Focal Point F820906 Programming manual

ASSEMBLY & INSTALLATION INSTRUCTIONS
Please note : Except where otherwise stated, all rights, including copy-
right in the text, images and layout of this booklet is owned by Focal
Point Fires Ltd.You are not permitted to copy or adapt any of the con-
tent without the prior written permission of Focal Point Fires Ltd.
1
All instructions must be handed to the user for
safekeeping.
Revision B- 05/21
© 2021 Focal Point Fires Ltd.
MODELS COVERED BY THESE INSTRUCTIONS
F820906 MAINE GREY-OAK FIRE SURROUND
.FoFocal Point Fires Ltd
Christchurch, Dorset BH23 2BT
Tel: 01202 49933499330
Fax: [phone]
www.focalpointfires.co.uk
e : [email protected]
Focal Point Fires Ltd
RBK House, Irishtown, Athlone,
Co. Westmeath, N37 XP52,
Ireland Tel: [phone]
Fax: [phone]
www.focalpointfires.co.uk
e: [email protected]

ASSEMBL Y INSTRUCTIONS
2
GB IE
1.0 IMPORTANT NOTES
© 2021 Focal Point Fires Ltd.
Section
1.0
2.0
3.0
4.0
5.0
6.0
7.0
Contents
Important notes
Tools required
Hardware & parts list
Assembly
Installation
Cleaning/ finishing
Guarantee - terms and conditions
Page No.
2
2
2
3
4.0 Assembly4
4
5.0 Installation 5
5
5
2.0 TOOLS REQUIRED
3.0 HARDWARE & PARTS LIST
To ensure safe and stable installation:
1.The assembled Fire Surround must be fixed / secured to wall.
2.The wall must be sturdy and in good repair.
3. Some walls require alternative fixings (not included).
4.When drilling into the wall, check for hidden pipes and cables.
5.There are two options for construction of this surround.
A - with rebates - If you are installing this surround with a gas fire, or an electric fire where there is space in the wall to recess
the fire, this means the laminate / marble is up against the wall.
B - with out rebates - If using this surround with an electric fire and a flat wall you will need to remove the rebates, instead use
the spacer frame from the fire.
Cross head screwdriver PZ2 (3 inches in length or greater)
Drill, 6mm and a 2mm suitable drill bit
Pencil
Tape measure
16PCS

4.0 ASSEMBLY
3
GB IE
© 2021 Focal Point Fires Ltd.
Gently lay both legs you have prepared onto a suitable protected surface. Be extremely careful not to scratch the front edges
of the legs. DO NOT DRAG THE LEGS! Make sure that the legs are lifted everytime they are moved to avoid them from
being damaged.
Using a drop of glue (I) in each dowel hole, insert two dowels (A) in to the left side panel (6). Again, using a drop of glue (I) in
the dowel holes take the front panel (2) and push them on to the dowels (A). Use 2x wood screws (D) to screw the parts
together. Repeat the process for the right side panel (7) and front panel (2).
Fixings
A x 4 PCS
D x 4 PCS
STEP 1
Fixings
A x 6PCS
Dx 9PCS
Using a drop of glue (I) in each dowel hole, insert 2x dowels (A) in to the left side panel (6). Again, using a drop of
glue (I) in the dowel holes take the inside leg (5) and push them on to the dowels of the left side panel (6).
Use 3x wood screws (D) to screw the inside leg (5) to the left side panel (6). Repeat the process to secure the other
two inside legs (5) to the right side panel (7) and front panel (2).
STEP 2
Fixings

4.0 ASSEMBLY
4
GB IE
© 2021 Focal Point Fires Ltd.
Fixings
A x 2 PCS
B x 5 PCS
C x 5 PCS
STEP 3
If using option A only. If rebates are not being used go to section 5.
Use the glue (I) in the dowel holes before inserting 2x dowels (A) into the left and right hand panels (6and 7). Position the
cam bolts (C) in to left and right side panels (6and 7).
Take the left side and the right side legs (3and 4), put some glue (I) in to the dowel holes. Connect the side legs (3 and 4) to
the side panels (6 and 7), make all the inserts are in the correct position. Insert the cam locks (B),turn the cam locks (B)
clockwise to lock the parts together.
4.0 ASSEMBLY
Insert 5x cam locks (C) and glue (I) 2x wood dowels (A) into the legs, side panels and front panel (2,3,4,6 & 7).
Next prepare the top panel (1) by screwing all 5x cam bolts (C) into position. The dowel joints (A) need to be glued in at both
ends of the top panel. Connect the top panel to the surround, making sure all inserts are in the correct position. Once home,
all 5x cam locks (B) can be tightened into position.
STEP 4
⑥
⑦
⑤
⑤
⑤
②
②
③
④
⑥
⑤
⑤
⑤
⑦
Fixings
B x 6 PCS
C x 6 PCS
Ax 4PCS

5© 2021 Focal Point Fires Ltd.
Before carrying out any of the following operations, ensure that the appliance is OFF and completely cold. Regularly clean
around the appliance to ensure that dust, fluff, pet hair etc, are kept to a minimum.There are no other specific requirements for
care, other than regular cleaning of the general appliance.
A wipe with a dry cloth is normally sufficient. DO NOT use abrasive cleaners as they can damage the finish.Test on a hidden
part before cleaning. Clean only in the direction of the grain. Regularly check the surround is securely fixed in position.
7.0 GUARANTEE - TERMS AND CONDITIONS
The 3 year guarantee commences from the date of purchase, provided that the terms and conditions are adhered to:
Registration is not required.
1. For any claim to be made within the 3 years from date of purchase you will be required to provide and supply us with your
proof of purchase.
Making a claim is easy.
If you wish to make a claim under our 3 year guarantee and all the terms and conditions for your product have been met then
please submit the following information for the attention of the 3G Service Department to the address below.Alternatively, you
can email or fax. Please note that this does not affect your statutory rights.
Focal Point Fires Ltd, 3G Service Department, Reid Street, Christchurch, Dorset, BH23 2BT.
Alternatively email: [e-mail] or fax. [phone].
Details required:
1. Name, full address including post code and contact telephone number.
2. Receipt of purchase or credit card statement.
F820805
As our policy is one of continuous improvement and development, we hope therefore you understand we must retain the right to amend details and/or specifications without prior notice.
6.0 CLEANING/ FINISHING GB IE
5.0 INSTALLATION GB IE
Fixings
E x 2 PCS
F x 4 PCS
G x 2 PCS
H x 2 PCS
With a pencil mark out the desired height where you would like the mirror brackets (H) to be situated on the rear of the legs. To avoid
splitting the leg, pre drill the bracket holes with a 2mm drill bit. Now attach the brackets to the legs using the 3x12mm screws (F). Once
the brackets are in position, centre and level the hearth into its final fitting position. Position the surround on the hearth to correspond
with the header/ fireplace lintel, mark with a pencil on the wall where you wish to drill. Remove the surround and prepare the wall from
the marked positions. If using the fixings supplied, drill a hole in the wall using a 6mm drill bit. If not, use a suitable drill bit for the wall
plugs you are using. Insert the wall plugs (G) into position. Offering the surround back up into position against the wall, you are now
able to secure the surround to the wall using the 4x30mm screws (E).