Lennox Hearth Products Montebello LSM40-2 User manual

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 1
CERAMIC PANEL AND LOG
PLACEMENT GUIDE
CERAMIC PANEL & LOG PLACEMENT GUIDE FOR LSM40-2 & LSM45-2 MONTEBELLO SERIES GAS APPLIANCES
LSM40-2 AND LSM45-2
MONTEBELLO®SERIES
750,182M
REV. B
04/2006
GENERAL INFORMATION
This ceramic panel and log and placement guide has been prepared to
present detailed placement illustrations and provide instruction to assist
in the initial (new appliance) setup and after the annual cleaning and
inspection cycles. The information provided here is to be used in
conjunction with the Homeowner's Care and Operation Instructions
provided together with this document in the appliance literature packet.
Please read the Homeowner's Care and Operation Instructions completely
before completing the procedures detailed in this placement guide.
INITIAL INSTALLATION CONSIDERATIONS
If the ceramic panels and logs are being installed for the first time,
the following paragraphs apply:
DO NOT attempt to install the logs until the appliance installation
has been completed, the gas line connected and tested for leaks
and the initial burner operation has been checked out.
Step 1. Remove the boxed ceramic panels from the packaging.
Handle panels carefully to prevent breakage.
Step 2. Remove the appliance front door.
Step 3. Cut and remove the nylon securing the grate, the boxed
log set and bottom panel to the interior of the fireplace.
Step 4. Remove the logs from their packaging. Handle logs
carefully to prevent breakage.
Step 5. Remove the bottom panel from its packaging. Handle
panel carefully to prevent breakage.
CERAMIC PANEL, LOG AND GLOWING EMBER PLACEMENT
Step 1. Install the ceramic panels as shown in Figure 3 . Panels
should be placed in the order shown.
A. Remove the two L-brackets.
B. Slide the bottom edge of the bottom rear panel between the
grate assembly and the back wall.
C. Tilt and slide the bottom edge of the right side panel up against the
side wall as shown. Re-install the L-bracket to hold the panel in place.
D. Tilt and slide the right edge of the top rear panel and rest the
bottom edge on the bottom rear panel as shown.
E. Repeat Step C for the left panel.
Step 2. Place a mixture of volcanic stone and vermiculite around
the burner as shown in
Figure 4 .
Figure 1
Figure 2
Step 3. Separate the Glowing Ember (Rockwool) into pieces about
the size of a quarter ( see Figure 1) . Keep the pieces fluffed, not
matted. Distribute these pieces over the burner as shown in Figure
2 . Do not use more than necessary. When properly positioned, the
Glowing Embers will cover approximately 75% of the burner on
natural gas. For propane gas, do not place embers on main ports.
Note: Excessive use of embers may result in sooting or poor flame.
This appliance is provided with enough Glowing Embers for several
applications, do not feel compelled to use all that is in a new bag. For
best glowing effect, replace the ember material annually. Replace-
ment Glowing Embers are available (Catalog Number 88L53).
Step 4. Position the individual logs as shown in Figure 5 . Logs
should be placed in the order shown. Place logs 2 and 3 against
the pins on the grate, NOT over them.
Proper log and twig placement is critical to encourage outstanding
flame appearance and prevent sooting. When positioned properly
as shown, twigs will be positioned between flame peaks and will not
impinge any flames. Positioning is the same for all colors of log sets.
LENNOX HEARTH PRODUCTS
Glowing Embers (Rockwool)
For Propane Gas Only, Do Not Place Embers On Main Ports

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
2
CERAMIC PANEL PLACEMENT
Figure 3 Rustic Panel Kit Shown
STEP 3
STEP 1
STEP 4
STEP 2
L-Bracket Rear Wall
Bottom Rear Panel
L-Bracket
Grate Assembly
Right Side Panel
Top Rear Panel
Left Side Panel
L-BracketL-Bracket

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE. 3
CERAMIC PANEL CATALOG NUMBERS
Figure 4 (LSM45-2 Shown)
Mixture Of Volcanic Stone And Vermiculite
ecalperiF ledoM .oNgolataC .oNledoM noitpircseD
2-04MSL 9122H 04MSL-RKLB citsuR
2-04MSL 1084H 04MSL-RDER-KLB deR citsuR
2-04MSL 0222H 04MSL-HKLB enobgnirreH
2-04MSL 3084H 04MSL-HDER-KLB deR enobgnirreH
2-04MSL 1222H 04MSL-CKLB egattoCdlO
2-04MSL 2222H 04MSL-BKLB kcalB
2-54MSL 3222H 54MSL-RKLB citsuR
2-54MSL 2084H 54MSL-RDER-KLB deR citsuR
2-54MSL 4222H 54MSL-HKLB enobgnirreH
2-54MSL 4084H 04MSL-HDER-KLB deR enobgnirreH
2-54MSL 5222H 54MSL-CKLB egattoCdlO
2-54MSL 6222H 54MSL-BKLB kcalB

NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
4
Printed in U.S.A. © 2005 by Lennox Hearth Products
P/N 750,182M REV. B 04/2006
Lennox Hearth Products reserves the right to make changes at any time, without notice, in design, materials, specifications, prices and also to discontinue colors, styles and products.
Consult your local distributor for fireplace code information.
LHP
1110 West Taft Avenue • Orange, CA 92865
Figure 5
NOTE: DIAGRAMS & ILLUSTRATIONS NOT TO SCALE.
LSM40-2 & LSM45-2 LOG PLACEMENT
Log Number Description
1 Log, Center
2 Log, Rear
3 Log, Center/Left
4 Log, Center/Right
5 Log, Rear/Top
6 Log, Front/Left
7 Log, Front/Center
32
4
16
5
7
Align Groove At The Bottom Of Log (2) Over The
Grate And Push It Towards The Rear.
2
Align Two Holes At Bottom Of Log (1) Over The Pins On
The Gas Burner.
Engage Logs (3 & 4) With The Grate Pins And Align
Groves At The Bottom Of The Logs Over The Grate.
43
Engage Log (6) With The Grate
Pin And Align Groove At The
Bottom Of The Log Over The
Grate.
Align Hole At Bottom Of Log
(5) Over The Pin On Log (2).
Engage Log (7)
With The Pin On
Log (4).
6 5 7
1
2
4