Jetmaster HEAT & GLO MEZZO-AU User manual

JETMASTER (VIC) Pty Ltd
ACN 005 872 159 ABN13 659 821 337
444 Swan Street Richmond 3121
Phone: [phone] Fax: [phone]
Email: [email protected] Web: www.jetmastervic.com.au
V-JOINT TO PLASTERBOARD & WHITE INSULATION BOARD, BUTT JOIN EACH AND BACK FILL WITH BASE COAT.
OVERLAY JOIN WITH FIBREGLASS TAPE AS FIRST JOINT, THEN TROWEL BASE AND TOP COAT OVER.
NOTE - Unit must be installed (and gas connected) prior to plaster sheeting.
• Position unit into framed opening with minimum clearances as per specifications on following pages. Frame opening
height is from the bottom of unit. This unit is designed to be raised from the floor.
• Run flues in accordance with the options in the installation manual.
• Butt join plasterboard and white insulation board at top of heater. USING ONLY FIBREGLASS TAPE finish insulation
board to plasterboard as per normal plasterboard procedures. Ensure that top coat finish extends down to top of
heater, as indicated in diagram below. Insulation board will remain exposed as part of the finished plaster face.
• Unit should always be operated with External Fan in the ON position. Failure to run the fan may result in hairline cracks
appearing in the plaster above the unit.
Owner’s Manual
Care and Operation
H t & Gl MEZZO 1000 AU MEZZO 1300 AU MEZZO 1300ST AU MEZZO 1600 AU O ’ M l 2304 971 R C 3/15
ADDENDUM
PLEASE NOTE
ON THE FOLLOWING MODELS:
MEZZO-1000-AU / MEZZO-1300-AU / MEZZO-1600-AU
1. FANS MUST BE RUN AT ALL TIMES!
2. RUNNING HEAT ZONE FANS IS
OPTIONAL
Owner’s Manual
Care and Operation
H t & Gl MEZZO 1000 AU MEZZO 1300 AU MEZZO 1300ST AU MEZZO 1600 AU O ’ M l 2304 971 R C 3/15
ADDENDUM
PLEASE NOTE
ON THE FOLLOWING MODELS:
MEZZO-1000-AU / MEZZO-1300-AU / MEZZO-1600-AU
1. FANS MUST BE RUN AT ALL TIMES!
2. RUNNING HEAT ZONE FANS IS
OPTIONAL
JM-155 (10/15)

JM-155 (10/15)
 
2304-970 Rev. D • 3/15
NOTE - I mportant in f ormation regarding M e zz o installation
Please be advised of the following
M UST D O items concerning M e zz o appliance setup for installers
-M e zz o fireplaces must AL W AYS be run with the fan / s operating
- Retaining brackets for glass refractory panels should be installed so as to not pinch the panels. If the
brackets are slightly angled or are tight against the refractory glass, it can cause the glass to crack under
the pressure of expansion of heating up. PLEASE NOTE
: This will not be covered under warranty by
HH T or J etmaster in the event of breakage ( see page 50 of the manual )
- Glass media should not cover or impede the area in front of the pilot or to be placed in such a way that
could cause the glass to fall into the pilot assembly area. Delayed ignition potentially causing explosive
ignition can occur as a result (see pages 52 and 53)
-D
o not put any flat media pieces larger than
13 mm in diameter near the pilot. D elayed ignition could
occur. Use only round
13 mm pieces near the pilot as per figure 11 . 5 ( page 51) on the attached manual.
I M PORTANT POINTS TO NOTE
- Use the nailing tabs provided to properly position, level and secure the appliance to the framing.
- They are designed as a means to ensure the fireplace is mounted flush with the framing materials
- They ensure the plaster join to the non - combustible board is supported ade q uately
- D o not use cornice cement compound as it appears to dry too hard and can be subject to cracking
- D o not use paper tape for joining plaster to non - com board as it can be affected by the heat and lift away
from the plaster. Fibreglass tape is recommended.
- White board must be secured to the framing board.
It is imperative that these points are followed to ensure the continuity of the product finish.
JM-155 (10/15)
 
2304-970 Rev. D • 3/15
NOTE - I mportant in f ormation regarding M e zz o installation
Please be advised of the following
M UST D O items concerning M e zz o appliance setup for installers
-M e zz o fireplaces must AL W AYS be run with the fan / s operating
- Retaining brackets for glass refractory panels should be installed so as to not pinch the panels. If the
brackets are slightly angled or are tight against the refractory glass, it can cause the glass to crack under
the pressure of expansion of heating up. PLEASE NOTE
: This will not be covered under warranty by
HH T or J etmaster in the event of breakage ( see page 50 of the manual )
- Glass media should not cover or impede the area in front of the pilot or to be placed in such a way that
could cause the glass to fall into the pilot assembly area. Delayed ignition potentially causing explosive
ignition can occur as a result (see pages 52 and 53)
-D
o not put any flat media pieces larger than
13 mm in diameter near the pilot. D elayed ignition could
occur. Use only round
13 mm pieces near the pilot as per figure 11 . 5 ( page 51) on the attached manual.
I M PORTANT POINTS TO NOTE
- Use the nailing tabs provided to properly position, level and secure the appliance to the framing.
- They are designed as a means to ensure the fireplace is mounted flush with the framing materials
- They ensure the plaster join to the non - combustible board is supported ade q uately
- D o not use cornice cement compound as it appears to dry too hard and can be subject to cracking
- D o not use paper tape for joining plaster to non - com board as it can be affected by the heat and lift away
from the plaster. Fibreglass tape is recommended.
- White board must be secured to the framing board.
It is imperative that these points are followed to ensure the continuity of the product finish.

