the ambient temperature is lowered due to the opening of th doors or windows, indicator
light on “HEAT” button on the appliance will blink to remind the user to close the window/door. If there is no resphonse, the
system will automatically stop heating.The heater can be turned back on by pessing "HEAT I " or "HEAT II".
NOTE: Press the window button once to active the window monitor, Press it again to switch the window monitor off.
1. Remove the plug from the wall socket.
2. Remove the 2 screws holding the fuel bed into position.
3. Remove the 4 screws that hold the flame effect into position.
4. Remove the LED strip and unplug the small connector.
5. Replace with a new LED strip and reassemble the appliance.
2 screws
4 screws

2021
The flame effect does not work
1000
500
210
190
240
1000
800
50

2021
F861592
This product complies with conformity
requirements of the applicable
European Regulations or Directives.
This product complies with conformity
requirements of the applicable UK
Regulations.