JM-155 (10/15)
 
2304-970 Rev. D • 3/15
NOTE - I mportant in f ormation regarding M e zz o installation
Please be advised of the following
M UST D O items concerning M e zz o appliance setup for installers
-M e zz o fireplaces must AL W AYS be run with the fan / s operating
- Retaining brackets for glass refractory panels should be installed so as to not pinch the panels. If the
brackets are slightly angled or are tight against the refractory glass, it can cause the glass to crack under
the pressure of expansion of heating up. PLEASE NOTE
: This will not be covered under warranty by
HH T or J etmaster in the event of breakage ( see page 50 of the manual )
- Glass media should not cover or impede the area in front of the pilot or to be placed in such a way that
could cause the glass to fall into the pilot assembly area. Delayed ignition potentially causing explosive
ignition can occur as a result (see pages 52 and 53)
-D
o not put any flat media pieces larger than
13 mm in diameter near the pilot. D elayed ignition could
occur. Use only round
13 mm pieces near the pilot as per figure 11 . 5 ( page 51) on the attached manual.
I M PORTANT POINTS TO NOTE
- Use the nailing tabs provided to properly position, level and secure the appliance to the framing.
- They are designed as a means to ensure the fireplace is mounted flush with the framing materials
- They ensure the plaster join to the non - combustible board is supported ade q uately
- D o not use cornice cement compound as it appears to dry too hard and can be subject to cracking
- D o not use paper tape for joining plaster to non - com board as it can be affected by the heat and lift away
from the plaster. Fibreglass tape is recommended.
- White board must be secured to the framing board.
It is imperative that these points are followed to ensure the continuity of the product finish.
JM-155 (10/15)
 
2304-970 Rev. D • 3/15
NOTE - I mportant in f ormation regarding M e zz o installation
Please be advised of the following
M UST D O items concerning M e zz o appliance setup for installers
-M e zz o fireplaces must AL W AYS be run with the fan / s operating
- Retaining brackets for glass refractory panels should be installed so as to not pinch the panels. If the
brackets are slightly angled or are tight against the refractory glass, it can cause the glass to crack under
the pressure of expansion of heating up. PLEASE NOTE
: This will not be covered under warranty by
HH T or J etmaster in the event of breakage ( see page 50 of the manual )
- Glass media should not cover or impede the area in front of the pilot or to be placed in such a way that
could cause the glass to fall into the pilot assembly area. Delayed ignition potentially causing explosive
ignition can occur as a result (see pages 52 and 53)
-D
o not put any flat media pieces larger than
13 mm in diameter near the pilot. D elayed ignition could
occur. Use only round
13 mm pieces near the pilot as per figure 11 . 5 ( page 51) on the attached manual.
I M PORTANT POINTS TO NOTE
- Use the nailing tabs provided to properly position, level and secure the appliance to the framing.
- They are designed as a means to ensure the fireplace is mounted flush with the framing materials
- They ensure the plaster join to the non - combustible board is supported ade q uately
- D o not use cornice cement compound as it appears to dry too hard and can be subject to cracking
- D o not use paper tape for joining plaster to non - com board as it can be affected by the heat and lift away
from the plaster. Fibreglass tape is recommended.
- White board must be secured to the framing board.
It is imperative that these points are followed to ensure the continuity of the product finish.

JETMASTER (VIC) Pty Ltd
ACN 005 872 159 ABN13 659 821 337
444 Swan Street Richmond 3121
Phone: [phone] Fax: [phone]
Email: [email protected] Web: www.jetmastervic.com.au
V-JOINT TO PLASTERBOARD & WHITE INSULATION BOARD, BUTT JOIN EACH AND BACK FILL WITH BASE COAT.
OVERLAY JOIN WITH FIBREGLASS TAPE AS FIRST JOINT, THEN TROWEL BASE AND TOP COAT OVER.
NOTE - Unit must be installed (and gas connected) prior to plaster sheeting.
• Position unit into framed opening with minimum clearances as per specifications on following pages. Frame opening
height is from the bottom of unit. This unit is designed to be raised from the floor.
• Run flues in accordance with the options in the installation manual.
• Butt join plasterboard and white insulation board at top of heater. USING ONLY FIBREGLASS TAPE finish insulation
board to plasterboard as per normal plasterboard procedures. Ensure that top coat finish extends down to top of
heater, as indicated in diagram below. Insulation board will remain exposed as part of the finished plaster face.
• Unit should always be operated with External Fan in the ON position. Failure to run the fan may result in hairline cracks
appearing in the plaster above the unit.
Owner’s Manual
Care and Operation
H t & Gl MEZZO 1000 AU MEZZO 1300 AU MEZZO 1300ST AU MEZZO 1600 AU O ’ M l 2304 971 R C 3/15
ADDENDUM
PLEASE NOTE
ON THE FOLLOWING MODELS:
MEZZO-1000-AU / MEZZO-1300-AU / MEZZO-1600-AU
1. FANS MUST BE RUN AT ALL TIMES!
2. RUNNING HEAT ZONE FANS IS
OPTIONAL
Owner’s Manual
Care and Operation
H t & Gl MEZZO 1000 AU MEZZO 1300 AU MEZZO 1300ST AU MEZZO 1600 AU O ’ M l 2304 971 R C 3/15
ADDENDUM
PLEASE NOTE
ON THE FOLLOWING MODELS:
MEZZO-1000-AU / MEZZO-1300-AU / MEZZO-1600-AU
1. FANS MUST BE RUN AT ALL TIMES!
2. RUNNING HEAT ZONE FANS IS
OPTIONAL
JM-155 (10/15)